Table of Contents
Advertisement
operation is required. To complete the assembly the
following instructions will be helpful.
1. TROWELS – Attach trowel blades with screws and
lock washers supplied. See (A) and (B) Fig. 1. Be
SAFETY PRECAUTIONS
careful that adjusting screw (C) does not protrude
Always keep unauthorized, inexperienced, untrained
below arm when attaching blades. This could cause
people away from this machine.
the machine to jump and promote excessive wear in
Rotating and moving parts will cause injury if
operation.
2. STABILIZER RING – (if supplied) Install using
contacted. Make sure guards are in place. Keep
hands and feet away from moving parts.
screws, bushings and lock washers supplied. See
Fuel the machine only when the engine is stopped,
Fig. 1 (D)
3. HANDLE ASSEMBLY – Put cable end Fig. 2 (A)
using all necessary safety precautions.
The engine must always be stopped before
through hole in yoke (B) and secure with nut (C),
attempting any repair or adjustments. Ignition switch
then install handle bracket on gearbox. To get
should be off.
proper cable tension, turn control knob Fig. 3,
Be careful not to come in contact with the muffler
counter-clockwise to stop position. Guide screw (B)
when the engine is hot, serious burns may result!
will now be at the bottom slot. Tighten nut Fig. 4 (A)
until slack is removed from point (B) as indicated. If
DANGER:
more than 2 or 3 threads show through, then nut
Never operate the machine in an explosive
should be turned back.
atmosphere, near combustible materials or where
Guide screw, Fig. 3 (B) should be moved to next
ventilation does not clear exhaust fumes. Repair
lower hole in slide bushing and cable re-adjusted as
fuel leaks immediately. Refer to your engine
above. Turn hand knob completely clockwise and
owner's manual for more safety instructions.
check for clearance between yoke and gearbox at
point (C) Fig. 4. There should be enough space to
pass a business card through.
ASSEMBLY INSTRUCTIONS
Your new Bartell Walk-Behind Power Trowel has been
shipped to you partially assembled. Filling the fuel tank
and a brief check of lubricant levels in preparation for
operation is required. To complete the assembly the
following instructions will be helpful.
375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA L5T 3A7, 905-364-4200 FAX 905-364-4201
1. TROWELS – Attach trowel blades with screws and
lock washers supplied. See (A) and (B) Fig. 1. Be
careful that adjusting screw (C) does not protrude
below arm when attaching blades. This could cause
the machine to jump and promote excessive wear in
operation.
2. STABILIZER RING – (if supplied) Install using
screws, bushings and lock washers supplied. See
Fig. 1 (D)
3. HANDLE ASSEMBLY – Put cable end Fig. 2 (A)
STATIONARY RING - Install stationary ring as shown
through hole in yoke (B) and secure with nut (C),
in Fig. 5 with the side bar on engine recoil side (may
then install handle bracket on gearbox. To get
not be exactly as shown). install rubber bushings (A)
proper cable tension, turn control knob Fig. 3,
on top and bottom of mounting plate. Install metal caps
counter-clockwise to stop position. Guide screw (B)
(B). Placing ring on top and run screw (C) through caps
will now be at the bottom slot. Tighten nut Fig. 4 (A)
and rubbers. Tigthen lock nut (D) securely on bottom.
until slack is removed from point (B) as indicated. If
It is best to start nuts on all 4 corners before tigthening.
more than 2 or 3 threads show through, then nut
should be turned back.
Guide screw, Fig. 3 (B) should be moved to next
lower hole in slide bushing and cable re-adjusted as
above. Turn hand knob completely clockwise and
check for clearance between yoke and gearbox at
point (C) Fig. 4. There should be enough space to
pass a business card through.
375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA L5T 3A7, 905-364-4200 FAX 905-364-4201
375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX 905-364-4201
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-5400 FAX 732-566-5444
WALK BEHIND POWER TROWEL INSTRUCTION MANUAL
WALK-BEHIND TROWEL INSTRUCTION MANUAL
throttle block in the fully open position, cut the inner
cable by the thumb lever, leaving enough wire
exposed to secure to the lever. Insert the cable into
the fitting and tighten the screw. Restore throttle to
idle position.
STATIONARY RING –
4.
IMPORTANT:
shown in Fig. 5 with the side bar on engine recoil
Before running machine with belt installed, ensure
side. (May not be exactly as shown). Install rubber
that engine idles properly and that the safety -switch
bushings (A) on top and bottom of mounting plate.
shuts off the engine.
Install metal caps (B). Place ring on top and run
screw (C) through caps and rubbers. Tighten lock nut
BELT GUARD
6.
– Install after machine has been
(D) securely on bottom. It is best to start nuts on all 4
tested, taking care that it does not touch clutch or
corners before tightening.
pulley.
ENGINE CONTROLS
5.
ATTENTION:
handle with screws provided. See DIAGRAM 1 below
For any information regarding engine adjustments,
for your engine model hook-up. For safety switch
please refer to the engine manual supplied.
connection, attach wire to terminal provided at
"ON/OFF" location.
The throttle cable must be cut and formed to fit. Feed
the cable through the cable clamp on the engine. Pull
the cable through the clamp until it forms a smooth
arc from the handle to the engine. Mark the cable at
the clamp and pull the cable back from the casing at
the throttle. Without cutting the cable, Cut casing at
the mark and push the cable back through fresh cut
end. Form a small "L" bend in the cable, hook the
inner cable into the throttle block and tighten cable
clamp down onto the casing. With thumb lever and
throttle block in the fully open position, cut the inner
cable by the thumb lever, leaving enough wire
exposed to secure to the lever. Insert the cable into
the fitting and tighten the screw. Restore throttle to
idle position.
9
IMPORTANT:
Before running machine with belt installed, ensure
that engine idles properly and that the safety -switch
shuts off the engine.
BELT GUARD
6.
– Install after machine has been
tested, taking care that it does not touch clutch or
pulley.
ATTENTION:
For any information regarding engine adjustments,
please refer to the engine manual supplied.
9
9
Install stationary ring as
– Attach throttle control to
CREATED: 07/04
REVISED: 05/10
CREATED: 07/04
REVISED: 05/10
CREATED: 07/04
REVISED: 07/14
Advertisement
Table of Contents
