Table of Contents
Advertisement
PRO1 V11.xxx series MID
DIN rail single phase two wire energy meter
Version 1.12
Note: the picture on the frontpage is a meter from the series of this meter, it might not
be exactly the same as the meter you bought
PRO1D V11.111
PRO1D V11.112
PRO1D V11.121
PRO1D V11.122
PRO1D V11.211
PRO1D V11.212
PRO1D V11.221
PRO1D V11.222
Advertisement
Table of Contents
Related Manuals for Inepro DMMetering PRO1 V11 Series
Summary of Contents for Inepro DMMetering PRO1 V11 Series
- Page 1 PRO1 V11.xxx series MID DIN rail single phase two wire energy meter PRO1D V11.111 PRO1D V11.112 PRO1D V11.121 PRO1D V11.122 PRO1D V11.211 PRO1D V11.212 PRO1D V11.221 PRO1D V11.222 Version 1.12 Note: the picture on the frontpage is a meter from the series of this meter, it might not be exactly the same as the meter you bought...
-
Page 2: Table Of Contents
Safety instructions .....................3 Foreword ........................4 MID certificate......................5 CE certificates ......................6 Type number table .....................8 Performance criteria ....................8 Specifications ......................8 Basic errors ......................9 Description .......................9 10 Dimensions .......................9 11 Installation ......................10 12 Operation ....................... 11 12.1 Consumption indication ..................11 12.2 Reading the meter ..................... -
Page 3: Safety Instructions
Use for the intended purpose This device may only be used for the application cases specified in the catalog and the user manual and only in connection with devices and components recommended and approved by Inepro Metering B.V. Proper handling The prerequisites for perfect, reliable operation of the product are proper transport, storage, installation and connection, as well as proper operation and maintenance. -
Page 4: Foreword
It is prohibited to pass on or copy this document or to use or disclose its contents without express permission of Inepro Metering BV. Any duplication is a violation of the law and subject to criminal and civil penalties. All rights reserved, particularly for pending or approved patent awards or registered trademarks. -
Page 5: Mid Certificate
3 MID certificate ® 2011 - 5 - For the SOP number see section 15 PRO1 V11.xxx... -
Page 6: Ce Certificates
4 CE certificates ® 2011 - 6 - For the SOP number see section 15 PRO1 V11.xxx... - Page 7 ® 2011 - 7 - For the SOP number see section 15 PRO1 V11.xxx...
-
Page 8: Type Number Table
5 Type number table The PRO1 series is labeled as follows: PRO1D/TE V 11 . x x x Pulse led and pulse output: 1 = 1000 impulses / kWh 2 = 2000 impulses / kWh Reverse counting: 1 = Does not count when energy is reversed 2 = Counts up regardless of energy direction Type of display: 1 = LCD without backlight... -
Page 9: Basic Errors
8 Basic errors 0.05Ib Cosφ = 1 ±1.5% 0.1Ib Cosφ = 0.5L ±1.5% Cosφ = 0.8C ±1.5% 0.1Ib - Imax Cosφ = 1 ±1.0% 0.2Ib - Imax Cosφ = 0.5L ±1.0% Cosφ = 0.8C ±1.0% 9 Description Display register Terminal block Case Protection cover Security wire slot... -
Page 10: Installation
Height 120 mm Height without protection cover 91 mm Width 18 mm Depth 58.5 mm Max diameter power connection clamps 8 mm Weight 0.08 Kg (net) 11 Installation CAUTION Turn off and if possible lock all sources supplying the energy meter and the equipment that is connected to it before working on it. -
Page 11: Operation
Connection of the wires should be done in accordance with the connection diagram as shown below: phase line in (L-IN) phase line out (L-OUT) neutral line in (N) neutral line out (N) 20 and 21 Pulse output contact (S0) 12 Operation 12.1 Consumption indication There is a red LED on the front panel which indicates the consumption measured by the meter. - Page 12 It generates pulses in proportion to the measured consumption for purpose of remote reading or accuracy testing. The pulse output is a polarity dependent, open-collector transistor output requiring an external voltage source for correct operation. For this external voltage source, the voltage (Ui) should be lower than 27V DC.
-
Page 13: Troubleshooting
13 Troubleshooting CAUTION During repair and maintenance, do not touch the meter connecting clamps directly with your bare hands, with metal, blank wire or other conducting material as that will cause an electric shock and possibly cause injury, serious injury or even death. ... -
Page 14: Technical Support
14 Technical support For questions about one of our products please contact: Your local Inepro Metering distributor Email: support@ineprometering.com www.ineprometering.com 15 SOP Table PRO1D V11.111 (mold BII) 0174 PRO1D V11.112 (mold BII) 0175 PRO1D V11.121 (mold BII) - Page 15 This page is left blank on purpose ® 2011 - 15 - For the SOP number see section 15 PRO1 V11.xxx...
- Page 16 This page is left blank on purpose ® 2011 - 16 - For the SOP number see section 15 PRO1 V11.xxx...