Download Print this page

Toshiba TC Series Manual

Driver
Hide thumbs

Advertisement

Quick Links

TC Series
(TCmini/TC200)
Driver
1
System Configuration....................................................................................................... 3
2
Selection of External Device ............................................................................................ 7
3
Example of Communication Setting ................................................................................. 8
4
Setup Items .................................................................................................................... 31
5
Cable Diagram ............................................................................................................... 36
6
Supported Devices......................................................................................................... 72
7
Device Code and Address Code.................................................................................... 79
8
Error Messages.............................................................................................................. 84
1
TOSHIBA MACHINE CO., LTD.

Advertisement

loading

  Related Manuals for Toshiba TC Series

  Summary of Contents for Toshiba TC Series

  • Page 1: Table Of Contents

    TOSHIBA MACHINE CO., LTD. TC Series (TCmini/TC200) Driver System Configuration....................... 3 Selection of External Device .................... 7 Example of Communication Setting ................. 8 Setup Items ........................31 Cable Diagram ....................... 36 Supported Devices......................72 Device Code and Address Code..................79...
  • Page 2 TC Series (TCmini/TC200) Driver Introduction This manual describes how to connect the Display and the External Device (target PLC). In this manual, the connection procedure will be described by following the below sections: System Configuration "1 System Configuration" (page 3)
  • Page 3: System Configuration

    TC Series (TCmini/TC200) Driver System Configuration The following table lists system configurations for connecting TOSHIBA MACHINE CO., LTD. External Devices and the Display. Series Link I/F SIO Type Setting Example Cable Diagram "Setting Example TCCMW 1" (page 8) "Setting Example "Cable Diagram 1"...
  • Page 4 TC Series (TCmini/TC200) Driver Connection Configuration • 1:1 Connection External Device Display • In this case, Display can communicate with the port on CPU module or PC link Module. • 1:n Connection (Case of using TC200 Series / TC200S Series’ External Device)
  • Page 5 TC Series (TCmini/TC200) Driver IPC COM Port When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please refer to the IPC manual for details. Usable port Usable Port Series RS-232C RS-422/485(4 wire)
  • Page 6 TC Series (TCmini/TC200) Driver DIP Switch setting: RS-422/485 (4 wire) DIP Switch Setting Description Reserved (always OFF) SIO type: RS-422/485 Output mode of SD (TXD) data: Always output Terminal resistance (220Ω) insertion to SD (TXD): None Terminal resistance (220Ω) insertion to RD (RXD): None...
  • Page 7: Selection Of External Device

    Select the manufacturer of the External Device to connect. Select "TOSHIBA MACHINE Manufacturer Co., Ltd.". Select the External Device model (series) and the connection method. Select "TC Series (TCmini/TC200)". In System configuration, make sure the External Device you are connecting is supported by Series "TC Series (TCmini/TC200)"...
  • Page 8: Example Of Communication Setting

    TC Series (TCmini/TC200) Driver Example of Communication Setting Examples of communication settings of the Display and the External Device, recommended by Pro-face, are shown. Setting Example 1 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
  • Page 9 TC Series (TCmini/TC200) Driver Settings of External Device Set PC No. of the External Device using DIP Switches and the rotary switch of External Device. Please refer to the manual of the External Device for more details. After setting, reboot the External Device to enable the setting.
  • Page 10 TC Series (TCmini/TC200) Driver Caution In the case of a 1:n connection, the terminating resistance switch and shield grounding switch need to be set. • Setting of the terminating resistance switch (ON/OFF) (LINE T) Always turn on the terminating resistance on both end stations of the communication circuit. Always turn off the terminating resistance of the way station.
  • Page 11 TC Series (TCmini/TC200) Driver Setting Example 2 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 12 TC Series (TCmini/TC200) Driver Settings of External Device Set PC No. of the External Device using DIP Switches and the rotary switch of External Device. Please refer to the manual of the External Device for more details. After setting, reboot the External Device to enable the setting.
  • Page 13 TC Series (TCmini/TC200) Driver Setting Example 3 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 14 TC Series (TCmini/TC200) Driver Settings of External Device Communication setting of External Device by ladder software (TCPRGOS-W (J)). Please refer to the manual of the External Device for more details. Procedure Start the ladder software of the computer. Select [Register editor] in the [Tool] menu.
  • Page 15 TC Series (TCmini/TC200) Driver Setting Example 4 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 16 TC Series (TCmini/TC200) Driver Settings of External Device Set PC No. of the External Device using DIP Switches and the rotary switch of External Device. Please refer to the manual of the External Device for more details. After setting, reboot the External Device to enable the setting.
  • Page 17 TC Series (TCmini/TC200) Driver Caution In the case of a 1:n connection, the terminating resistance switch and shield grounding switch need to be set. • Setting of the terminating resistance switch (ON/OFF) (LINE T) Always turn on the terminating resistance on both end stations of the communication circuit. Always turn off the terminating resistance of the way station.
  • Page 18 TC Series (TCmini/TC200) Driver Setting Example 5 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 19 TC Series (TCmini/TC200) Driver Settings of External Device Set PC No. of the External Device using DIP Switches and the rotary switch of External Device. Please refer to the manual of the External Device for more details. After setting, reboot the External Device to enable the setting.
  • Page 20 TC Series (TCmini/TC200) Driver Setting Example 6 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Set Stop Bit to 1 bit. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 21 TC Series (TCmini/TC200) Driver Settings of External Device Communication setting of External Device by ladder software (TCPRGOS-W (J)). Please refer to the manual of the External Device for more details. Procedure Start the ladder software of the computer. Select [Register editor] in the [Tool] menu.
  • Page 22 TC Series (TCmini/TC200) Driver Setting Example 7 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • For External Device, "2" is fixed for Stop Bit. For GP-Pro EX, set for Stop Bit as shown below depending on the CPU version.
  • Page 23 TC Series (TCmini/TC200) Driver Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
  • Page 24 TC Series (TCmini/TC200) Driver Setting Example 8 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • For External Device, "2" is fixed for Stop Bit. For GP-Pro EX, set for Stop Bit as shown below depending on the CPU version.
  • Page 25 TC Series (TCmini/TC200) Driver Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
  • Page 26 TC Series (TCmini/TC200) Driver Procedure On the computer, start the ladder software. From the [Tool] menu, select [Register editor]. The [Register data] window appears. Set the register as follows. Double-click [HEX] in the register column and enter the value in the [Data change] dialog box.
  • Page 27 TC Series (TCmini/TC200) Driver Setting Example 9 GP-Pro EX Settings Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • For External Device, "2" is fixed for Stop Bit. For GP-Pro EX, set for Stop Bit as shown below depending on the CPU version.
  • Page 28 TC Series (TCmini/TC200) Driver Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC] window, select the external device and click [Settings] To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add Device] to add another External Device.
  • Page 29 TC Series (TCmini/TC200) Driver 3.10 Setting Example 10 GP-Pro EX Settings Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. • Set Wait To Send to 10ms or more. Device Setting...
  • Page 30 TC Series (TCmini/TC200) Driver External Device Settings Use the ladder software (TCPRGOS-W (E)) to set up communication settings on the External Device. Refer to your External Device manual for details. After setup is complete, restart the External Device to enable the settings.
  • Page 31: Setup Items

    TC Series (TCmini/TC200) Driver Setup Items Set communication settings of the Display with GP-Pro EX or in offline mode of the Display. The setting of each parameter must be identical to that of External Device. "3 Example of Communication Setting" (page 8)
  • Page 32 TC Series (TCmini/TC200) Driver Setup Items Setup Description You can switch RI/VCC of the 9th pin when you select RS232C for SIO type. RI/VCC It is necessary to change RI/5V by changeover switch of IPC when connect with IPC. Please refer to the manual of the IPC for more detail.
  • Page 33 TC Series (TCmini/TC200) Driver Setup Items in Offline Mode • Refer to the Maintenance/Troubleshooting guide for information on how to enter offline mode or about the operation. Maintenance/Troubleshooting Guide "Offline Mode" • The number of the setup items to be displayed for 1 page in the offline mode depends on the Display in use.
  • Page 34 TC Series (TCmini/TC200) Driver Setup Items Setup Description Use an integer from 1 to 127 to enter the time (s) for which the Display waits for the Timeout response from the External Device. In case of no response from the External Device, use an integer from 0 to 255 to enter how Retry many times the Display retransmits the command.
  • Page 35 TC Series (TCmini/TC200) Driver Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device you want to set from the displayed list, and touch [Option]. Setup Items Setup Description Switches RI/VCC of the 9th pin.
  • Page 36: Cable Diagram

    TC Series (TCmini/TC200) Driver Cable Diagram The cable diagram shown below may be different from the cable diagram recommended by TOSHIBA MACHINE CO., LTD. Please be assured there is no operational problem in applying the cable diagram shown in this manual.
  • Page 37 TC Series (TCmini/TC200) Driver Display side External Device side D-sub 9 pin (socket) D-sub 9 pin (socket) Shield Signal name Signal name Display RD(RXD) SD(TXD) ER(DTR) DR(DSR) RS(RTS) CS(CTS) Shield User-created cable Display side External Device side Terminal block D-sub 9 pin (socket)
  • Page 38 TC Series (TCmini/TC200) Driver Cable Diagram 2 Display Cable Notes (Connection Port) GP3000 (COM1) GP4000 (COM1) ST (COM1) The cable length must be 15m or User-created cable LT3000 (COM1) less. PC/AT The cable length must be 15m or GP-4105 (COM1) User-created cable less.
  • Page 39 TC Series (TCmini/TC200) Driver Display side External Device side Terminal block D-sub 9 pin (socket) Shield Signal name Signal name Display RD(RXD) SD(TXD) ER(DTR) DR(DSR) RS(RTS) CS(CTS) Shield User-created cable GP-Pro EX Device/PLC Connection Manual...
  • Page 40 TC Series (TCmini/TC200) Driver Cable Diagram Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro- AGP-3302B (COM2) The cable length must face GP-4*01TM (COM1) be 500m or less.
  • Page 41 TC Series (TCmini/TC200) Driver All GP3000 models except the GP-3200 Series and AGP-3302B Only COM ports that support RS-422/485 (2 wire) communication. " IPC COM Port" (page 5) Except GP-4203T All GP4000 models except GP-4100 Series, GP-4*01TM, GP-4201T and GP-4*03T When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block Conversion Adapter, refer to Cable Diagram 3A.
  • Page 42 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (socket) Terminal Signal name Shield resistance Display 100Ω External Device side Signal name RXD+ RXD- Shell User-created cable • To insert termination resistance of 100Ω on the External Device, short-circuit jumper JP2.
  • Page 43 TC Series (TCmini/TC200) Driver Display side D-sub 9 pin (plug) Display Signal name Shield TERMRX External Device side CA4-ADPONL-01 Signal name RXD+ RXD- Shell User-created cable • To insert termination resistance of 100Ω on the External Device, short-circuit jumper JP2.
  • Page 44 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (socket) External Device side Terminal Display Shield Signal name Signal name resistance 100Ω DATA+ RXD+ DATA- RXD- GND(SG) Shell User-created cable • To insert termination resistance of 100Ω on the External Device, short-circuit jumper JP2.
  • Page 45 TC Series (TCmini/TC200) Driver Display side Terminal block External Device side Display Shield Signal name Signal name Terminal resistance RXD+ RXD- User-created cable *1 The resistance built into the Display is used as termination resistance. Please set the DIP Switch in the back of the Display as follows.
  • Page 46 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (plug) External Device side Terminal Display Shield Signal name Signal name resistance 100Ω LINE(+) RXD+ LINE(-) RXD- GND(SG) RS(RTS) Shell User-created cable • The 5V output (Pin #6) on the Display is the power supply for Siemens AG's PROFIBUS connector.
  • Page 47 TC Series (TCmini/TC200) Driver External Device side Signal name Display RXD+ RXD- Legend Name Name RJ45 RS-485 Cable (5m) by Pro-face PFXZLMCBRJR81 • To insert termination resistance of 100Ω on the External Device, short-circuit jumper JP2. • For the External Device connector, use the XH connector (XHP-7) by J.S.T. Mfg.
  • Page 48 TC Series (TCmini/TC200) Driver Cable Diagram Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro- AGP-3302B (COM2) The cable length must face GP-4*01TM (COM1) be 500m or less.
  • Page 49 TC Series (TCmini/TC200) Driver All GP3000 models except the GP-3200 Series and AGP-3302B Only COM ports that support RS-422/485 (2 wire) communication. " IPC COM Port" (page 5) Except GP-4203T All GP4000 models except GP-4100 Series, GP-4*01TM, GP-4201T and GP-4*03T When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block Conversion Adapter, refer to Cable Diagram 4A.
  • Page 50 TC Series (TCmini/TC200) Driver Display D-sub 9pin (socket) Terminal Signal name resistance Shield 120Ω Display External Device side Signal name Shell User-created cable • To insert termination resistance of 120Ω on the External Device, turn on DIP Switch SW2-7. • For the External Device connector, use the XH connector (XHP-6) by J.S.T. Mfg.
  • Page 51 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (plug) Display Signal name Shield TERMRX External Device side CA4-ADPONL-01 Signal name Shell User-created cable • To insert termination resistance of 120Ω on the External Device, turn on DIP Switch SW2-7. • For the External Device connector, use the XH connector (XHP-6) by J.S.T. Mfg.
  • Page 52 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (socket) External Device side Terminal Display Shield Signal name Signal name resistance 120Ω DATA+ DATA- GND(SG) Shell User-created cable • To insert termination resistance of 120Ω on the External Device, turn on DIP Switch SW2-7.
  • Page 53 TC Series (TCmini/TC200) Driver Display side Terminal block External Device side Display Shield Terminal Signal name Signal name resistance User-created cable *1 The resistance built into the Display is used as termination resistance. Please set the DIP Switch in the back of the Display as follows.
  • Page 54 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (plug) External Device side Display Terminal Shield Signal name Signal name resistance LINE(+) 120Ω LINE(-) GND(SG) RS(RTS) Shell User-created cable • The 5V output (Pin #6) on the Display is the power supply for Siemens AG's PROFIBUS connector.
  • Page 55 TC Series (TCmini/TC200) Driver External Device side Signal name Display Legend Name Notes RJ45 RS-485 Cable (5m) by Pro-face PFXZLMCBRJR81 • To insert termination resistance of 120Ω on the External Device, turn on DIP Switch SW2-7. • For the External Device connector, use the XH connector (XHP-6) by J.S.T. Mfg.
  • Page 56 TC Series (TCmini/TC200) Driver Cable Diagram Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro- AGP-3302B (COM2) The cable length must face GP-4*01TM (COM1) be 500m or less.
  • Page 57 TC Series (TCmini/TC200) Driver All GP3000 models except the GP-3200 Series and AGP-3302B Only COM ports that support RS-422/485 (2 wire) communication. " IPC COM Port" (page 5) Except GP-4203T All GP4000 models except GP-4100 Series, GP-4*01TM, GP-4201T and GP-4*03T When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block Conversion Adapter, refer to Cable Diagram 5A.
  • Page 58 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (socket) Terminal Signal name Shield resistance Display External Device side 100Ω Signal name RXD+ RXD- Shell User-created cable • To insert termination resistance of 100Ω on the External Device, turn on DIP Switch SW5-7.
  • Page 59 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (plug) Display Signal name Shield TERMRX External Device side CA4-ADPONL-01 Signal name RXD+ RXD- Shell User-created cable • To insert termination resistance of 100Ω on the External Device, turn on DIP Switch SW5-7.
  • Page 60 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (socket) External Device side Terminal Display Shield Signal name Signal name resistance 100Ω DATA+ RXD+ DATA- RXD- GND(SG) Shell User-created cable • To insert termination resistance of 100Ω on the External Device, turn on DIP Switch SW5-7.
  • Page 61 TC Series (TCmini/TC200) Driver Display side Terminal block External Device side Display Shield Terminal Signal name Signal name resistance RXD+ RXD- User-created cable *1 The resistance built into the Display is used as termination resistance. Please set the DIP Switch in the back of the Display as follows.
  • Page 62 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (plug) External Device side Terminal Display Shield Signal name Signal name resistance 100Ω LINE(+) RXD+ LINE(-) RXD- GND(SG) RS(RTS) Shell User-created cable • The 5V output (Pin #6) on the Display is the power supply for Siemens AG's PROFIBUS connector.
  • Page 63 TC Series (TCmini/TC200) Driver External Device side Signal name Display RXD+ RXD- Legend Name Notes RJ45 RS-485 Cable (5m) by Pro-face PFXZLMCBRJR81 • To insert termination resistance of 100Ω on the External Device, turn on DIP Switch SW5-7. • For the External Device connector, use the XH connector (XHP-8) by J.S.T. Mfg.
  • Page 64 TC Series (TCmini/TC200) Driver Cable Diagram Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro- AGP-3302B (COM2) The cable length must face GP-4*01TM (COM1) be 500m or less.
  • Page 65 TC Series (TCmini/TC200) Driver All GP3000 models except the GP-3200 Series and AGP-3302B Only COM ports that support RS-422/485 (2 wire) communication. " IPC COM Port" (page 5) Except GP-4203T All GP4000 models except GP-4100 Series, GP-4*01TM, GP-4201T and GP-4*03T When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block Conversion Adapter, refer to Cable Diagram 6A.
  • Page 66 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (socket) Terminal Signal name Shield resistance 120Ω Display External Device side Signal name Shell User-created cable • Termination resistance of 120Ω is built into the External Device. • For the External Device connector, use the XA connector (XAP-03V-1) by J.S.T. Mfg.
  • Page 67 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (plug) Display Shield Signal name TERMRX External Device side CA4-ADPONL-01 Signal name Shell User-created cable • Termination resistance of 120Ω is built into the External Device. • For the External Device connector, use the XA connector (XAP-03V-1) by J.S.T. Mfg.
  • Page 68 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (socket) External Device side Terminal Display Shield Signal name Signal name resistance 120Ω DATA+ DATA- GND(SG) Shell User-created cable • Termination resistance of 120Ω is built into the External Device. • For the External Device connector, use the XA connector (XAP-03V-1) by J.S.T. Mfg.
  • Page 69 TC Series (TCmini/TC200) Driver Display side Terminal block External Device side Display Shield Terminal Signal name Signal name resistance User-created cable *1 The resistance built into the Display is used as termination resistance. Please set the DIP Switch in the back of the Display as follows.
  • Page 70 TC Series (TCmini/TC200) Driver Display side D-sub 9pin (plug) External Device side Terminal Display Shield Signal name Signal name resistance 120Ω LINE(+) LINE(-) GND(SG) RS(RTS) Shell User-created cable • The 5V output (Pin #6) on the Display is the power supply for Siemens AG's PROFIBUS connector.
  • Page 71 TC Series (TCmini/TC200) Driver External Device side Signal name Display Legend Name Notes RJ45 RS-485 Cable (5m) by Pro-face PFXZLMCBRJR81 • Termination resistance of 120Ω is built into the External Device. • For the External Device connector, use the XA connector (XAP-03V-1) by J.S.T. Mfg.
  • Page 72: Supported Devices

    TC Series (TCmini/TC200) Driver Supported Devices Range of supported device address is shown in the table below. Please note that the actually supported range of the devices varies depending on the External Device to be used. Please check the actual range in the manual of your connecting equipment.
  • Page 73 TC Series (TCmini/TC200) Driver TC200S series This address can be specified as system data area. Device Bit Address Word Address 32 bits Notes Input Relay 1 X000 - XF7F X00W - XF7W Input Relay 2 I000 - IF7F I00W - IF7W...
  • Page 74 TC Series (TCmini/TC200) Driver TCmini series TC9-00 This address can be specified as system data area. Device Bit Address Word Address 32 bits Notes Contact Input X000 - X007 X00W - X00W External Input DIP Switch X008 - X009 Relay...
  • Page 75 TC Series (TCmini/TC200) Driver TC8-00/TC5-02 This address can be specified as system data area. Device Bit Address Word Address 32 bits Notes Photo coupler X000 - X00F X00W - X00W External Input DIP Switch X010 - X017 X01W - X01W...
  • Page 76 TC Series (TCmini/TC200) Driver TC6-00 This address can be specified as system data area. Device Bit Address Word Address 32 bits Notes Photo coupler X000 - X00F X00W - X00W External Input Push-button Relay X100 - X11F X10W - X11W...
  • Page 77 TC Series (TCmini/TC200) Driver • Please refer to the GP-Pro EX Reference Manual for system data area. Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)" • Please refer to the precautions on manual notation for icons in the table.
  • Page 78 TC Series (TCmini/TC200) Driver TC3-02 This address can be specified as system data area. Device Bit Address Word Address 32 bits Notes External Input Relay X000 - X00F X00W - X00W External Output Relay Y000 - Y00F Y00W - Y00W...
  • Page 79: Device Code And Address Code

    TC Series (TCmini/TC200) Driver Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type in data displays. TC200 series Device Code Device Device Name Address Code (HEX) Rack No. × 0x08 + Position...
  • Page 80 TC Series (TCmini/TC200) Driver TC200S series Device Code Device Device Name Address Code (HEX) Rack No. × 0x08 + Position Input Relay 1 0080 Rack No. × 0x08 + Position Input Relay 2 0081 Rack No. × 0x08 + Position...
  • Page 81 TC Series (TCmini/TC200) Driver TCmini series TC9-00 Device Code Device Device Name Address Code (HEX) Rack No. × 0x08 + Position Input Relay 1 0080 Rack No. × 0x08 + Position Output Relay 1 0082 Rack No. × 0x08 + Position 0080 Rack No.
  • Page 82 TC Series (TCmini/TC200) Driver TC6-00 Device Code Device Device Name Address Code (HEX) Rack No. × 0x08 + Position Input Relay 1 0080 Rack No. × 0x08 + Position Input Relay 2 0081 Rack No. × 0x08 + Position Output Relay 1 0082 Rack No.
  • Page 83 TC Series (TCmini/TC200) Driver TC3-01 Device Code Device Device Name Address Code (HEX) Rack No. × 0x08 + Position Input Relay 1 0080 Rack No. × 0x08 + Position Output Relay 1 0082 Rack No. × 0x08 + Position Internal Relay 0084 Rack No.
  • Page 84: Error Messages

    TC Series (TCmini/TC200) Driver Error Messages Error messages are displayed on the screen of Display as follows: "No.: Device Name: Error Message (Error Occurrence Area)". Each description is shown below. Item Description Error No. Name of External Device where error occurs. Device name is a title of External Device set Device Name with GP-Pro EX.

This manual is also suitable for:

Tcmini seriesTc200 seriesTc200s series