Table of Contents
  • Deutsch

    • Table of Contents
    • Geltung
    • Gerätekonfiguration/-Eigenschaften
    • Allgemeines
    • Anwendungsbereich, Einsatz In Gas- Und Staubatmosphären
    • Besondere Betriebsbedingungen
    • Sicherer Betrieb
    • Wichtige Hinweise für die Montage und Wartung
    • Elektrostatische Aufladung (Esd)
    • Elektrische Daten
    • Mechanische Daten
    • Thermische Daten
    • Installation
  • Français

    • Configuration / Propriétés Des Appareils
    • Domaine D'application, Utilisation Dans Des Atmosphères Gazeuses Et Poussiéreuses
    • Généralités
    • Validité
    • Conditions De Service Particulières
    • Fonctionnement Sécurisé
    • Instructions Importantes Pour Le Montage Et L'entretien
    • Charge Électrostatique (Esd)
    • Caractéristiques Électriques
    • Caractéristiques Mécaniques
    • Caractéristiques Thermiques
    • Installation
  • Español

    • Campo De Aplicación, Uso En Atmósferas De Gas Y Polvo
    • Configuración/Propiedades Del Equipo
    • Informaciones Generales
    • Vigencia
    • Condiciones De Operación Especiales
    • Funcionamiento Seguro
    • Indicaciones Importantes Para El Montaje Y Mantenimiento
    • Carga Electrostática (Esd)
    • Datos Eléctricos
    • Datos Mecánicos
    • Datos Térmicos
    • Instalación
      • Area of Applicability
      • Device Configuration/-Properties
      • General Information
      • Application Area, Use In Gas And Dust Atmospheres
      • Special Operating Conditions
      • Safe Operating Mode
      • Important Information For Mounting And Maintenance
      • Electrostatic Charging (Esd)
      • Electrical Data
      • Mechanical Data
      • Thermal Data
      • Installation
      • Area of Applicability
      • Device Configuration/-Properties
      • General Information
      • Application Area, Use In Gas And Dust Atmospheres (Zones And Divisions)
      • Special Operating Conditions
      • Safe Operating Mode
      • Important Information For Mounting And Maintenance
      • Electrostatic Charging (Esd)
      • Electrical Data
      • Mechanical Data
      • Thermal Data
      • Installation
      • Installation Diagram

Advertisement

Available languages

Available languages

Sicherheitshinweise / Safety
instructions
ATEX / IECEx / cULus
VEGAMET 841, 842, 861, 862
Installation in Zone 2
mit Ausgang Eigensicherheit "i"
Installation in Zone 2
with output intrinsic safety "i"
Document ID: 61274

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ATEX and is the answer not in the manual?

Questions and answers

Summary of Contents for Vega ATEX

  • Page 1 Sicherheitshinweise / Safety instructions ATEX / IECEx / cULus VEGAMET 841, 842, 861, 862 Installation in Zone 2 mit Ausgang Eigensicherheit "i" Installation in Zone 2 with output intrinsic safety "i" Document ID: 61274...
  • Page 2 EU-Baumusterprüfbescheinigung DEMKO 19 ATEX 2170X (Document ID: 61275) • Certificate of Conformity IECEx ULD 19.0016X (Document ID: 61276) • Certificate of Compliance cULus E505919 (Document ID: 61275) Editing status: 2020-07-23 ATEX / IECEx / cULus VEGAMET 841, 842, 861, 862...
  • Page 3 Sicherheitshinweise Safety instructions Consignes de sécurité Instrucciones de seguridad VEGAMET 841, 842, 861, 862 Installation in Zone 2 mit Ausgang Eigensicherheit "i" 0044 Document ID: 61274 ATEX...
  • Page 4: Table Of Contents

    12 Installation ..........................10 Ergänzende Dokumentation: • Betriebsanleitungen VEGAMET 841, 842, 861, 862 • EU-Baumusterprüfbescheinigung DEMKO 19 ATEX 2170X (Document ID: 61275) • EU-Konformitätserklärung (Document ID: 61837) Redaktionsstand: 2019-06-17 VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 5 VEGA upon request. Les présentes consignes de sécurité sont disponibles au téléchargement sous www.vega.com en standard en allemand, en anglais, en francais et en espagnol. VEGA met à disposition d'autres langues de l'Union Européenne selon les exigences.
  • Page 6: Geltung

    Gehen Sie auf "www.vega.com" und geben Sie im Suchfeld die Seriennummer Ihres Gerätes ein. Alternativ finden Sie alles über Ihr Smartphone: • VEGA Tools-App aus dem "Apple App Store", "Google Play Store" oder " Baidu Store" herunter- laden • DataMatrix-Code auf dem Typschild des Gerätes scannen oder •...
  • Page 7: Besondere Betriebsbedingungen

    Gerät entsprechend den Herstellerangaben, der EU-Baumusterprüfbescheinigung und entspre- chend den gültigen Vorschriften, Regeln und Normen installieren • Veränderungen am Gerät können den Explosionsschutz und somit die Sicherheit beeinträchti- • Veränderungen dürfen nur durch von der Firma VEGA autorisiertes Personal durchgeführt werden • Nur zugelassene Ersatzteile verwenden •...
  • Page 8: Elektrostatische Aufladung (Esd)

    Die Geräte sind so zu errichten/installieren, dass Folgendes ausgeschlossen werden kann: • elektrostatische Aufladungen durch Betrieb, Wartung und Reinigung • prozessbedingte elektrostatische Aufladungen, z. B. durch vorbei strömende Messstoffe Das Warnschild weist auf die Gefahr hin: VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 9: Elektrische Daten

    Die in der Tabelle angegebenen Maximalwerte können als kon- zentrierte Kapazitäten und konzentrierte Induktivitäten verwendet werden. Die Werte für IIC und IIB sind auch für staubexplosionsgefährdete Bereiche zulässig. VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 10 30 V DC Digital IN 2, Klemmen 24, 25, 26 30 mA Zusätzlich nur VEGAMET 862: Digital IN 3, Klemmen 27, 28, 29 Digital IN 4, Klemmen 30, 31, 32 VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 11: Mechanische Daten

    0,25 … 2,5 mm Überspannungskategorie Verschmutzungsgrad Thermische Daten Zulässige Umgebungstemperaturen Zulässige Umgebungstemperatur am Einbauort eines Umgebungstemperatur (Ta) Gerätes als Zugehöriges Betriebsmittel zur Installation in Zone 2 -40 … +50 °C (-40 … +122 °F) VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 12: Installation

    Wird der eigensichere Stromkreis in staubexplosionsgefährdete Bereiche der Zone 20 oder 21 geführt, ist sicherzustellen, dass die Betriebsmittel, die an diesen Stromkreisen angeschlossen werden, die Anforderungen der Kategorie 1D bzw. 2D erfüllen und entsprechend zertifiziert sind. VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 13: Inhaltsverzeichnis

    Supplementary documentation: • Operating instructions VEGAMET 841, 842, 861, 862 • EU-type approval certificate DEMKO 19 ATEX 2170X (Document ID: 61275) • EU declaration of conformity (Document ID: 61837) Editing status: 2019-06-17 VEGAMET 841, 842, 861, 862 • Installation in Zone 2...
  • Page 14 VEGA upon request. Les présentes consignes de sécurité sont disponibles au téléchargement sous www.vega.com en standard en allemand, en anglais, en francais et en espagnol. VEGA met à disposition d'autres langues de l'Union Européenne selon les exigences.
  • Page 15: Area Of Applicability

    VEGAMET 861 • VEGAMET 862 In accordance with the EU type approval certificate DEMKO 19 ATEX 2170X, as associated equipment for installation in Zone 2 (certificate number on type plate) and for all devices with safety instruction 61274. The classification as well as the respective standards are stated in the above certificates: Type of protection marking: •...
  • Page 16: Safe Operating Mode

    • Modifications on the instrument can influence the explosion protection and hence the safety • Modifications must only be carried out by employees authorized by VEGA company • Use only approved spare parts •...
  • Page 17: Electrostatic Charging (Esd)

    • process-related electrostatic charges, e.g. by measuring media flowing past The warning label indicates danger: WARNING - POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 18: Electrical Data

    IIB, IIIC Permissible external inductance L 0.2 mH 0.5 mH 0.5 mH 2 mH 10 mH Permissible external capacitance C 120 nF 88 nF 580 nF 470 nF 770 nF VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 19 30 V DC Digital IN 2, terminals 24, 25, 26 30 mA In addition only VEGAMET 862: Digital IN 3, terminals 27, 28, 29 Digital IN 4, terminals 30, 31, 32 VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 20: Mechanical Data

    2 -40 … +50 °C (-40 … +122 °F) Installation The controllers VEGAMET 841, 842, 861, 862 as associated equipment for installation in zone 2 VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 21 If the intrinsically safe circuit is led into dust-explosive areas of zone 20 or 21, please make sure that the instruments connected to these circuits meet the requirements of category 1D or 2D and are certified respectively. VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 22 • Notices de mise en service VEGAMET 841, 842, 861, 862 • Certificat de contrôle de type UE DEMKO 19 ATEX 2170X (ID de document : 61275) • Déclaration de conformité UE (ID du document : 61837) Date de rédaction : 2019-06-17 VEGAMET 841, 842, 861, 862 •...
  • Page 23 VEGA upon request. Les présentes consignes de sécurité sont disponibles au téléchargement sous www.vega.com en standard en allemand, en anglais, en francais et en espagnol. VEGA met à disposition d'autres langues de l'Union Européenne selon les exigences.
  • Page 24: Validité

    • VEGAMET 862 Conformément à l'agrément de certificat de contrôle de type UE DEMKO 19 ATEX 2170X, comme matériel associé pour installation en zone 2 (numéro de certificat sur la plaque signalétique) et pour tous les appareils avec la consigne de sécurité 61274.
  • Page 25: Conditions De Service Particulières

    UE et aux réglementations en vigueur. • Les modifications de l'appareil peuvent affecter la protection anti-déflagrante et ainsi la sécurité • Le personnel de la Société VEGA est le seul habilité à procéder à des modifications • Utiliser uniquement des pièces de rechange homologuées •...
  • Page 26: Charge Électrostatique (Esd)

    électrostatiques lors du fonctionnement, de la maintenance et du nettoyage • charges électrostatiques causées par le process, par ex. par le flux des produits à mesurer La plaque signalétique avertit contre le danger : VEGAMET 841, 842, 861, 862 • Installation en zone 2 ATEX...
  • Page 27: Caractéristiques Électriques

    Les valeurs maximales indiquées dans le tableau peuvent être utili- sées comme capacités concentrées et inductances concentrées. Les valeurs pour IIC et IIB sont aussi autorisées pour des zones explosibles poussiéreuses. VEGAMET 841, 842, 861, 862 • Installation en zone 2 ATEX...
  • Page 28 Digital IN 2, bornes 24, 25, 26 30 mA En supplément uniquement VEGAMET 862 : Digital IN 3, bornes 27, 28, 29 Digital IN 4, bornes 30, 31, 32 VEGAMET 841, 842, 861, 862 • Installation en zone 2 ATEX...
  • Page 29: Caractéristiques Mécaniques

    Caractéristiques thermiques Températures ambiantes admissibles Température ambiante tolérée sur le lieu de montage Température ambiante (Ta) d'un appareil comme matériel associé pour installation en zone 2 -40 … +50 °C (-40 … +122 °F) VEGAMET 841, 842, 861, 862 • Installation en zone 2 ATEX...
  • Page 30: Installation

    Si le circuit courant à sécurité intrinsèque passe dans des atmosphères explosibles de zone 20 ou 21, s'assurer que le matériel raccordé à ces circuits courant satisfait aux exigences des catégories 1D et/ou 2D et qu'il est certifié en conséquence. VEGAMET 841, 842, 861, 862 • Installation en zone 2 ATEX...
  • Page 31 Documentación adicional: • Instrucciones de servicio VEGAMET 841, 842, 861, 862 • Certificado de examen de tipo UE DEMKO 19 ATEX 2170X (Document ID: 61275) • Declaración de conformidad EU (Document ID: 61837) Estado de redacción: 2019-06-17 VEGAMET 841, 842, 861, 862 • Instalación en Zona 2...
  • Page 32 VEGA upon request. Les présentes consignes de sécurité sont disponibles au téléchargement sous www.vega.com en standard en allemand, en anglais, en francais et en espagnol. VEGA met à disposition d'autres langues de l'Union Européenne selon les exigences.
  • Page 33: Vigencia

    • VEGAMET 862 De acuerdo con el certificado de examen de tipo de la UE DEMKO 19 ATEX 2170X, como equipo correspondiente para instalación en zona 2 (Número de certificación en la placa de tipos) y para todos los instrumentos con la instrucción de seguridad 61274.
  • Page 34: Condiciones De Operación Especiales

    • Cambios en el instrumento pueden afectar la protección contra explosión y por lo tanto la seguridad • Modificaciones solamente pueden ser realizada por personal autorizado por la empresa VEGA. • Usar solo piezas de repuesto aprobadas • Para el montaje y desmontaje de componentes no incluidos en los documentos de homologa- ción, sólo se admiten aquellos componentes que corresponden técnicamente al estado están-...
  • Page 35: Carga Electrostática (Esd)

    • carga electrostática inducida por el proceso, por ejemplo, a causa del flujo de productos a medir El cartel de advertencia indica el riesgo: VEGAMET 841, 842, 861, 862 • Instalación en Zona 2 ATEX...
  • Page 36: Datos Eléctricos

    Los valores para IIC y IIB también son admisibles para zonas con peligro de explosión por polvo. Ex ia IIB, IIIC Inductividad externa permisible L 0,2 mH 0,5 mH 0,5 mH 2 mH 10 mH VEGAMET 841, 842, 861, 862 • Instalación en Zona 2 ATEX...
  • Page 37 30 V DC Digital IN 2, bornes 24, 25, 26 30 mA Adicional sólo VEGAMET 862: Digital IN 3, bornes 27, 28, 29 Digital IN 4, bornes 30, 31, 32 VEGAMET 841, 842, 861, 862 • Instalación en Zona 2 ATEX...
  • Page 38: Datos Mecánicos

    Temperatura ambiente permisible en el lugar de monta- Temperatura ambiente (Ta) je de un equipo como material correspondient para la instalación en -40 … +50 °C (-40 … +122 °F) zona 2 VEGAMET 841, 842, 861, 862 • Instalación en Zona 2 ATEX...
  • Page 39: Instalación

    20 o 21, hay que asegurar que los medios de producción a conectar en esos circuitos, cumplan con los requisitos de las categorías 1D o 2D y estén certificados correspon- dientemente. VEGAMET 841, 842, 861, 862 • Instalación en Zona 2 ATEX...
  • Page 40 Notes VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 41 Notes VEGAMET 841, 842, 861, 862 • Installation in Zone 2 ATEX...
  • Page 42 Die Angaben über Lieferumfang, Anwendung, Einsatz und Betriebsbedingungen der Sensoren und Auswertsysteme entsprechen den zum Zeitpunkt der Drucklegung vorhandenen Kenntnissen. Änderungen vorbehalten © VEGA Grieshaber KG, Schiltach/Germany 2019 VEGA Grieshaber KG Telefon +49 7836 50-0 Am Hohenstein 113 Fax +49 7836 50-201 77761 Schiltach E-Mail: info.de@vega.com...
  • Page 43 Safety instructions VEGAMET 841, 842, 861, 862 Installation in Zone 2 with output intrinsic safety "i" Document ID: 61274 IECEx...
  • Page 44 Contents Area of applicability ......................... 3 2 Device configuration/-properties ................... 3 General information ......................... 3 4 Application area, use in gas and dust atmospheres ............3 5 Special operating conditions ....................3 6 Safe operating mode ....................... 4 7 Important information for mounting and maintenance ............4 8 Electrostatic charging (ESD) ....................5 9 Electrical data........................... 6 10 Mechanical data ........................8 11 Thermal data ..........................
  • Page 45: Area Of Applicability

    The detailed device configurations can be retrieved using the serial number search on our home- page. Move to "www.vega.com" and enter in the search field the serial number of your instrument. Alternatively, you can find all via your smartphone: •...
  • Page 46: Safe Operating Mode

    Conformity and the valid regulations and standards • Modifications on the instrument can influence the explosion protection and hence the safety • Modifications must only be carried out by employees authorized by VEGA company • Use only approved spare parts •...
  • Page 47: Electrostatic Charging (Esd)

    Maintenance To ensure the functionality of the device, periodic visual inspection is recommended for: • Secure mounting • No mechanical damages or corrosion • Worn or otherwise damaged cables • The potential equalization terminal must be secured against loosening • Correct and clearly marked cable connections Intrinsic safety "i"...
  • Page 48: Electrical Data

    Electrical data VEGAMET 841, 842 Non-intrinsically safe circuit Supply circuit: Terminals 91[+, L], 92[-, N] U = 24 … 65 V DC (-15 … +10 %) P = 4 W (VEGAMET 841), 5 W (VEGAMET 842) U = 100 … 230 V AC (-15 … +10 %), 50/60 Hz P = 13 VA (VEGAMET 841), 15 VA (VEGAMET 842) = 253 V AC (only for Ex ia) Relay output:...
  • Page 49 VEGAMET 861, 862 Non-intrinsically safe circuit Supply circuit: Terminals 91[+, L], 92[-, N] U = 24 … 65 V DC (-15 … +10 %) P = 6 W (VEGAMET 861), 7 W (VEGAMET 862) U = 100 … 230 V AC (-15 … +10 %), 50/60 Hz P = 17 VA (VEGAMET 861), 19 VA (VEGAMET 862) = 253 V AC (only for Ex ia) Relay output:...
  • Page 50: Mechanical Data

    Intrinsically safe circuit Supply and signal circuit: 4 … 20 mA-Sensor 1: Terminals 1[+], 2[-] In type of protection intrinsic safety Ex ia IIC, IIB/IIIC. In addition only VEGAMET 862: For connection to a certified, intrinsically safe circuit. 4 … 20 mA sensor 2: Terminals 4[+], 5[-] ≤...
  • Page 51 can be mounted and operated within hazardous areas of zone 2. For zone 2: The equipment must be mounted in a housing that has been tested according to IEC 60079-0 and meets the requirements of protection class IP54. The device may then only be installed in locations that offer adequate protection against the ingress of solid foreign objects or liquids.
  • Page 52 Notes VEGAMET 841, 842, 861, 862 IECEx...
  • Page 53 Notes VEGAMET 841, 842, 861, 862 IECEx...
  • Page 54 Subject to change without prior notice © VEGA Grieshaber KG, Schiltach/Germany 2019 VEGA Grieshaber KG Phone +49 7836 50-0 Am Hohenstein 113...
  • Page 55 Safety instructions VEGAMET 841, 842, 861, 862 Installation in Zone 2/Division 2 with output intrinsic safety "i" Document ID: 61274 c-UL-us...
  • Page 56 Contents Area of applicability ......................... 3 2 Device configuration/-properties ................... 3 General information ......................... 3 4 Application area, use in gas and dust atmospheres (zones and divisions) ...... 4 5 Special operating conditions ....................4 6 Safe operating mode ....................... 4 7 Important information for mounting and maintenance ............4 8 Electrostatic charging (ESD) ....................5 9 Electrical data........................... 6 10 Mechanical data ........................8 11 Thermal data ..........................
  • Page 57: Area Of Applicability

    Move to " www.vega.com" and enter in the search field the serial number of your instrument. Alternatively, you can find all via your smartphone: • Download the VEGA Tools app from the " Apple App Store", " Google Play Store" or " Baidu Store" •...
  • Page 58: Application Area, Use In Gas And Dust Atmospheres (Zones And Divisions)

    Modifications on the instrument can influence the explosion protection and hence the safety, therefore repairs are not permitted to be conducted by the end user • Modifications must only be carried out by employees authorized by VEGA company VEGAMET 841, 842, 861, 862 c-UL-us...
  • Page 59: Electrostatic Charging (Esd)

    • Use only approved spare parts • Components for installation and connection not included in the approval documents are only permitted if these correspond technically to the latest standard mentioned on the cover sheet. They must be suitable for the application conditions and have a separate certificate. The special conditions of the components must be noted and if necessary, the components must be inte- grated in the type test.
  • Page 60: Electrical Data

    The warning label indicates danger: WARNING - POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS Electrical data VEGAMET 841, 842 Non-intrinsically safe circuit Supply circuit: Terminals 91[+, L], 92[-, N] U = 24 … 65 V DC (-15 … +10 %) P = 4 W (VEGAMET 841), 5 W (VEGAMET 842) U = 100 …...
  • Page 61 Ex ia IIB, IIIC Permissible external inductance L 0.2 mH 0.5 mH 0.5 mH 2 mH 10 mH Permissible external capacitance C 120 nF 88 nF 580 nF 470 nF 770 nF VEGAMET 861, 862 Non-intrinsically safe circuit Supply circuit: Terminals 91[+, L], 92[-, N] U = 24 …...
  • Page 62: Mechanical Data

    Intrinsically safe circuit Supply and signal circuit: 4 … 20 mA-Sensor 1: Terminals 1[+], 2[-] In type of protection intrinsic safety Ex ia IIC, IIB/IIIC. In addition only VEGAMET 862: For connection to a certified, intrinsically safe circuit. 4 … 20 mA sensor 2: Terminals 4[+], 5[-] ≤...
  • Page 63 2 can be mounted and operated within hazardous areas of zone 2/Div 2. For zone 2: The equipment must be mounted in a housing that has been tested according to IEC 60079-0 and meets the requirements of protection class IP54. The device may then only be installed in locations that offer adequate protection against the ingress of solid foreign objects or liquids.
  • Page 64: Installation Diagram

    Installation diagram VEGAMET 841, 842, 861, 862 c-UL-us...
  • Page 65 VEGAMET 841, 842, 861, 862 c-UL-us...
  • Page 66 Subject to change without prior notice © VEGA Grieshaber KG, Schiltach/Germany 2020 VEGA Grieshaber KG Phone +49 7836 50-0 Am Hohenstein 113...
  • Page 67 ATEX / IECEx / cULus VEGAMET 841, 842, 861, 862...
  • Page 68 Subject to change without prior notice © VEGA Grieshaber KG, Schiltach/Germany 2020 VEGA Grieshaber KG Phone +49 7836 50-0 Am Hohenstein 113...

This manual is also suitable for:

IecexCulusVegamet 841Vegamet 842Vegamet 861Vegamet 862

Table of Contents