Clock Set Up / Select A Channel / Picture Select / Manual Channel Preset - Sharp DV-NC230S Operation Manual

Clock Set Up
VCR DVD
press
1 2 3
4 5 6
7 8 9
0 +10
PLAY
STOP
VCR/DVD COMBINATION NA527AD
This VCR/DVD incorporates a 24-hour clock. The clock must be set for the Timer
Recording function to operate correctly.
1.
Select "INITIAL".
or
Select "CLOCK".
2.
or
Select "MANUAL" or "AUTO".
3.
or
• If you select "MANUAL", continue with step 4.
• If you select "AUTO", Auto Clock Setting becomes ON. Then press
MENU to exit. The clock time will appear automatically when
you next turn the VCR mode off and on.
Select the current year.
4.
or
Select the current month.
5.
or
Select the current day.
6.
or
Select the current hour.
7.
or
Select the current minute.
8.
or
To exit the CLOCK screen.
9.
Hint
• To go back one step, press Cursor s (during the steps
• Although seconds are not displayed, they begin counting from 00
when you exit by pressing MENU. Use this feature to synchronise
the clock with the correct time.
• Repeat these steps only if either there was a power failure or this
VCR/DVD has been unplugged for more than 1 hour.
Downloaded from: http://www.usersmanualguide.com/
first.
MENU
TIMER
SET UP
B INITIAL
To decide.
INITIAL
CH TUNING
B CLOCK
LANGUAGE
To decide.
B MANUAL
AUTO
To decide.
CLOCK
B YEAR
MONTH
DAY
HOUR
To decide.
MINUTE
CLOCK
YEAR
B MONTH
DAY
HOUR
MINUTE
To decide.
CLOCK
YEAR
MONTH
B DAY
HOUR
To decide.
MINUTE
CLOCK
YEAR
MONTH
DAY
B HOUR
To decide.
MINUTE
CLOCK
YEAR
MONTH
DAY
To decide.
HOUR
B MINUTE
Auto Clock
• Channel Presetting must be set before the Auto Clock is set.
• To set the clock automatically, the channel assigned to position 01
must have the PDC signal.
• The clock cannot be set automatically if you are not receiving a
channel that carries a time signal in your area. In this case, set the
clock manually.
• Once the Auto Clock setting is performed, the VCR/DVD will correct
the current time by receiving VPS/PDC broadcasts whenever you
turn off the VCR/DVD.
• The VCR/DVD will correct the current time automatically at 8:00, if
the VCR/DVD power is turned off.
• Between 23:00~1:00, the Auto Clock function does not work even if
the VCR/DVD power is turned off.
Select a Channel
VCR DVD
press
1 2 3
4 5 6
7 8 9
0 +10
PLAY
STOP
VCR/DVD COMBINATION NA527AD
You can select a desired channel by using CH K / L or directly
pressing the Number buttons on the remote control.
Select your desired channel number.
1.
[OFF]
Hint
• Enter a channel numbers as a two-digit number for the quickest
results. For example, to select channel 6, press 0 and 6. If you only
press 6, channel 6 will be selected after a brief delay.
2005
01
• You can only select channels 1–99.
01 SA
_ _
_ _
Picture Select
VCR DVD
press
1 2 3
4 5 6
7 8 9
0 +10
PLAY
STOP
2005
VCR/DVD COMBINATION NA527AD
01
This function enables you to select the picture quality of a tape.
01 SA
_ _
_ _
Select "SET UP".
1.
2005
07
01 FR
_ _
_ _
Select "PICTURE".
2.
or
2005
07
16 SA
To switch "NORMAL", "SOFT" or "SHARP".
_ _
3.
_ _
2005
To exit the PICTURE screen.
07
4.
16 SA
01
_ _
Hint
• Once you select the Picture Select mode, it stays in effect even
after you turn off the VCR/DVD.
Manual Channel Preset
to 8).
3
VCR DVD
press
1 2 3
4 5 6
7 8 9
0 +10
PLAY
STOP
VCR/DVD COMBINATION NA527AD
Each channel is tuned manually and individually. DO NOT use
"Automatic Channel Preset" if you intend to use some of the pre-
tuned channels.
Select "INITIAL".
1.
– 12 –
first.
or
first.
B SET UP
or
To decide.
B PICTURE
B PICTURE
first.
or
B INITIAL
To decide.
MENU
TIMER
INITIAL
SET UP
AUTO RETURN [ON]
AUTO REPEAT [OFF]
[NORMAL]
SET UP
AUTO RETURN [ON]
AUTO REPEAT [OFF]
[SOFT]
MENU
TIMER
SET UP
EN