Grundfos TPE2 Installation And Operating Instructions Manual page 28
Single-stage in-line pumps with integrated variable frequency drive
Hide thumbs
Also See for TPE2:
- Installation and operating instructions manual (104 pages) ,
- Instructions manual (23 pages) ,
- Safety instructions and other important information (19 pages)
Table of Contents
Advertisement
Settings
"Operating range"
"Ramps"
"Pump number"
"Radio communication"
"Analog input 1"
"Analog input 2"
"Analog input 3"
"Built-in Grundfos sensor"
"Pt100/1000 input 1"
"Pt100/1000 input 2"
"Digital input 1"
"Digital input 2"
"Digital in/output 3"
"Digital in/output 4"
"Predefined setpoint"
"Analog output"
"External setpoint funct."
"Signal relay 1"
"Signal relay 2"
"Limit 1 exceeded"
"Limit 2 exceeded"
"Alternating operation, time"
"Time for pump changeover"
"Standstill heating"
"Motor bearing monitoring"
"Service"
"Store settings"
"Recall settings"
"Undo"
"Pump name"
"Connection code"
"Unit configuration"
* Only available if Grundfos GO is connected to a multipump system.
Alarms and warnings
"Alarm log"
"Warning log"
"Reset alarm" button
Assist
"Assisted pump setup"
"Assisted fault advice"
"Multipump setup"
28
TPE3, TPE3 D TPE3, TPE3 D
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
-
-
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
TPE3, TPE3
TPE2, TPE2
D
D
●
●
●
●
●
●
TPE3, TPE3
TPE2, TPE2
D
D
●
●
●
●
●
●
Multipump
Section
system
●
17.19 Operating range
17.25 "Ramps"
-
17.30 "Number" (Pump number)
17.31 "Radio communication"
-
(Enable/disable radio comm.)
-
-
17.10 Analog inputs
-
●
17.11 Built-in Grundfos sensor
-
17.12 Pt100/1000 inputs
-
-
17.13 Digital inputs
-
-
17.14 Digital inputs/outputs
-
●
17.21 "Predefined setpoints"
-
17.17 Analog output
-
17.20 External setpoint function
-
17.16 "Signal relay 1 and 2" (Relay
outputs)
-
●
17.23 Limit-exceeded function
●
●*
17.51 "Multipump setup" (Setup of
multi-pump system)
●*
-
17.26 "Standstill heating"
-
17.28 Motor bearing monitoring
-
17.29 "Service"
17.39 "Store settings" (Store actual
-
settings)
17.40 "Recall settings" (Recall stored
-
settings)
●
17.41 "Undo"
●
17.42 "Pump name"
●
17.43 "Connection code"
●
17.34 "Unit configuration" (Units)
Multipump
Section
system
●
17.45 Alarm log
●
17.46 Warning log
●
Multipump
Section
system
17.48 Assisted pump setup
●
17.53 Assisted fault advice
17.51 "Multipump setup" (Setup of
●
multi-pump system)
Page
43
47
48
48
36
37
38
38
39
45
41
43
40
46
51
47
47
48
49
49
49
49
49
48
Page
50
50
Page
50
54
51
Advertisement
Table of Contents
