A Fter C Leaning; C Lean S Urge B Utton; Picking Up Spills - Hoover BRUSH N WASH Instructions Manual

a. Allow carpet or upholstery to dry. To
A A f f t t e e r r c c l l e e a a n n i i n n g g
help prevent matting and resoiling the
from surface until it is completely dry. If
carpet, keep children and pets away
it is necessary to walk on damp car-
pet, place towels or white cloths on the
traffic areas.
If furniture must be replaced before the
carpet is dry, use plastic or aluminum
foil pads under legs of furniture so metal
slides or wood finishes will not stain the
b. If desired, the carpet may be rinsed.
carpet.
Rinsing is not necessary for cleaning,
but it may Improve the surface's appear-
ance after it is dry.
If rinsing is desired, be careful not to
Allow time for carpet or upholstery to
over-wet the carpet or upholstery.
dry completely between cleaning and
rinsing. To rinse, follow the same proce-
dure for cleaning only using hot tap
water (50˚ C max) with no detergent in
the upper clean solution tank.
Step on handle release pedal and
lower handle to operating position;
turn carpet cleaner ON.
ing solution and slowly push carpet
5. Squeeze trigger to release clean-
cleaner forward (equals one wet
stroke).
slowly pull carpet cleaner back
6. Continue to squeeze trigger and
toward you (second wet stroke).
Release trigger and slowly push car-
pet cleaner forward over area just
Then slowly pull carpet cleaner
sprayed with solution (dry stroke).
back toward you without squeezing
trigger (dry stroke).
7. Overlap strokes by 1 inch to help
prevent streaking.
Keep nozzle flat on floor for both for-
ward and reverse strokes.
8. For heavily soiled areas, repeat
steps 5-7.
9. For particularly soiled carpet or
spots, use the Clean Surge™ button
(see following section). Avoid satu-
Note: To avoid saturating carpet,
rating carpet, as noted below.
do not use more than 4 wet
strokes over one area. Always end
with dry strokes.
It is best to alternate wet and dry
strokes as described above.
For best cleaning results and to aid
in faster drying of carpet, end with
more dry strokes. (Continue using
10
c. Empty tanks, rinse with clear water
and let air dry. Rinse the solution tank
cap and recovery tank lid and let air dry.
34
d. Remove debris from recovery
34
tank filter and rinse with clean
Note: If the filter is removed for clean-
water.
ing, it is easier to replace while it is still
e. If desired, vacuum thoroughly after
wet.
carpet has completely dried. This will
help reduce any shading left by the
cleaner's brushes.
dry strokes until little water is visible
passing through the recovery tank
lid.)
Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see
"Automatic shut-off", page 6).
When finished cleaning, follow "After
cleaning" instructions in section
above.
36
Clean Surge™
36
Button
The Clean Surge™ button can be
used to dispense extra solution
when cleaning particularly soiled
areas of carpet or spots.
To use, press Clean Surge™ button
while squeezing solution trigger. For
normal solution spray, release but-
ton and continue to squeeze solu-
tion trigger.
Carpet Cleaning
Read "Before you begin cleaning"
instructions on page 9.
1. Fill clean solution tank (upper
tank) with HOOVER Carpet/
Upholstery Detergent according to
instructions on pages 7 and 8.
35
2. Move speed selector to LO
for gentle cleaning or Hl for
normal cleaning.
35
properly grounded outlet.
3. Dry hands and plug cord into a
Do not clean over floor electrical
outlets.
4. To avoid walking on damp carpet,
start at the end of the room farthest
from the door or path to sink where
tanks will be emptied and filled.

Picking up spills

be used to pick up small liquid spills
Your Brush 'N' Wash cleaner may also
(3.78 l or less, never to exceed 6 mm
in depth) on carpet, upholstery, or bare
floors.
For best results, pick up spills immedi-
ately by placing the stair/upholstery noz-
zle just above the spill and suction up
any residue on top of the carpet. If the
upholstery nozzle or floor nozzle with
spill remains, place either the stair/
brushes turned OFF in front of the spill.
Pull the nozzle very slowly over the spill
initially with suction only. Repeat with spray
When picking up spills on bare floors,
and suction.
use only the floor nozzle with the bare
floor attachment (available at additional
cost if not included with your cleaner) in
place and speed selector in the OFF
position (this will help prevent spreading
the spill).
If a stain is left, the stair/upholstery nozzle is
generally more effective for removing it.
Although no cleaning solution can com-
pletely remove all stains, they can be treat-
ed by following the instructions provided by
the manufacturer of the carpet, upholstery,
Do not use the cleaner to pick up flam-
or bare floor surface being cleaned.
mable or combustible liquids or chemi-
cals.
When finished, follow "After cleaning"
instructions on page 10.