Advertisement
Quick Links
U5042A PAG PULSAR INSTRUCTION MANUAL
PAG Pulsar
All-Chemistry Charging System
Instruction Manual
CONTENTS
SECT ION
1
SAFETY
2
3
4
5
6
1.1
1.2
1.3
1.4
1.5
1.6
1.7
PAGE
1.8
2
1.9
1.10 Refer all servicing to qualified service personnel. Servicing is required
3
6
6
1 2
1 3
1
U5042A PAG PULSAR INSTRUCTION MANUAL
SECTION 1
SAFETY
This manual contains important safety and operating instructions.
Read these fully and note all warnings before using the charger.
Please follow all instructions and retain this manual for future reference.
PAG Pulsar chargers are not intended for any use other than the charging
of batteries as detailed in Section 2 - 'Specification' .
IMPORTANT: Use only on AC supplies 100-250V, 50/60Hz.
Supply connection to the unit should be made using only the standard
lead supplied with this equipment.
Protect the power cord from being walked on or pinched, particularly at
plugs. Unplug this apparatus during lightning storms or when unused for
long periods of time.
Ensure that the ventilation slots are not obstructed when in use, e.g. do
not site the charger on a deep pile carpet, or cover when in use.
WARNING: Indoor use only. To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
Although the charger is reverse polarity and short circuit protected,
extreme care should always be taken not to short circuit the battery
itself. Rechargeable batteries can deliver power at a very high rate, and
short circuiting even a partially charged battery could result in a fire or
personal injury. PAG supplies a range of connector leads for most charging
requirements, and does not accept responsibility for any other form of
charging connection.
Do not disassemble the charger. There are no user-serviceable parts
inside. Incorrect re-assembly may result in a safety hazard.
Double Insulation: When servicing use only identical replacement parts.
when the apparatus has been damaged in any way, such as supply cord or
plug is damaged, liquid has been spilled, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped. In
this event you should seek advice from your nearest PAG Dealer, or from
PAG USA by telephoning 818 760 8265, or direct from PAG Ltd., London,
by telephoning +44 (0)20 8543 3131.
2
Advertisement
Related Manuals for PAG Pulsar 9795
Summary of Contents for PAG Pulsar 9795
-
Page 1: Table Of Contents
Read these fully and note all warnings before using the charger. Please follow all instructions and retain this manual for future reference. PAG Pulsar chargers are not intended for any use other than the charging of batteries as detailed in Section 2 - 'Specification’ . -
Page 2: Specification
Main Charge program, which will run ◗ Nickel-Cadmium batteries having nominal voltages of between 4.8V and until the battery is fully charged. This program also recovers PAG Li-Ion batteries which have been over-discharged to the point where the internal 14.4V, and nominal capacities of between 1Ah and 10Ah. -
Page 3: Installation
This switch also provides for the selection of programs and interrogation of charge and discharge data. All PAG Pulsar chargers are fitted with a mains input socket conforming to CEE22 (IEC socket). This is situated on the back panel. Mains supply 2.14 Safety:... - Page 4 Hold in 6 seconds with battery connected: selects battery interrogation between 2Ah and 10Ah. feature (Snap-On compatible connectors only). NOTE: PAG intelligent batteries automatically over-ride the Auto Mode or Hold in 12 seconds with battery connected to Snap-On compatible Manual selection, and control their own charge regime.
- Page 5 Press the Function button twice. The screen will indicate the selection and NOTE: All PAG Pulsar chargers offer a choice of connector on each channel. any further operation of the button will move the recovery indication to the Batteries may be connected to either but not both connectors at the same next channel.
-
Page 6: Servicing & Repairs 1
To the charger there is no difference between a disconnected battery and one 818 760 8265 or direct from PAG Ltd., London, by telephoning +44 (0)20 8543 that is open circuit. If the charger indicates that a battery is disconnected 3131. -
Page 7: Warranty 1
In the event of failure of a product covered by this warranty, PAG Limited will repair and calibrate equipment returned to an authorised Service Facility within the period of the warranty, provided the warrantor’s examination discloses to its satisfaction the product was defective.