Table of Contents
Advertisement
Quick Links
HANBAY Inc
MDx-xxxDT-10.31
Contents
User's mounting
surface
Valve fluid
connections
Page 1 of 8
Rev: 2 - July, 2019
pg. 1-3
pg 1
pg 2
pg 2-3
pg. 3-5
pg 3-4
pg 4
pg 5
pg 6
pg 6
pg 6
pg. 6-7
pg 7
pg 7
pg. 8
Cable
Entry
Mounting
Bracket
Attachment Screws
8-32 x 1/2"
Installation
Mounting:
Usually, the actuator has to be mounted and supported as
shown in the picture to the left.
Exceptionally, and only if the application is vibration free and
the tubing is minimum ¼" dia. stainless, the actuator may be
suspended on the tubing itself.
User Manual MDx-xxxDT-10.31
www.hanbayinc.com
1 800 315 4461
hanbaysales@hanbayinc.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hanbay MD DT-10.31 Series
Summary of Contents for Hanbay MD DT-10.31 Series
- Page 1 HANBAY Inc User Manual MDx-xxxDT-10.31 MDx-xxxDT-10.31 Contents Installation pg. 1-3 Mounting pg 1 Wiring pg 2 Connecting power and signal pg 2-3 Operation pg. 3-5 DIP Switch settings pg 3-4 Functionality pg 4 Torque Settings pg 5 Setting the type of actuator...
- Page 2 HANBAY Inc User Manual MDx-xxxDT-10.31 Wiring: The actuator comes standard with a Turck 6 position connector and a 20’ cable with plug. Cut the cable to the length required and then connect according to the following wire color schematic: Wire color schematic for “Turck6” cable:...
- Page 3 HANBAY Inc User Manual MDx-xxxDT-10.31 Connect the signal: Locate the correct connection terminals as shown on the previous page then connect your input signal on pos. 1 and 2 and the output signals on 3 and 4 as shown below.
- Page 4 HANBAY Inc User Manual MDx-xxxDT-10.31 DIP 3 Reserved for custom function. DIP 4 Sets direction of offset. (Offset only available in MDH and MDF series) Sets the highest amount of offset, typically 12°. NOTE: To set maximum offset DIP’s 5,6 and 7 will DIP 5 need to be high for a total of 21°.
- Page 5 HANBAY Inc User Manual MDx-xxxDT-10.31 4-pos Functionality (Dip 8 ON) Input#1 Input#2 Action taken (Pin 1) (Pin 2) Back High High Moves to or remains in center position High Moves to or remains in right position High Moves to or remains in left position...
- Page 6 A sticking valve may be the problem. Remove the valve from the actuator, and re-test the actuator. Remove power. Re-check the wiring and the power/signal apparatus. Power actuator, and re-calibrate. If the problem persists, please call Hanbay for technical support. Page 6 of 8 www.hanbayinc.com...
- Page 7 HANBAY Inc User Manual MDx-xxxDT-10.31 Main Dimensions -xxxDT models Actuator connection cable: -xxxDT models Select a connection cable with 6 leads. The liquid tight strain relief on the base of the actuator is designed to accommodate a cable of O.D. 2.5 - 6.5mm (0.10 - 0.26in). Be sure to not use a cable with an OD that is no bigger than this! 2.- The cable has to...
- Page 8 HANBAY Inc User Manual MDx-xxxDT-10.31 Part Number Breakdown Serial Number: Full Hanbay Part Number: Page 8 of 8 www.hanbayinc.com Rev: 2 – July, 2019 1 800 315 4461 hanbaysales@hanbayinc.com...
Need help?
Do you have a question about the MD DT-10.31 Series and is the answer not in the manual?
Questions and answers