Yamaha CS1X Owner's Manual page 49

PERFORMANCE
Layer 1
!
on
Layer 2
! on
Vari
Layer 3
!
on
off
Layer 4
!
Part 5
Part 16
NOTE
Reverb and Chorus send levels for Layers with the Variation
Send On/Off switch set to ON are determined by the highest
numbered Layer. For example, if Layers 1, 2 and 3 are switched on,
then the Reverb and Chorus send level for Layer 3 will determine the
amount of effect applied to each Layer.
NOTE
In Performance mode effect send levels for Parts 5~16 (as
well as Layers 1~4) can be controlled by an external MIDI sequencer.
The Variation effect cannot be applied to Parts 5~16.
Multi Play Mode
The diagram below shows the signal flow of the three effects when the
CS1x is in Multi Play mode and the Variation effect is designated as an
Insertion effect.
NOTE
In Multi Play mode the various effect settings can be
controlled by MIDI system exclusive Parameter Change messages
(received from an external sequencer or computer). The illustrations at
right show the Reverb, Chorus and Variation send parameters which
can be controlled from the CS1x panel. For details about the others,
refer to each page number as listed in the following explanation.
NOTE
When the CS1x is in Multi Play mode, the Variation Effect is
automatically reset as an Insertion Effect. If you want to set the
Variation Effect as a System Effect, you need to send a parameter
change message to the CS1x from an external MIDI sequencer.
The Variation (Insertion) effect can be applied to any one of the 16 Parts at
a time, designated by switching the Multi Edit EFFECT VARI SEND
parameter to ON (page 38). The ratio of Variation effect (wet) signal to
original (dry) signal is determined by the wet/dry balance !, which in
turn controls the amount of Variation effect signal applied to the Part
(page 38).
Although only one Part at a time can have the Variation effect applied to
it, all Parts, including the Part with Variation effect, can have Reverb and
Chorus applied, determined by the Reverb send " and Chorus send #
level settings (between 0~127) of the Multi Edit EFFECT REV SEND and CHO
SEND parameters, respectively (page 38). Reverb return $ and Chorus
return % levels can also be controlled to determine the amount of each
effect applied. The Send Chorus to Reverb & level from the Chorus effect
to the Reverb effect can also be controlled in a series, if you assign it to
the ASSIGN 1 knob (page 26); in this case, the Chorus return % level
should be set to "0".
#
(for each layer/part)
Rev Send
Rev
&
"
Rev Send
wet/dry %
Knobl (Cho to Rev)
Cho Send
'
Cho
Cho Send
(for each layer/part)
$
MULTI
•XG effect set to Insertion
•Part 3 VARI SEND set to ON
Part 1
Part 2
Out
Vari
Part 3
Part 16
The diagram below shows the signal flow of the three effects when the
CS1x is in Multi Play mode and the Variation effect is designated as a
System effect.
Each of the 16 Parts has a Dry send ! level which controls the amount of
original signal for each Part (page 38). Reverb send ", Chorus send #,
and Variation send $ levels control the amount of effect applied to each
Part, determined by the Multi Edit EFFECT REV SEND, CHO SEND and VARI
SEND parameters (between 0~127), respectively (page 38). Reverb return
%, Chorus return & and Variation return ' levels can also be controlled
to determine the amount of each effect applied (page 38).
The Send Chorus to Reverb ( level is sent from the Chorus effect to the
Reverb effect (page 38). The Send Variation to Reverb ) and Send
Variation to Chorus * levels are sent from the Variation effect to the
Reverb and Chorus effects, respectively (page 38). These three
parameters let you make series and parallel effect configurations which
provide enormous sound enhancement flexibility.
•XG effect set to System
!
Dry Send
Part 1
Part 2
Part 16
Rev Send Cho Send
" #
Vari Send, Cho Send, Rev Send = 0~127
NOTE
If you select Effect Off in the Variation Type menu, the
Layers which have the VARI SEND function set to ON will not sound.
When you don't want to use the Variation Effect on the Layers, set the
VARI TYPE to Thru.
48
Rev Return Level
Rev
Send Cho to Rev
!
wet/dry
Cho
Rev Send Cho Send
" #
Rev Return Level
Rev
(
Cho to Rev
)
Cho
Vari to Rev
Vari to Cho
*
Vari
Vari Send
$
$
&
Out
%
Cho Return Level
%
&
Cho Return
'
Vari Return
Out