Table of Contents
Advertisement
ELECTRICAL SAFETY
ELECTRICAL SAFETY
ELECTRICAL SAFETY
ELECTRICAL SAFETY
ELECTRICAL SAFETY
Electrical Shock
• Turn off the electrical supply to the disposer before ser-
vicing. (Test the circuit with a volt meter or circuit tester
to ensure the power is off.)
• All control centers and disposers must be grounded.
• A properly fused disposer control (with a marked "off"
position) that disconnects all ungrounded supply con-
ductors must be installed at the electrical supply source.
Personal Injury/Property Damage
If the electrical installer is not experienced in electrical in-
stallation, we recommend seeking competent professional
assistance. Disposer or accessory damage due to im-
proper installation is not covered under warranty. All in-
stallations must comply with local electrical codes.
Property Damage
• Disposers shipped from the factory are not wired for a
specific voltage. Refer to the motor connection wiring
diagram in the terminal box for voltage instructions.
• Ensure that the disposer motor voltage and phase match
that of the electrical supply.
DISPOSER CONTROLS
DISPOSER CONTROLS
DISPOSER CONTROLS
DISPOSER CONTROLS
DISPOSER CONTROLS
Install the disposer controls within sight of the disposer (per local codes) so the disposer can be reached easily in an
emergency situation. In-Sink-Erator approved disposer/control combinations are listed in Table 3.
Model Phase
SS-50
SS-50
SS-75
SS-75
SS-100
SS-100
SS-125
SS-125
SS-150
SS-150
SS-200
SS-200
SS-300
SS-500
SS-750
SS-1000
X = Approved
O = Not Approved
AS101
Manual
Start Switch
1
X
X
3
X
X
1
X
X
3
X
X
1
X
X
3
X
X
1
X
X
3
X
X
1
X
X
3
X
X
1
X
X
3
X
X
3
X
O
3
X
O
3
X
O
3
X
O
Table 3: Approved Disposer/Control Combinations
Table 3:
Table 3:
Table 3:
Table 3:
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
To connect the disposer to the electricity:
1 . Remove the screw in the center of the disposer
terminal box.
2. Pull the terminal box out of the stainless-steel trim
shell.
3. Connect an electrical conduit connector to the hole
in the bottom of the exposed wiring compartment.
4. Connect the ground wire to the ground screw.
5. Connect the incoming wires to the motor leads.
(Make sure the wiring connections are the same as
those on the motor control wiring diagram for your
specific control.) (See pages 10 - 17.)
6. Reinstall the terminal box cover on the trim shell.
Be careful not to pinch or damage the electrical wires when
replacing the terminal box.
NOTE:
NOTE:
NOTE:
NOTE: Complete electrical information is located
NOTE:
inside the disposer terminal box.
7. Test the disposer to ensure that the cutting elements
revolve and the water flows automatically. Make
sure the disposer is securely mounted and does not
leak from any of the connections.
Magnetic
Manual
Starter Switch
Reverse Switch
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
O
7
ELECTRICAL
ELECTRICAL
ELECTRICAL
ELECTRICAL
ELECTRICAL
Electric Shock
CC101 CC202
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
X
X
O
X
X
Hide quick links:
Advertisement
Table of Contents
