Yamaha RX-V561 Owner's Manual page 55

Center speaker equalizer
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: –6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
1 SOUND MENU
D)CENTER GEQ
TEST >OFF
. 100Hz ;;;;;;
300Hz ;;;;;;
1kHz ;;;;;;
3kHz ;;;;;;
10kHz ;;;;;;
[ ]/[ ]:Up/Down
p [
[ ]/[ ]:Adjust
Test tone TEST
Use this feature to make adjustments for "CENTER GEQ"
while listening to a test tone.
Choices: OFF, ON
• Select "OFF" to stop test tones and output the currently
selected source component.
• Select "ON" to output test tones from the center and
front left speakers.
Low-frequency effect level
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: –20 to 0 dB
Control step: 1 dB
1 SOUND MENU
E)LFE LEVEL
. SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
[ ]/[ ]:Up/Down
p [
[ ]/[ ]:Adjust
Speaker SPEAKER
Adjusts the speaker LFE level.
Headphone HEADPHONE
Adjusts the headphone LFE level.
Note
Depending on the settings of "LFE/BASS OUT" (see page 49),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
D)CENTER GEQ
ON
0.0dB
0.0dB
0.0dB
0.0dB
0.0dB
E)LFE LEVEL
Dynamic range F)D.RANGE
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
1 SOUND MENU
F)D.RANGE
. SP D.R;;;;MAX
HP D.R;;;;MAX
[ ]/[ ]:Up/Down
p [
[ ]/[ ]:Adjust
Speaker SP
Adjusts the speaker compression.
Headphone HP
Adjusts the headphone compression.
Choices: MIN, STD, MAX
• Select "MIN" (minimum) if you regularly listen at low
volume levels.
• Select "STD" (standard) for general use.
• Select "MAX" (maximum) to preserve the greatest
amount of dynamic range.
Audio settings G)AUDIO SET
Use this feature to adjust the overall audio settings of this
unit.
1 SOUND MENU
G)AUDIO SET
. MUTE TYPE;;;FULL
A.DELAY;;;;;;0ms
MAX VOL.;;;+16dB
INI.VOL.;;;;;OFF
[ ]/[ ]:Up/Down
[
p
[ ]/[ ]:Adjust
Mute type MUTE TYPE
Use this feature to adjust how much the mute function
reduces the output volume (see page 36).
Choices: FULL, –20dB
• Select "FULL" to completely mute all the audio
output.
• Select "–20dB" to reduce the current volume by 20 dB.
Audio delay A.DELAY
Use this feature to delay the sound output and synchronize
it with the video image. This may be necessary when
using certain LCD monitors or projectors.
Control range: 0 to 160 ms
Control step: 1 ms
SET MENU
51
En