LEGRAND Wattstopper LMRH-101 User Manual

LEGRAND Wattstopper LMRH-101 User Manual

Dlm - digital ir handheld remote

Advertisement

Quick Links

No: 25099 – 11/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMRH-101
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
Handheld
Remote
The Wattstopper LMRH-101 Digital IR Handheld Remote uses an infrared (IR) transmitter to send commands to a Digital Lighting
Management (DLM) network. It allows the user to turn lights ON/OFF and dim without going to a wall box device.
The LMRH-101 operates on three AAA batteries. It communicates wirelessly with other DLM devices by sending an IR signal to a DLM
IR enabled device within its range and line of sight.

Battery Installation

The battery compartment holds three standard 1.5V AAA Alkaline batteries (supplied). Rechargeable NiMH batteries can be used. Do
not mix battery types. Do not mix old batteries with new batteries.

OPERATION

The LMRH-101 uses IR technology to wirelessly send control
signals to the DLM system. Point the handheld remote at any
IR-enabled DLM device within its range and press a button to send
signals to the DLM network. To identify an IR-enabled device, look
for a dark translucent lens on the face of the device.

Transmitting Range

Please refer to the top two pictures on the right.
Default Functionality: Plug n' Go™ (PnG)
As shipped from the factory, the rocker paddle controls all loads on
the DLM local network. To change the loads that are controlled by
the LMRH-101 see the ADJUSTMENT section.

Button Functions

Press the top of the rocker paddle to turn load(s) ON. The blue LED
on the paddle also turns ON. Switched loads turn ON. Dimmable
loads turn ON to the last light level set before they turned OFF.
Press the bottom of the rocker paddle to turn load(s) OFF.
Dimmable loads ramp down or up in response to pressing and
holding the top or bottom of the paddle. ON/OFF loads turn OFF
when the ramp level dims below 50%, and turn ON when the ramp
level rises above 50%.

Battery Life

To conserve battery life, the LMRH-101 shuts down 5 seconds after
the last key press unless the LMRH-101 and the DLM local network
is in configuration mode (Push n' Learn, PnL).
Wattstopper
DLM - Digital IR Handheld Remote
User Guide
Mounting
Holster

DESCRIPTION

• Single tap: Bound
• Press and hold:
• Single tap: Bound
• Press and hold:
®

SPECIFICATIONS

Power Supply .... 3 AAA batteries, 1.5V alkaline or NiMH rechargeable
Environment:
Operating Temperature ............................. 32˚to 95°F (0˚to 35°C)
Storage Temperature ............................23 to 176°F (-5° to 80°C)
Relative Humidity .............................. 5 to 95% (non condensing)
Other:
RoHS compliant
FCC part 15
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
40°
32' (10m) max.
loads turn ON to
last light level
Raise light level
loads OFF
Lower light level
Red LED
IR Lens
Configuration
Button
Point at
DLM Device

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Wattstopper LMRH-101 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for LEGRAND Wattstopper LMRH-101

  • Page 1 DESCRIPTION The Wattstopper LMRH-101 Digital IR Handheld Remote uses an infrared (IR) transmitter to send commands to a Digital Lighting Management (DLM) network. It allows the user to turn lights ON/OFF and dim without going to a wall box device.
  • Page 2 No. 25099 – 11/16 rev. 1 © Copyright 2016 Legrand All Rights Reserved. 800.879.8585 © Copyright 2016 Tous droits réservés Legrand. www.legrand.us/wattstopper © Copyright 2016 Legrand Todos los derechos reservados.

Table of Contents