Summary of Contents for Associated Electrics SC10GT
Page 2
Based on the ROAR National Winning RC10 GT2, the engineers behind the doors in Area 51 made the SC10GT both, all show and all go! The result is the SC10GT, an authentic scale experience at a level of performance that has never been seen before in 1:10 scale short course.
Page 3
Each part in the foldout This symbols indicates a has a number assigned to it for ordering special note or instruction replacement parts. in the manual. Associated Electrics, Inc. Customer Service 26021 Commercentre Dr. Tel: 949.544.7500 Lake Forest, CA 92630 Fax: 949.544.7501...
Page 5
:: Steering Build (cont.) - Bag A 6925 4-40 x 1/2” 9563 shcs Front bulkhead 7892 Front sub chassis kickup 6922 6922 6915 4-40 x 1/2” 4-40 x 5/8” fhcs fhcs :: Steering Build (cont.) - Bag A 3977 6272 3/16 x 3/8 Foam 6277...
Page 6
:: Steering Build (cont.) - Bag A 7260 4-40 3983 small Ballstud plain nut .30 black (long) 7922 Caster block 7927 6272 (30˚) Outer Foam hinge dust Build left and cover right sides! :: Steering Build (cont.) - Bag A 7917 Front arm (left &...
Page 7
:: Front Shock Tower/Bumper Build (cont.) - Bag A 6332 Body clips 6295 4-40 plain 3897 Pivoting 6924 body mount 4-40 x 3/8 shcs 7738 4-40 x 7/8 shcs 7103 6924 Front 4-40 x 3/8 body shcs 9820 post Front body mount :: Front Shock Tower/Bumper Build (cont.) - Bag A...
Page 8
2.80” steel Turnbuckle turnbuckle 53mm Orient the notch to the left throughout the car. It indicates which end has the left hand threads! :: Front Shock Tower/Bumper Build (cont.) - Bag A 7107 SC10GT chassis 6922 4-40 x 1/2 fhcs...
Page 9
:: Ball Differential Build - Bag B 7666 7666 Diff ring Diff ring 6581 3/32” carbide diff balls 7664 Diff gear 7667 7668 Diff outdrive Diff outdrive hub, right hub, left :: Ball Differential Build (cont.) - Bag B 6574 5/64 diff thrust...
Page 10
:: Gearbox Build - Bag B 7960 shaft 7963 Idler gear cluster 44-28T 7961 3977 top shaft 3/16 x 3/8 spacer ball bearing :: Gearbox Build (cont.) - Bag B 7945 7945 Transmission Transmission case case (left side) (right side) 3977 3/16 x 3/8 ball bearing...
Page 11
:: Gearbox Build (cont.) - Bag B 7947 Brake 7949 top hat Brake bushing 7950 Brake disc :: Gearbox Build (cont.) - Bag B 7633 4-40 x 5/8 bhcs 7953 Slipper plate, inner 7948 Brake Align the flat spots on the inner slipper plate to the brake disc and top shaft.
Page 12
:: Rear Shock Tower Build - Bag B 3897 6332 7413 Pivoting Body 4-40 x 3/4 body mount clips bhcs 6917 4-40 x 3/8 bhcs 7260 Plain nut 7103 Rear body mounts 7102 Rear shock tower (SC10 GT) :: Rear Shock Tower Build (cont.) - Bag B 7217 Rear Camber 6926...
Page 13
:: Rear Shock Tower Build (cont.) - Bag B 6925 4-40 x 1/2 shcs 6915 4-40 x 5/8 fhcs :: Rear Suspension Build - Bag C 9621 7930 Rear inner 7928 Rear arms hinge pins (1 left & mount 1 right) (3+2) :: Rear Suspension Build (cont.) - Bag C 7260...
Page 14
:: Rear Suspension Build (cont.) - Bag C 6925 4-40 x 1/2 shcs 7904 Battery Note: Wire opening in receiver box top pack lid and wire hooks in transmission case. Racer Tip: Add foam padding (not inluded) to cushion receiver 6925 pack.
Page 15
:: Rear Suspension Build (cont.) - Bag C 7932 1.5 degree rear hubs 7462 (1 left & Dogbone 9645 1 right) 2-56 x 1/8 7935 bhcs .187x.50x.196 5407 bearing o-ring 9670 7927 3/16 Outer rear hinge pin 3977 axle 3/16 x 3/8 5407 9273 bearing...
Page 16
7337 .250 x .125 x .015 .250 x .125 x .015 Washer Washer Throttle servo 7106 Radio tray (SC10GT) :: Radio Tray Build (cont.) - Bag D Receiver 7896 Radio box, lower 9146 2-56 x 3/16 bhcs :: Radio Tray Build (cont.) - Bag D...
Page 17
.250 x .125 x .015 Washer 7108 Muffler wire (SC10GT) :: Radio Tray Build (cont.) - Bag D You have the option of using the larger 1/8 scale fuel tank (#89324 not included) for longer run times. This will require the use of red o-rings (#5407) to mount the large tank (see page 30 for details).
Page 18
:: Radio Tray Build (cont.) - Bag D 6925 4-40 x 1/2 shcs :: Radio Tray Build (cont.) - Bag D 6922 4-40 x 1/2 fhcs...
Page 19
:: Radio Tray Build (cont.) - Bag D 6925 4-40 x 1/2 shcs 7911 Steering Ball servo link 7891 Chassis brace 7911 Servo link rod 11.5mm :: Throttle and Brake Linkage Build - Bag E Large 7975 4449 Throttle 4-40 x 3/16 pivot locknut large...
Page 20
:: Throttle and Brake Linkage Build (cont.) - Bag E 8427 .018 spring 7975 25225 Brake M3x3 adjustment setscrew knob 7975 Throttle pivot 7975 collar 7975 small Brake hole linkage wire :: Throttle and Brake Linkage Build (cont.) - Bag E 7562 Throttle return...
Page 21
:: Engine Build - Bag F Nitro Engine 7975 2-56 7618 plain Flywheel shim 7975 7618 2-56 Collet ballstud :: Engine Build (cont.) - Bag F 7993 Flywheel 2-shoe 2313 clutch :: Engine Build (cont.) - Bag F Assembled example 7971 0.9mm Clutch...
Page 22
:: Engine Build (cont.) - Bag F The amount of shims may vary depending on engine type. Min. shims - 2 Max shims - 4 2321 Shim until clutch spins freely with minimal play. Clutch shim 2321 7968 4.8mm clutch clutch shim bell...
Page 23
:: Engine Build (cont.) - Bag F Attach the air filter to the carburetor with a nylon wire tie. 7705 filter 3719 6” Nylon Oil the foam pre- filter element using wire ties #7710 Prefilter Treatment. :: Engine Build (cont.) - Bag F NOTE: Make sure to set gear mesh (see page 24) before tightening engine...
Page 24
Adjust EPA so that carburetor is completely open at full throttle. Set max brake EPA. It is easiest to do this while driving the SC10GT. Start at 50% and adjust accordingly. Lower % = less brake. Higher % = more brake.
Page 25
:: Shocks Build - Bag G 6469 6469 Shock Shock Remove 9884 9885 spurs o-ring o-ring V2 RTR V2 RTR front shock front shock body 1.02” body 1.39” stroke stroke (blue) (blue) Piston 7484 Shock 7484 5407 5407 internal Shock spacer internal o-ring...
Page 26
:: Shocks Build (cont.) - Bag G 6441 * Shock Bleeding Steps: Shock 1. Pull shock shaft down. 2. Fill shock body 3/4 full with silicone fluid. 3. Slowly move the shock shaft up and (molded) down to remove air from under piston. 4.
Page 27
:: Shocks Build (cont.) - Bag G 6473 Shock bushings 6472 Shock mounting 6925 Rear Build left and 4-40 x 1/2 right sides! Shock shcs :: Wheel and Tire Assembly 91101 91101 KMC Hex KMC Hex Wheel Wheel 89413 89413 (black) (black) 91101...
Page 28
:: Wheel and Tire Assembly (cont.) 6952 8-32 steel locknut 6953 8-32 low profile steel locknut :: Body Install 6332 Body clip...
Page 29
Recommended Gearing: SC10GT gear chart To calculate your SC10GT Final Drive Ration (a.k.a. gear ratio), use the following formula: Spur Gear (spur gear # teeth) / (clutch bell # teeth) x 4.09 = Final Drive Ratio 11.62...
Page 30
6918 6918 89324 89324 The SC10GT has a unique radio tray that allows you to install a larger fuel tank (# 89324) for longer run times. Simply removing 6918 6918 the radio tray insert, and install the optional fuel tank (not included)
Page 32
:: Steering 2234 Swing Rack Bushing 2234 3981 Ballstud .20” Black, short 7908 6272 Foam Ballend Dust Covers 6276 Ballstud .20” Silver, short 6272 6629 6277 Ballstud .30” Silver, short 6272 7908 6629 5-40 Locknuts 7908 6917 4-40 x 3/8 BHCS 6276 6922 4-40 x 1/2 FHCS...
Page 33
:: Front Bulkhead 4334 2-56 x 5/16 BHCS 6915 4-40 x 5/8 FHCS 6925 6922 4-40 x 1/2 FHCS 6925 4-40 x 1/2 SHCS 6925 7892 Front Sub Chassis 7893 Top Plate 9563 Front Bulkhead 6925 9564 Front Chassis Brace 7893 9564 9563...
Page 34
4-40 x 3/4 FHCS 7562 6924 4-40 x 3/8 SHCS 21173 6924 6925 4-40 x 1/2 SHCS 6924 7106 SC10GT Radio Tray 7107 SC10GT Chassis 7896 7108 SC10GT Muffler Wire 7337 7337 .250 x .125 x .015 Washer 7562 Throttle Return Spring 7724 Fuel Line 15”...
Page 39
:: Factory Team and Option Parts :: AE Nitro Engines and Accessories MC59 McCoy Glow Plug 1408 FT Titanium Turnbuckles, 2.65” 1738 FT Glow Starter 1417 FT Titanium Turnbuckles, 2.8” 1748 Nitro Fuel Bottle, 600cc 1419 FT Titanium Turnbuckles, 3.0” 1420 FT Titanium Turnbuckle Set 1749...
Page 40
:: XP Electronics :: RePlay Cameras 29107 S1903 Metal Gear Set RP001 Replay XD1080 Complete Camera System 29125 S1903MG Servo RP002 Replay XD720 Complete Camera System 29126 S2008MG Servo RP021 Replay XD1080 Lens Bezel Kit 29127 S2008MG Gear Set RP022 Replay XD1080 Clear Lens Cover 29150 XP2/XP3 RX/TX Charger, 110V...
Page 41
(ready-to-run) 91107 13mm Shock Tools 20504 Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run) Associated Electrics, Inc. 80904 FT RC8Be Electric Buggy Kit 26021 Commercentre Drive 80905 RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run) Lake Forest, CA 92630-8853 USA 80906 RC8.2 FT Nitro Buggy Kit...
Page 43
Driver: SC10GT RTR Setup Date: Track: Event: Conditions: Rev.1 Setup Sheet Front Suspension Rear Suspension Washers: Washers: 0.30” long Ballstud: Washers: Wheelbase: Long Long Medium Medium Short Short -1 degree Camber: 2 degree Anti-Squat: -1 degree Camber: 31mm Ride Height: 0 degree 1.5 degree...
Page 44
:: Hardware - 1:1 Scale View Socket Head (shcs) Flat Head (fhcs) Button Head (bhcs) 4-40 x 3/8 (6924) 4-40 x 3/8 (6292) 2-56 x 1/8 (9645) 4-40 x 1/2 (6925) 4-40 x 1/2 (6922) 2-56 x 3/16 (9146) 4-40 x 5/8 (6926) 4-40 x 5/8 (6915) 2-56 x 5/16 (4334) 4-40 x 3/4 (6927)
Page 45
Driver: Date: Track: Event: Conditions: Rev.1 Setup Sheet Front Suspension Rear Suspension Washers: Washers: Ballstud: Washers: Wheelbase: Long Long Medium Medium Short Short Camber: Anti-Squat: Camber: Ride Height: Toe: Hub Toe: Ride Height: Caster: 20˚ 25˚ 30˚ Front Shocks Rear Shocks Spring: Piston: Spring:...
Need help?
Do you have a question about the SC10GT and is the answer not in the manual?
Questions and answers