Standard In-Sink-Erator Mountings - InSinkErator 13954 Installation & Use Manual

DISPOSER MOUNTING DISPOSER MOUNTING
DISPOSER MOUNTING DISPOSER MOUNTING DISPOSER MOUNTING

STANDARD IN-SINK-ERATOR MOUNTINGS

STANDARD IN-SINK-ERATOR MOUNTINGS STANDARD IN-SINK-ERATOR MOUNTINGS
STANDARD IN-SINK-ERATOR MOUNTINGS STANDARD IN-SINK-ERATOR MOUNTINGS
# 5 MOUNTING ASSEMBLY # 5 MOUNTING ASSEMBLY # 5 MOUNTING ASSEMBLY # 5 MOUNTING ASSEMBLY # 5 MOUNTING ASSEMBLY
Follow these instructions to install a #5 sink flange to a
standard 3 1/2 - 4 inch sink opening.
1 . Unscrew the three backup screws (6 6 6 6 6 ) until they are
flush with the upper mounting flange (5 5 5 5 5 ) surface.
Pry the retainer ring (7 7 7 7 7 ) free from the strainer flange
(2 2 2 2 2 ) with a screwdriver and separate all mounting
2 - 7 2 - 7
assembly parts (2 - 7 2 - 7 2 - 7).
2. Form a 3/4" thick ring of top grade oil base putty
around the sink opening (use non-hardening putty).
Insert the strainer flange (2 2 2 2 2 ) into the sink opening
and press firmly in place. Clean away any excess
putty.
3. From underneath the sink, place the strainer flange
gasket (3 3 3 3 3 ), backup flange (4 4 4 4 4 ) - flat side up, and upper
mounting flange (5 5 5 5 5 ) over the strainer flange and
hold them up to the sink. Snap the retainer ring (7 7 7 7 7 )
into the groove on the strainer flange to hold the
mounting parts in place.
4. Tighten the three backup screws evenly until the
backup flange draws snugly against the underside of
the sink and the strainer flange is held securely in
place.
5. Place the body flange (9 9 9 9 9 - lugs upward) over the lip
of the mounting flange (10 10 10 10 10) and fit the mounting
gasket (8 8 8 8 8 ) onto the lip.
6. Place the mounting gasket (11 11 11 11 11) on the disposer
body flange. Secure the mounting flange (10 10 10 10 10) to the
disposer body flange with six screws (12 12 12 12 12) provided.
7. Raise the disposer to the upper mounting flange (5 5 5 5 5 )
so the body flange (9 9 9 9 9 ) is positioned with the lugs to
the right of the screws.
8. While supporting the disposer, turn the body flange
(9 9 9 9 9 ) to the right until all three lugs are engaged in the
mounting flange (5 5 5 5 5 ). Swivel the disposer to align
the discharge outlet with the drain trap. (The
disposer can be truned 360 degrees.)
9. Align the disposer to the plumbing connection and
insert the service wrench into the left side of a lug
and continue to turn the body flange to the right
(approximately one quarter turn) until it locks onto
the notches on the upper mounting flange .
NOTE: NOTE: NOTE: NOTE: NOTE: Special mounting instructions are included in
the #5 #5 #5 Short #5 Short Mounting Kit. Short Short Mounting Kit. Mounting Kit. Mounting Kit.
#5 Short Mounting Kit.
(1) S
(2) S
TRAINER
(3) S F
TRAINER LANGE
(4) B
ACKUP
(5) U M
PPER
F
LANGE
(6) B
ACKUP
(7) R
ETAINER
(8) M
OUNTING
(9) B
ODY
(10) M
OUNTING
(11) M
OUNTING
D B
ISPOSER ODY
(12) 1/4" S
* Included as part of the disposer.
Figure 3: #5 Mounting Assembly Figure 3: Figure 3: Figure 3: Figure 3:
4
TOPPER
F
LANGE
S *
INK
G
ASKET
F
LANGE
OUNTING
S
CREW
R
ING
G
ASKET
F
LANGE
F
LANGE
G
ASKET
F *
LANGE
CREW