Related Manuals for Hussmann SHVSV Series
Summary of Contents for Hussmann SHVSV Series
- Page 1 032018 /SPECIALTY SHVSV BAKERY SERVICE MERCHANDISER U S E R M A N U A L SHVSV - SHVSV-DWR-3-R - SHVSV-DWR-4-R - SHVSV-DWR-8-R - SHVSV-DWR-10-R Remote - SHVSV-DWR-45IS-R...
-
Page 2: Table Of Contents
Remove Rear Raceway Electrical Conduit (Electrical Box) Electrical Wiring Diagram DOE 2012 Hussmann refrigerated merchandisers con gured for sale for use in the United States Energy E ciency meet or surpass the requirements of the DOE 2012 energy e ciency standards. Compliant... -
Page 3: General Information
Shortages: Check your shipment for any possible shortages of material (See Parts List page 9). If a shortage should exist and is found to be the responsibility of Hussmann Chino, notify Hussmann Chino. If such a shortage involves the carrier, notify the carrier immediately, and request an inspection. -
Page 4: Case Sections
Case Sections SHVSV-DWR 13 1/4" 22" 24" 10" 29 1/2" 26" 26" 51 3/4" 9 7/8" CLEAR 30 1/4" SLIDE-OUT DECK 20 1/4" 15" +3" RAISED BASE 5 1/8" 2" 36 3/8" 38 3/8" REAR OF CASE (SERVER SIDE) 3 1/2" 3 1/2"... -
Page 5: Installation
Installation (Unloading) Receiving Case NOTICE Upon receiving your new Hussmann Case all equip- ment should be thoroughly examined for shipping damage before and during unloading. This equipment Do NOT remove Foam Blocks from shelves has been carefully inspected at our factory. Any claim and glass until the merchandisers are for loss or damage must be made to the carrier. -
Page 6: Lifting And Transport
Installation (Cont’d) SHVSV Lifting and Transport 5. The SHVSV merchandiser can be raised at one Instructions end underneath the deck with a forklift or J-Bar if 1. The SHVSV can be lifted by a forklift using the skid forklift is not accesible to allow the placement of which the merchandiser is mounted to. -
Page 7: Skid Removal
Installation (Cont’d) Skid Removal Hardware Removal Remove screws as well as fastened plates bolted to Important: See lifting instructions to properly lift case each 2x4 board at each base leg. when being placed on dollies or permanent location. (See page 6 for Lifting Instructions.) Lifting Points Leave all hardware and fi... -
Page 8: Level Case
Installation (Cont’d) Level Case Position the case at the highest point. Set a long magnetized level (4ft [1220 mm] or more) on either underneath the deck or on top of the case. Ensure to level case from front to back and side to side. -
Page 9: Joint Trim Pack List
----------------- + ------------- &! ----------------- &# & -- --#-- '--- &. &. ! " # " # % " # & & ' " ! * " ! " " ! &. $" &" " # %" ( &. # % ( & %"... -
Page 10: Setting And Joining
Installation (Cont’d) Setting and Joining Snapping Chalk Lines The sectional construction of these models enable Prepare permanent positioning by marking fl oors them to be joined in line to give the effect of one con- with Chalk snap lines where cases are to be located. tinuous display. - Page 11 Installation (Cont’d) Setting STEP 2. Set fi rst case over the highest part of STEP 1. Using case blueprints, measure off and the fl oor and adjust legs so that case is level. mark on the fl oor the exact dimensions of where the cases will sit.
- Page 12 Installation (Cont’d) STEP 4. Apply liberal bead of case joint sealant STEP 6. To compress butyl at joint, use two (Silicone) to fi rst case. Sealant area is shown in Jurgenson wood clamps. Make sure case is illustration. Apply heavy amount to cover entire level from front to back and side to side on inside shaded area.
-
Page 13: Glass Adjustment
Installation (Cont’d) SHVSV Glass Adjustment Glass must be parallel to ledge when viewed from front. Glass height should be level with front ledge as demonstrated below. Follow these steps accordingly to properly and safely adjust the position of the front glass. BEFORE ADJUSTING GLASS •... - Page 14 Installation (Cont’d) SHVSV Glass Adjustment Loosening Torx Screws behind underside of glass clamp will allow adjustments to glass from side to side. Post adjustments, tighten Torx Screws to secure glass in place. Torx Screws SHVSV Glass Clamp Adjustment Loosening Torx Screws underneath the Pivot Arm will allow adjustments to Glass Clamp from side to side.
-
Page 15: Body Panels Install
Installation (Cont’d) Front Body Panel Install and Removal Fasten Rear Body Panel Install (1) Align placement hooks of case with slots on No tools will be needed to install body panels. panel. (2) Slide top panel slots into placement hooks To begin bottom panel assembly, place the front and lay fl... -
Page 16: Refrigeration
If in the case pressure was sealed at factory already. Seal both the inside not maintained, contact your Hussmann Service and outside. We recommend using an expanding Tech for further assistance. -
Page 17: Refrigerant Spec Sheet
Refrigeration Spec Sheets BAKERY SERVICE VERTICAL GLASS WITH DRAWER REVISION DATE 03/05/18 HUSSMANN - SHVSV-DWR (CHINO) REAR OF CASE (SERVER SIDE) 3 1/2" 3 1/2" 3 1/8" 13 1/4" 22" 8" 1 3/8" 1 3/8" ELECT REFRIG. 20" 24" 6"... -
Page 18: Electrical
Electrical Field Wiring Merchandiser Electrical Data Field wiring must be sized for component am- Technical data sheets are shipped with this peres stamped on the serial plate (refer to pg 16 manual. The data sheets provide merchandiser for location). Actual ampere draw may be less electrical data. -
Page 19: Remove Rear Raceway
Electrical Cont’d Remove Rear Raceway Electrical Conduit (Electrical Box) The merchandisers electrical access is located The merchandisers electrical conduit can be at the rear of the case. Fasteners must be re- found inside the compartment at the rear. Re- moved in order to gain access. See illustration moving the raceway will gain access to the elec- below. -
Page 20: Electrical Wiring Diagram
% & # $ # )! % & , # %! , # ! !. *#+ )###%$ & & ) , # *#+ )###%$ & & ) , # 0 !% 0 !% & 0 .# % & !"... - Page 21 %& 1 &% ( % & - # ! !! *!+ (###%, & & ( - # *#+ (###%, & & ( - # 1 (/ 1 !% 1 !$ %& !"...
- Page 22 %%&' # ) # $ " 2 !) + 2 !) + -#. &###)$ -#. &###)$ & / # & / # -#. #& -!. &###)$ 2 !) 2 !) & / # 2 & -!. &###)$ 2 & & / # #&) #&) 2 &...
- Page 23 & 0 '1 .! % 0 '1 .! % *#+ '###$( % , # *#+ '###$( ' , # ' , # ( , # ! !# % , # 345 0 !$ ! !% 0 !$ *!+ '###$( ' , # *!+ '###$( ' , # 0 ! .
- Page 24 $$& *! + ) . # & &! . # ,#- #* ! !* ,)- *###+% * . # ,#- *###+% * . # & & 1 %* 1 !+ & & 1 &# $$& !"...
-
Page 25: User Information
User Information Start Up Load Limit See the merchandisers Data Sheet Set for refrig- Each Merchandiser has a load limit. Shelf life of erant settings and defrost requirements. Bring perishables will shorten if load limit is violated. merchandisers down to the operating tempera- tures listed on the Data Sheet. -
Page 26: Maintenance
Maintenance Case Cleaning Clean frequently to avoid build-up of hard, stub- Long life and satisfactory performance of any born stains. A stainless steel cleaning solution equipment are dependent upon the care it re- may be used periodically to minimize scratching ceives. - Page 27 Maintenance Cont’d • Remove the product and all loose debris to avoid clogging the waste outlet. • Store product in a refrigerated area such as a cooler during the cleaning process. Remove only as much product as can be taken to the cooler in a timely manner.
-
Page 28: Troubleshooting
Troubleshooting Problem Possible Cause Possible Solution Case temperature is Ambient conditions may Check case position in store. Is the case located near an too warm. be affecting the case open door, window, electric fan or air conditioning vent that operation. may cause air currents? Case must be located minimum 15 Ft away from doors or windows. - Page 29 Troubleshooting Cont’d Problem Possible Cause Possible Solution Water has pooled Case drain is clogged. Clear drain. under case. PVC drains under case Repair as needed. may have a leak. Case tub has unsealed Seal as needed. opening. If the case is in a line- Install case to case joint and seal as needed.
- Page 30 August 31, 2018 This warning does not mean that Hussmann products will cause cancer or reproductive harm, or is in violation of any product-safety standards or requirements. As clarified by the California State government, Proposition 65 can be considered more of a ‘right to know’...
- Page 31 To obtain warranty information or other support, contact your Hussmann representative. Please include the model and serial number of the product. Hussmann Warranty / Technical Assistance (800) 592-2060 Hussmann Corporation, Corporate Headquarters: Bridgeton, Missouri 63044 2014...