Yamaha CinemaStation DVR-S150 Owner's Manual page 82

Setting speaker sizes (Speaker Set)
Submenu: CENTER
Sets whether the center speaker is present or not, and sets
the size of the center speaker.
Selection items: LRG (Large), SML (Small), NON
(None)
Default setting: SML
LRG: Select this setting when using a large center
speaker. The entire frequency band of the center channel
signal is output as it is from the center speaker.
SML: Select this setting when using a small center
speaker. A center channel signal with a low tone is output
from the speaker set to "BASS".
NON: Select this setting when not using a center speaker.
The center channel signal distributes the same volume
level to the front L/R speakers.
Submenu: FRONT
Sets the size of the front speakers.
Selection items: LRG (Large), SML (Small)
Default setting: SML
LRG: Select this setting when using large front speakers.
The entire frequency band of the front L/R channel signal
is output as it is from the front L/R speakers.
SML: Select this setting when using small front Speakers.
A front L/R channel signal with a low tone of is output
from the speaker set to "BASS".
Submenu: SUR.
Sets whether the surround L/R speakers are present or not,
and sets the size of the surround L/R speakers.
Selection items: LRG (Large), SML (Small), NON
(None)
Default setting: SML
LRG: Select this setting when using large surround L/R
speakers or when using surround L/R Speakers with
surround subwoofers connected by speaker cables. The
entire frequency band of the surround L/R channel signal
is output as it is from the surround speakers.
SML: Select this setting when using small surround L/R
speakers. A surround L/R channel signal with a low tone
is output from the speaker set to "BASS".
NON: Select this setting when not using surround L/R
speakers. The surround L/R channel signal distributes the
same volume level to the front L/R speakers (page 59).
Configuring Various Parameters (Set Menu)
Submenu: BASS
Selects the speaker to output a LFE/bass (low tone) signal.
LFE stands for Low Frequency Effect and it is used to
output bands of 90 Hz and below when Dolby Digital or
DTS is active.
Selection items: SWFR (Subwoofer), FRONT,
BOTH
Default setting: SWFR
SWFR: Select this setting when using a subwoofer. The
LFE and low tone sound from other channels, depending
on "CENTER", "FRONT" and "SUR." settings, are output
from the subwoofer.
FRONT: Select this setting when not using a subwoofer.
The LFE and low tone sound from other channels,
depending on "CENTER", "FRONT" and "SUR."
settings, are output from the front L/R speakers.
BOTH: Select this item to mix a low tone with a LFE
channel when using a subwoofer and independent of the
front speaker sound mode setting. The entire frequency
band of the front L/R channel is output from both the front
L/R speakers and subwoofer. Sounds can be output from
the subwoofer during 2ch or Dolby Surround playback.
Submenu: F. Level
Selects the front speaker level. When the front speaker
volume level is extremely high and out of alignment with
that of other speakers, you can lower the volume level and
adjust the balance.
Selection items: Nrm (Normal), –10 dB
Default setting: Nrm
Nrm: Usually this setting is selected.
–10 dB: Use this setting if the output level of the center
or surround speakers is out of alignment with the front
speakers. The volume level of the front speakers decreases
10 dB (about 1/3).
y
• Even if "FRONT" is set to "SML" while "BASS" is set to
"FRONT", low tones of the front L/R channel signal will be
output from the front speakers.
• If you select any DSP Program when "SUR." is set to "NON",
the CinemaStation automatically enters Virtual CINEMA DSP
mode (page 59).
• These settings are not reflected when connecting headphones.
Note
When a sampling digital signal over 48 kHz is input, some
settings may not be reflected in the playback sound.
77