Yamaha CS1X Owner's Manual page 44

ASSIGN CTRL NO (Assign Control Change Number)
This lets you assign Control Change Numbers to controllers such
as the Modulation Wheel or Sound Control Knobs. This is mainly
used to control external devices connected via MIDI.
NOTE
The main function of the Sound Control Knobs will not be
changed.
You can designate whether the Modulation Wheel or the Foot
Controller is used for Scene Control (page 16).
Control Change Number
Controller
Following are the Control Change Numbers and Names that can
be assigned to the various controllers:
Controller
Modulation Wheel
Sound Control Knob 1 (ATTACK)
Sound Control Knob 2 (RELEASE)
Sound Control Knob 3 (ASSIGN 1/DATA)
Sound Control Knob 4 (CUTOFF)
Sound Control Knob 5 (RESONANCE)
Sound Control Knob 6 (ASSIGN 2)
Footswitch connected to the FOOTSWITCH jack on the rear panel
Foot Controller connected to the FOOT CONTROLLER jack on the rear panel
Foot Volume pedal connected to the FOOT VOLUME jack on the rear panel
NOTE
In the Scene Control settings, you can choose from Mod.
Wheel (Modulation Wheel) or FootCtrl (Foot Controller).
SCENE 1 or 2 buttons (only for the Scene Control)
Assignable Control Change Numbers and Names
Control Change Number Name
1 Modulation Wheel
5 Portament Time
6 Data Entry MSB
7 Main Volume
10 Panpot
11 Expression
16 General purpose1
17 General purpose2
18 General purpose3
19 General purpose4
38 Data Entry LSB
64 Hold 1(Damper/Sustain)
65 Portament Switch
66 Sostenute
67 Soft Pedal
71 Harmonic Contents
72 Release Time
73 Attack Time
74 Brightness
84 Portament Control
91 Reverb Depth
93 Chorus Depth
94 Variation Depth
Others -------
NOTE
General Purpose: With the CS1x, General Purpose 1 is for FC,
2 for knob 3 (ASSIGN1), 3 for knob 6 (ASSIGN2) and 4 for no setting.
Name
LCD
MW
Knob1
Knob2
Knob3
Knob4
Knob5
Knob6
FS
FC
FV
Scene
LCD
Mod.Whl
PortaTm
DataMSB
MainVol
Panpot
Expres.
Generl1
Generl2
Generl3
Generl4
DataLSB
Hold1
PortaSW
Sostnut
Soft
Harmonic
RelTime
AtkTime
Bright.
PortaCt
Reverb
Chorus
Vari
-------
43
Assigning the Controllers
1.Move the controller on the panel to which the Control Change
Number is to be assigned. The parameters of the controller
will appear in the LCD.
NOTE
Press the SCENE1 or SCENE 2 button to display the Scene
Control parameters.
2.Press the Parameter Value UP/DOWN button to select the
Control Change Number and Name.
3.Repeat steps 1 and 2 to assign the Control Change Numbers
and Names to each controller.
NOTE
This function is convenient for controlling an external MIDI
device with the CS1x. For details, see page 53.
Tips About the Sound Control Knobs
The changes made by the Sound Control Knobs can be output as
the MIDI messages.
The MIDI messages output via MIDI OUT can be assigned using the
ASSIGN CTRL NO function shown at the left.
The assignments set at the factory:
Sound Control Knob 1 73: Attack Time
Sound Control Knob 2 72: Release Time
Sound Control Knob 3 17: General purpose2
Sound Control Knob 4 74: Brightness
Sound Control Knob 5 71: Harmonic Contents
Sound Control Knob 6 18: General purpose3
• When the CS1x receives the data assigned to each Knob from an
external MIDI device, the parameter printed on the panel for the
Knob will be affected. For example, the Attack Time will be affected,
when the Brightness (74) is assigned to the Knob 1 and the Attack
Time (73) is assigned to the Knob 3, and then the message for the
Brightness (74) are transmitted from an external device.
• Both data assigned to the Knob using the ASSIGN CTRL NO
function and Knob data which parameter name is printed on the
panel are sent to the internal tone generator when turning the
Knob. For example, both Brightness (74) and Attack Time will be
affected when the Brightness (74) is assigned to the Knob 1 and the
Knob 1 is turned.