Summary of Contents for pottery barn kids CHARLIE TWIN OVER TWIN BUNK BED
Page 1
CHARLIE TWIN OVER TWIN BUNK BED www.potterybarnkids.com Date: 2015-Nov-14 Rev: Page 1 of 13...
Page 2
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use bunk bed if any parts are missing or broken. DO NOT use substitute parts. Contact pottery barn kids for replacement parts and instructional literature if needed.
Page 3
Important Safety Instructions: Please read all instructions carefully before assembling. For your safety, assembly by two or more adults is strongly recommended. Keep instructions for future use. Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural integrity of the item.
Page 4
Hardware Included: (H) Half-moon washer (I) Flat Washer M6 (J) Spring Washer M6 (K) Allen Bolt M6x60 mm – 16x M6 - 16x (L) Allen key with ball tip (M) Short flat head wood (N) Long flat head wood (O) Bracket screw screw 4x15 mm –...
Page 5
Carefully attach (C) onto (B) as shown below. Attach the remaining (A) to (B) by aligning pre-drilled holes with wooden dowels as shown below. Do not over tighten. Date: 2015-Nov-14 Rev: Page 5 of 13...
Page 6
Secure (C) to (B) by short wood screw (M) as shown below. Determine the desired location of the ladder opening (use options below). Ladder on the LEFT Ladder on the RIGHT Date: 2015-Nov-14 Rev: Page 6 of 13...
Page 7
Attach (D) to (B) as shown below. Secure (D) by short wood screw (M). Secure (C&D) to (A) with metal bracket (O) and machine screw (P) using a Phillips head screwdriver (Not included) as shown below. Date: 2015-Nov-14 Rev: Page 7 of 13...
Page 8
Extend and place (F) onto inner ledge of Side Rails (B). Secure each slat with wood screw (N) using a Phillips head screwdriver (not included). & & ASSEMBLE THE LOWER BED Repeat step #1 to assemble (B) to (E) as shown below. Do not over tighten. Date: 2015-Nov-14 Rev: Page 8 of 13...
Page 9
Repeat step #3 to assemble the remaining (B) to (E) as shown below. Do not over tighten. Repeat step # 8 to assemble (F) to the assembled bed. Do not over tighten. Date: 2015-Nov-14 Rev: Page 9 of 13...
Page 10
Thread (Q) onto top of (E) as shown below. With the help of another person, lift the upper bed (with guardrails) and place over the lower bed as shown below. Make sure the threaded iron dowels (Q) are well inserted into the holes on bottom of upper bed posts.
Page 11
Hook the ladder (G) onto the upper and lower bed side rails (B) as shown below. Secure (G) as shown below, using a Phillip Head Screwdriver (not included). Date: 2015-Nov-14 Rev: Page 11 of 13...
Page 12
Turn the pre-installed brackets on the bottom of guard rails (C&D) to correct direction as shown below. Secure the brackets to (B) with screw (M), using a Phillip Head Screwdriver (not included). C&D Assembly now is completed. Date: 2015-Nov-14 Rev: Page 12 of 13...
Page 13
To convert the bunk bed into two twin beds, use tall end boards (E) as head boards and short end boards (A) as foot boards. a. Assemble beds following instructions in steps #1 & #3. b. Assemble slats following instructions in step # 8. c.