Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pronomic Lift&Drive 325P+
Summary of Contents for Pronomic Lift&Drive 325P+
- Page 1 Lift trolley Lift&Drive 325P+ Original instructions...
- Page 2 It is important that you read and understand the manual before using the lift trolley. Do you have any questions? – Please contact the distributor or the manufacturer. Pronomic AB Visiting address: Postal address: Domherrevägen 15 Box 5504 192 55 Sollentuna...
-
Page 3: Table Of Contents
Contents Description of the lift trolley ....................4 Warranty ............................4 Components ..........................4 Assembly ..........................6 Disassembly and scrapping ......................6 Using the lift trolley ......................7 Handlebar ............................ 7 Remote control ..........................7 Power pack ..........................8 Brakes ............................8 Directional lock .......................... -
Page 4: Description Of The Lift Trolley
Damage due to misuse or incorrect use of the equipment will void the warranty. 1.2 Components The lift trolley consists of a number of modules. The locations of these are shown in the image on the next page. Please contact Pronomic for information regarding part numbers. ... - Page 5 ________________________________________________________________________________ 5 – Lift trolley Lift&Drive 325P+...
-
Page 6: Assembly
To disassemble the lift trolley, follow the instructions in section Assembly, but in reverse order. When the lift trolley is due for scrapping the machine, complete with batteries, should be handed in to a recycling centre or Pronomic to ensure reuse and safe handling of all parts. ________________________________________________________________________________... -
Page 7: Using The Lift Trolley
Using the lift trolley If the load is left on the lifter for some time it may be necessary to lower the load before it can be raised. 3.1 Handlebar To achieve a good working position the handlebar should be adjusted to a correct height. The handlebar can easily be adjusted in height by loosening the black knobs on the handlebar. -
Page 8: Power Pack
The remote control should be placed to allow the user to easily press the buttons or to control the lever. The bracket for the remote control is fitted to the handlebar. The bracket can easily be moved by turning the black knob counter-clockwise. The bracket can be locked in any position on the handle by turning the knob clockwise. -
Page 9: Loading And Unloading
Further use requires more frequent service intervals. Only spare parts supplied or approved by Pronomic may be used. After disassembly/assembly of the column or load carrier a load test should be performed, see section Assembly. -
Page 10: Every Year, Or When Needed
On the power pack a flashing bar on the voltage indicator means that the batteries need charging. The lift trolley will not perform a lift while the voltage indicator are flashing. If the lift trolley is left unused for about 10 minutes sleep mode is activated and the voltage indicator turns black. The lift trolley is restarted by pressing any button on the remote control. -
Page 11: Wheels
5.2.6 Wheels Make sure all wheels run smoothly. Lubricate the bearings. Check that the tire rubber is intact. 5.2.7 Brakes Check that the breaks work. 5.2.8 Knobs for handlebar and bracket for remote control Check that the knobs loosen and tighten correctly. 5.2.9 Replacing the fuse The fuse is located inside the power pack. -
Page 12: Plates And Decals
If problems arise, some guidance is provided below. If the problem persists after action has been taken – Please contact service technician or Pronomic. If the load carrier does not move at all, or very slowly: •... -
Page 13: Technical Specifications
• Check the battery voltage and replace batteries if the voltage after 8 hours of charging is less than 25 volts. If the lift trolley sounds strange: • Make sure the lift trolley is correctly assembled, see section Assembly. • See section Maintenance. Technical specifications Model Lift&Drive 325P+... -
Page 14: Ec Declaration Of Conformity Of The Machinery
Safety of machinery - Minimum gaps to avoid crushing of parts of the human body We hereby declare that the above-referenced machine is in conformity with stated directives and standards. Sollentuna, 2018-04-24 ………………………………………………………… Joakim Stannow, CEO, PRONOMIC AB ______________________________________________________________________________________ The lift trolley has been modified and/or equipped with attachments as follows: ……………………………………………………………………………………………………………………………………………………………………….……. ……………………………………………………………………………………………………………………………………………………………………….……. - Page 15 ________________________________________________________________________________ 15 – Lift trolley Lift&Drive 325P+...
- Page 16 Distributed by: ________________________________________________________________________________ 16 – Lift trolley Lift&Drive 325P+...