Advertisement
SICAM FCG Device
6MD2340
NOTE
To avoid a short circuit on the battery contacts, the
battery may only be removed with a non-conductive
tool (for example plastic tweezers).
3. Insert the battery into the battery compartment with the polarity
imprinted on the top side of the device.
4. Press the cover of the battery compartment back into the
housing and make sure it is in the correct position.
NOTE
Battery disposal
For disposing the batteries it is necessary to observe
the local national/international directives.
DIN-rail assembly
Mount the device on a DIN rail that is specified in the standard EN 60750.
1.
Pull down the release handle at the snap-on clip and hold it in
this position.
2.
Slide the device with the guiding of the snap-on clip onto one
side of the DIN rail and then to the desired position.
3.
Release the release device. The device is now firmly mounted
on the DIN rail.
NOTE
The snap-on clip is adjusted to a certain height
setting by the manufacturer. You can change this
position if necessary. To do so, lever the release
device out of its guiding (no special tool required)
and move the release device into the desired
position. Subsequently, press the release device
back into its guiding.
Communication Mobile
Danger
Risk of lightning strikes when installed outdoors
Non-observance leads to death or serious injury.
If you install an antenna outside, the antenna must be
grounded to protect it from lightning strikes. This work
must only be carried out by qualified personnel. Antennas
installed outdoors must be within the area covered by a
lightning protection system. Make sure that all conducting
systems entering from outdoors can be protected by a
lightning protection potential equalization system. When
implementing your lightning protection concept, make
sure you adhere to the VDE 0182 or IEC 62305 standard.
Commissioning
1. Check that the operational data match the rated data on the label and
the technical data of the device. This applies in particular to the supply
voltage and to the maximum values.
2. Connect the desired devices to the terminals and plug connectors (see
figure 1).
3. Install the SIM card and connect the GSM antenna according to Device
Manual.
4. Switch on the connected peripheral devices and the supply voltage of
the device.
NOTE
The device does not have a power on/off switch.
Switch on/off the supply voltage at the respective
isolating device or at the external power supply.
The cable length between SICAM FCG and the
external power supply must not exceed 0.5 m.
NOTE
Use copper conductors only.
NOTE
Field wires of control circuits shall be separated from
other circuits with respect to the end use
requirements.
Operation
Prerequisites
Most control functions require the input of passwords. This applies to all
entries affecting the device functions.
No password is required to read out data, indications, and diagnostic data.
NOTE
The device comes delivered with the following default
passwords:
- Activation password: 000000
- Maintenance password: 311299
Once commissioning has been completed, you should change the
passwords to protect the device against unintentional changes and
operation by unauthorized persons. How to change the passwords is
described in the device manual.
The devices are operated via the connected PC using web browser.
Operation is described in detail in the respective device manual. In the
following, the most important settings are described:
The graphical user interface is stored in the device. To display the user
interface, start Microsoft Internet Explorer 8.0 (or higher) and enter the IP
address (default IP address: 192.168.0.55; also see label on the side of
the device) of the device.
You can navigate through browser (for example Microsoft Internet
Explorer) using the icons on the toolbar, for example back, forward, print
etc. The user interface itself does not contain any navigation icons.
The following table lists the control elements:
Control Element
s
Control Function
Option button: selects one option
List box: selects an item from a list
Button: Executing an action by
clicking the button, that is the
current settings on the user
interface are transmitted to the
device.
Active tab (light blue)
Inactive tab (dark blue)
Selects and opens the item to be
activated, for example a tab
Product Information
E50417-X1040-C584-A3, Edition 09.2016
Advertisement
