Table of Contents
Advertisement
Available languages
Available languages
Original operating instructions
1) Declaration of Conformity
We, being solely responsible, hereby declare that
these pipe grinding machines, identified by type and
serial number, meet all relevant requirements of
directives and standards.
2) Specified Conditions of Use
The pipe grinder is suited for
• burnishing, deadening and structuring
• polishing and smoothing,
• sanding and deburring the following materials:
• metal, wood and plastics.
It is for dry processing only.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
3) General Safety Information
Pay attention to all parts of the text that
are marked with this symbol for your own
protection and for the protection of your
power tool!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and instructions.
Failure to follow all safety warnings and instruc-
tions may result in an electric shock, fire and/or
serious injury verursachen.
Keep all safety instructions and information for
future reference. Pass on your power tool only together
with these documents.
4) Special Safety Instructions
4.1 General Safety Recommendations for grinding and
polishing:
a) This power tool is intended to function as a pipe
grinder or polisher. Read all safety warnings, instruc-
tions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
b) This power tool is not suitable for the use as angle
grinder (for example grinding or cutting-off). Opera-
tions for which the power tool was not designed may
create a hazard and cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer. Just because the accessory can
be attached to your power tool, it does not assure safe
operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
12
e) The dimensions of the belts must be within the
capacity rating of your power tool. Incorrectly sized belts
cannot be adequately guarded or controlled.
f) Do not use a damaged belts. Before each use inspect
the accessory for, tear or excess wear.
If a power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position your-
self and bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-load
speed for one minute. Damaged accessories will nor-
mally break apart during this test time.
g) Wear personal protective equipment.
Depending on application, use face shield, safety gog-
gles or safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron capable
of stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or
respirator must be capable of filtrating particles genera-
ted by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
h) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear per-
sonal protective equipment. Fragments of workpiece
or of a broken accessory may fly away and cause injury
beyond immediate area of operation.
i) Hold the power tool by the insulated gripping
surfaces only when performing an operation where the
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a „live" wire may make
exposed metal parts of the power tool „live"and shock
the operator.
j) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and
your hand or arm may be pulled into the spinning
accessory.
k) Never lay the power tool down until the
accessory has come to a complete stop. The spinning
accessory may grab the surface and pull the power tool
out of your control.
l) Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
m) Regularly clean the power tool's air vents. The mo-
tor's fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
n) Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
o) Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
4.2 Kickback and related warnings
Kickback is a sudden reaction to a pinched or
snagged grinding belts, polishing belts or any
EN
Advertisement
Table of Contents
