Table of Contents
Advertisement
Appendix
5. MIDI format details
5.1. NOTE OFF (8n)
< Reception >
Received when [Rx CH] matches.
Used to control effects. Refer NOTE ON for details.
STATUS
1000nnnn 8n
DATA
0nnnnnnn nn
0vvvvvvv vv
5.2. NOTE ON (9n)
< Reception >
Received when [Rx CH] matches.
Used to control effects. Refer below for details.
Velocity of 0x00 is equivalent to Note-Off.
STATUS
1001nnnn 9n
DATA
0nnnnnnn nn
0vvvvvvv vv
* Effect control by Note
1: Dynamic Flange/Dynamic Phase/Dynamic Filter
When the SOURCE parameter is set to MIDI, the note velocity (both
note-on and note-off) is used to control the Modulation frequency
width.
5.3. CONTROL CHANGE (Bn)
< Reception >
Control change messages will be received if the [Control Change
Mode] is RX or TX/RX and the [MIDI Rx Ch] matches. However if
[MIDI Rx Ch] is ALL, this message is received regardless of the chan-
nel.
< Transmission >
If [Control Change Mode] is TX or TX/RX, control change messages
will be transmitted on the [MIDI Tx Ch] channel when you operate a
parameter.
STATUS
1011nnnn Bn
DATA
0ccccccc cc
0vvvvvvv vv
The control value is converted into a parameter value according to
the following equation.
S= total number of steps in the parameter's variable range
128 / S = X remainder Y
INT((Y+1)/2) = Z
If (MIDI DATA - Z) < 0, then Value = 0
If ((MIDI DATA - Z)/X) > MAX, then Value = MAX
Otherwise, Value = INT ((MIDI DATA -Z)/X)
5.4. PROGRAM CHANGE (Cn)
< Reception >
Program change messages will be received if the [Program Change
Mode] is RX or TX/RX and the [MIDI Rx Ch] matches. However if
[MIDI Rx Ch] is ALL, this message is received regardless of the chan-
nel.
A scene memory will be recalled according to the [PROGRAM
CHANGE TABLE] settings.
< Transmission >
If [Program Change Mode] is TX or TX/RX, a program change will
be transmitted on the [MIDI Tx Ch] according to the [PROGRAM
CHANGE TABLE] settings when you recall a memory number. If the
recalled memory number has been assigned to more than one pro-
gram number, the lowest-numbered program number will be trans-
mitted.
STATUS
1100nnnn Cn
DATA
0nnnnnnn nn
206
Note Off Message
Note No.
Velocity ( ignored)
Note On Message
Note No.
Velocity ( 1-127:On, 0:off)
Control Change
Control No. (0-95, 102-119)
Control Value (0-127)
Program Change
Program No. ( 0-127)
5.5. MIDI TIME CODE QUARTER FRAME (F1)
< Transmission >
If [MIDI OUT] is set to MTC, Quarter Frame messages will be trans-
mitted according to the time code movements of the recorder when
the recorder is playing or recording.
< Reception >
This message is received if [MTC SYNC MODE] is set to SLAVE.
Quarter Frame messages received in realtime are internally assem-
bled into time code that controls the recorder.
Quarter Frame Message
STATUS
11110001 F1
nnn = message type (0-7) dddd = data
DATA
0nnndddd dd
5.6. SONG POSITION POINTER (F2)
< Transmission >
If [MIDI OUT] is set to CLK, a song position message will be trans-
mitted when STOP or LOCATE is performed on the recorder, to
indicate the song position from which the song should start at the
next START or CONTINUE message.
Song Position Pointer
STATUS
11110010 F2
data( H) high 7 bits of 14 bits data
DATA
0ddddddd dd0
data( L) low 7 bits of 14 bits data
0ddddddd dd1
5.7. TIMING CLOCK (F8)
< Transmission >
If [MIDI CLK] is ON, this message is transmitted according to the
MIDI Tempo Map from when the recorder begins playing or record-
ing, until it stops.
Timing Clock
STATUS
11111000 F8
5.8. START (FA)
< Transmission >
If [MIDI CLK] is ON, this message is transmitted when the recorder
begins playing or recording at a location other than the first measure.
Start
STATUS
11111010 FA
5.9. CONTINUE (FB)
< Transmission >
If [MIDI CLK] is ON, this message is transmitted when the recorder
begins playing or recording at a location other than the first measure.
Continue
STATUS
11111011 FB
5.10. STOP (FC)
< Transmission >
If [MIDI CLK] is ON, this message is transmitted when the recorder
stops.
Stop
STATUS
11111100 FC
5.11. ACTIVE SENSING (FE)
< Reception >
Once this message is received, subsequent failure to receive any mes-
sage for a period of 300 ms will cause Running Status to be cleared,
and MIDI communications to be initialized.
Active Sensing
STATUS
11111110 FE
5.12. RESET (FF)
< Reception >
When a Reset message is received, MIDI communications will be ini-
tialized by clearing Running Status etc.
Reset
STATUS
11111111 FF
5.13. EXCLUSIVE MESSAGE (F0-F7)
5.13.1. MMC
5.13.1.1. MMC STOP
< Transmission >
When the STOP key is pressed, this message is transmitted with a
device number of 7F.
Advertisement
Table of Contents
