Early Childhood Resources ELR-0635 Manual

20-Tray Storage Cabinet
Model No. ELR-0635
Mount Laurel,NJ 08054 USA
www.ecr4kids.com
A2
A1
E
E
C2
E
B
C1
C2
F
D
F
D F
F
BEFORE ASSEMBLING,
MAKE SURE THERE
ARE NO
MISSING PARTS.
TIGHTEN SCREWS
PARTS LIST
UNTIL ALL SCREWS
A1
HAVE BEEN LOOSELY
Left Side Panel
A2
Right Side Panel
B
!
Top Shelf
C1
Middle Shelf(1)
C2
Middle Shelf(2)
- Adult Assembly Required. Two
D
adults recommended.
Bottom Shelf
E - Contains small parts, sharp points
Back Panel(5)
and edges.
F
Divider(4)
- Do not stand, sit, kneel, climb, lean
G
Large Hex Screw(20)
or pull on unit for support.
H
- Never leave children unattended.
Metal Dowels(8)
- Do not place unit near high heat or
I
Hex Key Tool
moisture.
J
- Adult Supervision Recommended.
Wheel Casters(4)
K
Caster Screws(16)
L
Cams(8)
1
B
E
A1
E
Ｘ８
L
A2
TIP！
1A. Place the Top Shelf(B) top-down on a carpet or protected surface.
DO NOT FULLY
Insert 8 Metal Dowels(H) into the plastic plugs located underneath
the Top Shelf(B). Tighten with a Phillips Head Screwdriver.
1B. Insert 2 Cams(L) into the large holes in each of the Dividers(F).
POSITIONED。
Make sure the arrows on Cams(L) point toward the holes in the closest
edge.
1C. Position the Top Panel(B) so the attached Metal Dowels(H) enter the
WARNING:
holes in the top edge of the Dividers(F). Turn Cams(L) with a Phillips
Head Screwdriver until locked onto the Metal Dowels(H).
2

Insert the Back Panels

2. Slide the Back Panels(E) into the grooves between the Dividers(F)
until fully inserted into the slot as shown.
E
F

Attach the Dividers to the Top Shelf

B
H
F
F
F
F
B
H
TIP:
E
- If the Back Panel does
E
not slide easily into the
E
grooves, wiggle the Back
E
while pushing the panel
F
into the slot.
F
- You may also turn the
F
rear Cams on the shelf
above or below to unlock,
push the Back until fully
inserted into the slot, then
turn Cams to the locked
B
position again.
3

Insert the Middle Shelves

Ｘ８
H
C2
C1
C2
F
B
F
E
F
E
E
4
Attach the Divider Section to
the Base
F
F
F
F
5

Attach the Wheel Casters

5. Beginning with the holes on the inside of the Wheel Caster(J) mount
plate (opposite the kickplate on Base(D)), attach the 4 Wheel Casters(J)
using 16 Caster Screws(K). Tighten with a Phillips Screwdriver.
K
J
D
C2
C1
C2
F
B
Version: ELR-0635.D.2010.01.04
3A. Two Adults Suggested:
Carefully lay the unit down
on its back. Insert a Middle
Shelf(C2) into the bottom slots
on the Dividers(F) as shown
until fully inserted.
3B. Insert a Middle Shelf(C1)
into the middle slots on the
F E
Dividers(F) as shown until
E
fully inserted.
3C. Insert a Middle Shelf(C2)
into the top slots on the
Dividers(F) as shown until
fully inserted.
4A. Two Adults
G
Suggested:
Carefully turn the
unit upside down to
Ｘ８
D
G rest on Top Shelf(B).
4B. Attach the Base
to the Divider
C2
Section(F,E,C1,C2)
C1 using 8 Large Hex
Screws(G). Tighten
C2
with the Hex Key
B
Tool(I).
Caster
Screw
Ｘ１６ Ｘ４
Mount
J
K
Plate
Attach
First