Related Manuals for Yeti AS-Rsl
Summary of Contents for Yeti AS-Rsl
- Page 1 Yeti CYCles 600 Corporate Circle, Unit D Golden, CO p.303-278-6909 / 888-576-9384 www.yeticycles.com...
-
Page 2: Table Of Contents
Table of Contents Brand Overview Frame Features Geometry Maintenance Schedule Bike Setup Overview Shock Setup FOX RP3 Quick Start Guide Cable Routing Assembly Overview Assembly Disassembly Tips Exploded Views Part List Warranty Contact Information... - Page 3 It is impossible for this manual or the accompanying manuals to provide all the information required to properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Yeti retailer. Overview...
-
Page 4: Frame Features
Frame Features Pure tubinG Yeti Pure tubing is custom butted and tapered to make a lightweight and strong frame without the use of gussets. Unique shape provides added strength at the head tube junctions. bOttOm braCket 73mm shell, for use with a 113mm spindle... -
Page 5: Geometry
Geometry GeO metr Y a s- r 100 mm fOrk 16.75 18.0 19.0 21.3 21.0 22.4 23.4 24.4 16.9 16.9 16.9 16.9 40.3 41.6 42.6 43.6 12.75 12.75 12.75 12.75 27.5 28.0 28.0 28.0 5.25 *All measurements are in inches GeOmetrY... - Page 6 YETI has outlined below the service and maintenance that can and should be performed YETI has outlined a brief list of torque specifications for bolts and components that may need to by the owner and requires no special tools. Following these guidelines will help maintain the performance be tightened while performing basic maintenance.
-
Page 7: Bike Setup Overview
Authorized Fox Racing Shox service center for repair. To remove the shock from the linkage will require the Yeti linkage tool. The linkage tool is necessary to properly disassemble and reassemble the linkage. Using a hammer to tap out the pin can cause damage to the linkage and shock. -
Page 8: Quick Start Guide
Pressure The main air spring controls the sag of the shock. For quiCk start GuiDe rP3 as-r the AS-Rsl to ride properly you must setup the shock with the correct air sPrinG settinGs amount of sag. For general riding use 20-25% of the shock stroke. To increase sag reduce the main spring air pressure. - Page 9 CaPs Yeti recommends using metal end caps. The metal caps do not allow the cable to pull through as do the plastic versions. Do not mix up the shift and brake housing because it will result in a loss in performance.
-
Page 10: Assembly
Loctite compound or grease. disassembly on each bike Warning: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti Dealer assemblY... - Page 11 Pull the dickey or 8mm allen key out slightly so and align the nylon washers between the Dogbone and shock. You you can get the 2mm female bolt started. Tap the 22mm female Yeti want to make sure that the washers, shock eyelet, and Dogbone bearings bolt into position with the dead blow hammer.
- Page 12 Place a male Yeti bolt with a washer on the opposing side of the female bolt and thread into position. Cinch down both male Yeti bolts with the 5mm allen keys. The last step is to install the derailleur hanger and water bottle bolts.
-
Page 13: Disassembly Tips
Dogbone, shock connection point. On the opposing side slide this pin is two male Yeti bolts. Follow the instructions below to disassemble this pivot point. Also note there on the catch sleeve and washer, then thread the nut on. -
Page 14: Exploded Views
The individual components of each yeti bike are not sold separately. all yeti parts are sold in rebuild kits listed below. each and every part can be obtained by purchas- ing one of the rebuild kits. cross reference the part number you desire from the parts list to the rebuild list. - Page 15 BOLT-BUTTON hEAD M6X1X12 5MM 300030078 BOLT-PIVOT-MALE YETI CR-MO,CP M6X17MM 300020024 BEARING R62RSMAX MAIN PIVOT kOkO/AS-R 300030076 BOLT PIVOT FEMALE YETI CR-MO 35.5 MM 300030062 WAShER SS 6.5MM ID 12.5 OD .5MM Thk 300030069 WAShER SS 8.5MM ID 12.5MM OD .6MM Thk 200020039 AS-R MAIN BUShING REBUILD kIT ‘00-01...
- Page 16 INSERT - BUShING - ThREADED 300020001 BEARING 6903 300030054 BOLT - CAP 6X1X40 300030076 BOLT PIVOT FEMALE YETI CR-MO 35.5 MM 300020011 BUShING - TERCITE A - .750 ID 300030077 BOLT-PIVOT-FEMALE YETI CR-MO,CP 24.8MM 300030086 PIN - STEEL ShOCk - 1.30 AS-R/kOkO...
-
Page 17: Warranty
The (2) two year limited warranty is conditioned upon the bicycle being use of your bicycle. In the event that your frame breaks or malfunctions, YETI Cycles shall have no liability or ridden under normal conditions and having been properly maintained. This warranty does not apply to the obligation beyond the repair or replacement of your frame pursuant to the terms outlined in the warranty.