Page 1
Installation and Maintenance manual TIE BAR PARTNER (Dr. No. 36010 10/12/2019)
Page 2
2013/53/EU. "Established in 1989 UFLEX USA is a leader in steering and control systems for the marine industry. With full manufacturing capabilities in Sarasota, Florida, UFLEX USA can support all sectors of the marine industry regardless of volume and/or product requirements.
SECTION 2 - INSTALLATION ���������������������������������������������������������������������������������������������������������������������������� NECESSARY TOOLS ���������������������������������������������������������������������������������������������������������������������������� A95 INSTALLATION ���������������������������������� ADJUSTMENT OF THE DISTANCE BETWEEN CENTERS WITH INSTALLED BAR SECTION 3 - MAINTENANCE ���������������������������������������������������������������������������������������������������������������� ORDINARY MAINTENANCE ����������������������������������������������������������������������������������������������������� EXTRAORDINARY MAINTENANCE SECTION 4 - DISMANTLING ���������������������������������������������������������������������������������������������������������������������������������� DISMANTLING page 3 of 19 TIE BAR A95...
Page 4
Installation and Maintenance Manual DOCUMENT REVISIONS Rev. Date Revision description 10/12/2019 First edition page 4 of 19 - TIE BAR A95...
Page 5
= kilometres per hour 10 m.p.h. = 8,69 knots 10 m.p.h. = 16,1 km/h 10 knots = 11,5 m.p.h. 10 knots = 18,5 km/h 10 km/h = 6,21 m.p.h. 10 km/h = 5,4 knots page 5 of 19 TIE BAR A95...
Page 6
1. Two Year Limited Warranty. UFLEX USA, Inc. warrants that all products manufactured by UFLEX USA, Inc. or UFLEX S.p.A. and sold by UFLEX USA to the retail purchaser ("Purchaser") that for two (2) years after the date of manufacture to be free from defects due to material or workmanship, subject to the exclusions below.
Page 7
4. Transferability of Warranty. This limited warranty may not be transferred to subsequent purchasers. 5. Miscellaneous. UFLEX USA, Inc. is an affiliate of UFLEX S.p.A. UFLEX, USA, Inc., reserves the right to make changes in the design and construction of its products at any time, without notice and without any obligation to incorporate such changes into products of prior manufacture.
1.1 General features The bar A95 is completely made up of stainless steel and it is already preassembled and ready to be installed. Its length can be adjusted: the distance between centers varies from 660 (26’’) to 812 mm (32’’) and from 812 (32’’) to 950 mm (37.5’’) according to the version (A95-32 and A95-37.5).
22 mm hexagon wrench Cross slot screwdriver Dynamometric wrench Loctite 270 2.2 A95 Installation Install the cylinders by carrying out the instruc- tions indicated in the manual and positioning the engines as shown in the pictures indicated in point 2.
Page 10
(5) applying some strong Loctite 270 with a 3[Nm] (2 [lb∙ft]) tightening torque. DANGER The non-use of screw (5) and of safety washer (4) results in dangers to things and injury of people. page 10 of 19 - TIE BAR A95...
Before carrying out the following operations, it is mandatory to turn off the engines and operate in safe conditions. Loosen the ring nut (1) by means of a 22 mm wrench holding it still with a second wrench on the end element (2). page 11 of 19 TIE BAR A95...
Page 12
Once this length is reached, tighten the ring nut (1) again by means of a 22 mm wrench with a tightening torque of 40 [Nm] (29.52 [lb ∙ ft]) using a second wrench on the end element (2). page 12 of 19 - TIE BAR A95...
When for any reason, the system is put out of service, it is necessary to follow some rules in order to respect the environment. Sheaths, pipelines, plastic or non-metallic components must be disassembled and disposed of separately. page 13 of 19 TIE BAR A95...
Page 14
Installation and Maintenance Manual NOTES page 14 of 19 - TIE BAR A95...
Page 15
Installation and Maintenance Manual NOTES page 15 of 19 TIE BAR A95...