Yamaha CBX-K1 Owner's Manual page 23

Explanation
Stop command for sequencer/rhythm machine.
Continue command for sequencer/rhythm machine.
Start command for sequencer/rhythm machine.
Tempo entry for sequencer/rhythm machine. Setting this to 0 disables the MIDI clock transmission.
When ASSIGNABLE Wheel is set to Tempo (cntrl. no. 148), this is inactive.
This allows selection of voice banks on tone generators that support multiple banks. The bank select
message must include both MSB and LSB values.
This allows entry of program numbers. Stepping up or down through program numbers is also possible
by holding down C and using the N / M buttons; see page 10.
This resets the connected tone generator to General MIDI operation. WARNING: Be careful when using
this, since it automatically changes whatever settings you've made on the tone generator. (Only GM-
compatible tone generators respond to this message.)
This turns all sounds off over the current MIDI channel. To turn all sounds off for all MIDI channels,
use All Sound Off in Group B.
This resets the connected tone generator to XG operation. WARNING: Be careful when using this, since
it automatically changes whatever settings you've made on the tone generator. (Only XG-compatible tone
generators respond to this message.)
When set to ON, this merges all data received at MIDI IN with the data generated by the CBX-K1. Merge
can be set independently for each channel in the Group B functions.
This determines the MIDI transmit channel for the CBX-K1. This should be set to match the MIDI
receive channel of the connected MIDI device.
This sets a fixed velocity value for the keyboard; in other words, playing the keyboard at any strength
results in a certain velocity value. When this is set to 0 (initial touch on), Touch Sensitivity can be set in
the Group B functions. When ASSIGNABLE Wheel is set to Velocity (147), this is inactive.
This determines the RPN (Registered Parameter Number) for the ASSIGNABLE Wheel. This function
should be used for all RPN's not listed on the panel. The message must include both MSB and LSB
values.
This determines the Controller Number for the ASSIGNABLE Wheel. Though not all are listed on the
panel, any of the standard Control Change numbers (0 -119) can be assigned. The RPN, NRPN and
Others numbers on the panel can also be assigned here.
This determines the NRPN (Non-Registered Parameter Number) for the ASSIGNABLE Wheel. This
function should be used for all NRPN's not listed on the panel. The message must include both MSB
and LSB values.
This determines the drum number for use with the drum-related controller numbers (131-141).
This lowers the key transposition by the specified amount (in semitones).
This raises the key transposition by the specified amount (in semitones).
Footnotes
*1 For toggle (on/off) switch functions, the V /
B lamps blink rapidly when the function is set
to ON, and flash once when it is set to OFF.
*2 To send a specific value for the current control number
assignment of the Wheel, hold down C, enter the
desired value, and press L. However, this cannot
be done with controller numbers 143 (Polyphonic Key
Pressure), 147 (Velocity), or 148 (Tempo).
Range (Hexadecimal
in parentheses)
—
—
—
0, 20-300 (0, 14-12C)
(0: MIDI clock off)
MSB: 000-127 (00-7F)
LSB: 000-127 (00-7F)
0-127 (0-7F)
—
—
—
ON, OFF
1-16 (1-10)
0, 1-127 (0, 1-7F)
MSB: 000-127 (00-7F)
LSB: 000-127 (00-7F)
0-148 (0-94)
MSB: 000-127 (00-7F)
LSB: 000-127 (00-7F)
0-127 (00-7F)
0-12 (0-C)
0-12 (0-C)
*3 Transpose can be done in two ways: by repeatedly
pressing the appropriate TRANSPOSE key or by
entering the transpose value directly after pressing the
appropriate TRANSPOSE key. To restore the normal
transpose setting, hold C and press both
G / H keys simultaneously.
Group A Functions
Default MIDI Code
Setting
— <<FC>>
— <<FB>>
— <<FA>>
120 <<F8>>
— <<Bn 00 msb, Bn 20 lsb, Cn pp>>
0 <<Cn pp>>
— <<F0 7E 7F 09 01 F7>>
— <<Bn 78 00>>
— <<F0 43 ls 4C 00 00 7E 00 F7>>
ON —
1 —
0 —
— <<Bn 64 lsb, Bn 65 msb, Bn 06 vv>>
1 <<Bn gg vv>>
— <<Bn 62 lsb, Bn 63 msb, Bn 06 vv>>
0 —
0 —
0 —
19