Advertisement
Turbine Series
900FH and 1000FH
Fuel Filter/Water Separators
Instruction Part Number 12960 Rev E
Turbine Series filters protect
precision engine components
from dirt, rust, algae, asphaltines,
varnishes, and especially water,
which is prevalent in engine fuels.
They remove contaminants from
fuel using the following legendary
three stage process:
Stage 1 - Separation
As fuel enters the assembly, it
moves through the centrifuge and
spins off large solids and water
droplets, which are heavier than
fuel, and fall to the bottom of the
collection bowl.
Stage 2 - Coalescing
Small water droplets bead-up on
the surface of the conical baffle
and cartridge filter. When heavy
enough, they too fall to the bottom
of the collection bowl.
Stage 3 - Filtration
®
Proprietary Aquabloc
filters repel water and remove
contaminants from fuel down to
2 micron (nominal). Aquabloc
cartridge filters are waterproof
and effective longer than water
absorbing filters.
Getting Started
cartridge
The following customer supplied
materials should be on-hand
before beginning installation.
• Shop Towels
• Diesel Fuel (about 1 gallon)
• Thread Sealant (no thread
tapes)
• Parker Super O-Lube
(RK 31605) or equivalent
• Fuel Hose
• Mounting Hardware (3/8˝
or M10 fasteners)
• Inlet/Outlet Fittings
Contact Information
Parker Hannifin Corporation
Racor Division
P.O. Box 3208
3400 Finch Road
Modesto, CA 95353
phone 800 344 3286
209 521 7860
fax 209 529 3278
racor@parker.com
parker.com/racor
Advertisement
Table of Contents
Related Manuals for Parker Racor Turbine Series
Summary of Contents for Parker Racor Turbine Series
- Page 1 800 344 3286 • Thread Sealant (no thread 209 521 7860 tapes) fax 209 529 3278 racor@parker.com • Parker Super O-Lube parker.com/racor (RK 31605) or equivalent • Fuel Hose • Mounting Hardware (3/8˝ or M10 fasteners) • Inlet/Outlet Fittings...
-
Page 2: Mounting Information
Mounting Information 5.8 in. 5.8 in. (14.7 cm) (14.7 cm) 900FH 1000FH 4.5 in (11.4 cm) 5.0 in 11.0 in (12.7 cm) (27.9 cm) 4.5 in (11.4 cm) Adjustable to 13.5 in (34.3 cm) 10.9 in (27.7 cm) Adjustable 10° 10°... -
Page 3: Installation Instructions
Installation Instructions Before Installation Adjustable, one-piece clamp- of two 45° elbow fittings where type mounting brackets (with one 90° elbow will work. • O btain good ventilation and grade 5 fasteners) are included • W hen routing hose, avoid lighting. for ensured durability. The 900FH surfaces that move, have sharp uses one mounting bracket and • M aintain a safe working edges, or get hot (such as... -
Page 4: Element Replacement
Element Replacement Frequency of filter replacement is 2. Remove T-handle and lid. determined by the contamination 3. Remove filter by holding bail level of the fuel. Replace filter handles and slowly pulling every 10,000 miles, every 500 upward with a twisting motion. hours, every other oil change, when Dispose of properly. - Page 5 Racor Heater Relay Kit Information Recommended Racor Heater Relay Kit Heater Kits Heater In Use Use Kit Number RK11-2016 Single (1) RK 11861 12 VDC 325 Watts 27 Amps Dual (2) RK 19490-12 RK11-2015 Single (1) RK 11862 24 VDC 325 Watts 13.5 Amps Dual (2)
-
Page 6: Specifications
Specifications 900FH 900FH Maximum Flow Rate: 90 GPH (341 LPH) 7/8"-14 UNF (SAE J1926) Port Size (female threads) Min. Service Clearance: Above Assembly 7.5 in. (19.1 cm) Below Assembly 2.0 in (5.1 cm) Replacement Filter: (1 Per Assembly) (2 micron) New: 2040N-02 (Old: 2040SM-OR) (10 micron) New: 2040N-10 (Old: 2040TM-OR) -
Page 7: Replacement Parts
Replacement Parts 900FH Part No. Description T-handle and O-ring Kit RK 11-1945 (includes A) RK 11-1927-01 Lid Kit (includes B) Replacement Filter (2 Micron) New: 2040N-02 Old: 2040SM-OR (includes A & B) Replacement Filter (10 Micron) New: 2040N-10 Old: 2040TM-OR (includes A &... - Page 8 Specifications 1000FH 1000FH Maximum Flow Rate: 180 GPH (681 LPH) 7/8"-14 UNF (SAE J1926) Port Size (female threads) Minimum Service Clearance: (Above Assembly) 10.0 in. (25.4 cm) (Below Assembly) 2.0 in. (5.1 cm) Replacement Filter: (1 Per Assembly) (2 micron) New: 2020N-02 (Old: 2020SM-OR) (10 micron) New: 2020N-10 (Old: 2020TM-OR)
- Page 9 Replacement Parts 1000FH Part No. Description T-handle and O-ring Kit RK 11-1945 (includes A) RK 11-1927-01 Lid Kit (includes B) Replacement Filter (2 Micron) New: 2020N-02 Old: 2020SM-OR (includes A & B) Replacement Filter (10 Micron) New: 2020N-10 Old: 2020TM-OR (includes A &...
-
Page 10: Troubleshooting
Troubleshooting Damaged, worn, or dirty seals will allow air ingestion. Inspect and replace all seals as needed. Clean the sealing surfaces of dirt or debris every time the filter is replaced. Replace T-handle o-ring and lid Hand tighten only! Do not use tools gasket with each filter element for leverage. - Page 11 The bowl is then page. Note - Apply Parker Super The maximum fuel flow rating of drained of water at earliest O-lube (part number RK 31605) filter must not be exceeded and convenience.
- Page 12 USAGE. specifications, designs, comparable new product or availability and pricing, are repair the defective product. subject to change by Parker This express warranty shall be Warning Hannifin Corporation and inapplicable to any product not its subsidiaries at any time...