Advertisement
Quick Links
RDx-xxxDT- 10.31
Contents
Installation
Mounting
Wiring
Connecting power and signal
Manual override
Operation
DIP Switch settings
Functionality
Torque Settings
Appendix
Calibration
Trouble shooting
Dimensions
Factory Presets
Page 1 of 8
Rev.2020.4
pg. 1-3
pg 1
pg 2
pg 3
pg 3
pg. 4-6
pg 4
pg 5
pg 6
pg. 6-7
pg 6
pg 6
pg 7
pg. 8
Installation
Mounting:
Holes for a mounting bracket. Holes are
threaded for ¼-20 and are approximately
.275" deep.
For dimensions see page 7.
User Manual RDx-xxxDT-10.31
www.hanbayinc.com | 1 800 315 4461
hanbaysales@hanbayinc.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Hanbay RD-DT-10.31 Series
Summary of Contents for Hanbay RD-DT-10.31 Series
- Page 1 User Manual RDx-xxxDT-10.31 RDx-xxxDT- 10.31 Contents Installation pg. 1-3 Mounting pg 1 Wiring pg 2 Connecting power and signal pg 3 Manual override pg 3 Operation pg. 4-6 DIP Switch settings pg 4 Functionality pg 5 Torque Settings pg 6 Appendix pg.
- Page 2 User Manual RDx-xxxDT-10.31 Wiring: The actuator comes standard with a Turck 6 position connector and a 20’ cable with plug. Cut the cable to the length required and then connect according to the following wire color schematic: Wire color schematic for “Turck 6” cable: Color DC power supply only Turck connector not included...
- Page 3 User Manual RDx-xxxDT-10.31 Connect the signal: Locate the correct connection terminals as shown on the previous page, then connect your input signal on pos. 1 and 2 as shown below. Feedback, if applicable is connected to positions 3 and 4. USER SUPPLIED Input #1 Input #2...
-
Page 4: Operation
User Manual RDx-xxxDT-10.31 Operation DIP switches: The DIP switches allow you to change the settings on your actuator. To flip a switch, gently use a small flat-head screwdriver. See chart below for DIP switch functionality. DIP switches. In this example DIPs 1, 2, 6 and 12 are on. DiP 1 DiP 2 Fastest settling... - Page 5 User Manual RDx-xxxDT-10.31 Functionality of the RDx-xxxDT: The RDx can operate as a 3-position or 4-position actuator. The 4 position is enabled by turning Dip 8 ON. 3-pos Functionality (Dip 8 OFF) Input#1 Input#2 Action taken (Pin 1) (Pin 2) High High Moves to or remains in center position...
- Page 6 A sticking valve may be the problem. Remove the valve from the actuator, and re-test the actuator. Remove power. Re-check the wiring and the power/signal apparatus. Power actuator, and re-calibrate. If the problem persists, please call Hanbay for technical support. Page 6 of 8 www.hanbayinc.com | 1 800 315 4461...
- Page 7 User Manual RDx-xxxDT-10.31 Main Dimensions: RxL/RxM Desiccant sticks: These sticks change colour when exposed to moisture. When they change from the original color, blue, to pink, the actuator has been exposed to an excess of moisture. Page 7 of 8 www.hanbayinc.com | 1 800 315 4461 Rev.2020.4 hanbaysales@hanbayinc.com...
-
Page 8: Part Number Breakdown
User Manual RDx-xxxDT-10.31 Part Number Breakdown Serial Number: Full Hanbay Part Number: Page 8 of 8 www.hanbayinc.com | 1 800 315 4461 Rev.2020.4 hanbaysales@hanbayinc.com...
Need help?
Do you have a question about the RD-DT-10.31 Series and is the answer not in the manual?
Questions and answers