Table of Contents
Advertisement
Quick Links
Instructions
Stainless Steel Pump Lower
For use with EcoQuip 2
with additives to inhibit corrosion or mold. For professional use only.
Model 24V671
1100 psi (7.5 MPa, 75 bar) Maximum Fluid Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual and in your EcoQuip 2 system
manual before using the equipment. Save
all instructions.
™
vapor abrasive blast equipment. Only use with water or water
3A6845A
EN
Advertisement
Table of Contents
Related Manuals for Graco 24V671
Summary of Contents for Graco 24V671
- Page 1 For use with EcoQuip 2 vapor abrasive blast equipment. Only use with water or water with additives to inhibit corrosion or mold. For professional use only. Model 24V671 1100 psi (7.5 MPa, 75 bar) Maximum Fluid Working Pressure Important Safety Instructions...
-
Page 2: Table Of Contents
Fill the Wet Cup ......6 Graco Standard Warranty ....14 Operation. -
Page 3: Warnings
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable. - Page 4 Warnings WARNING MOVING PARTS HAZARD Moving parts can pinch, cut or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources.
-
Page 5: Component Identification
Component Identification Component Identification . 1: Component Identification Key: Enclosed Wet Cup Lower Cylinder Wet Cup Fill Port Outlet Housing Fluid Outlet Displacement Rod Fluid Inlet Sight Glass 3A6845A... -
Page 6: Setup
Tighten Threaded Connections Before each use, check all hoses for wear or damage. Replace as necessary. Check that all threaded connections are tight and leak-free. Wet Cup Fill the wet cup half-full of Graco TSL. Verify the level of TSL daily. 3A6845A... -
Page 7: Repair
Repair Repair 14. Verify that the insides of the piston seat (114) and intake seat (113) are not chipped or nicked. 15. Clean all parts and threads with a compatible solvent. Disassemble the Pump Lower Reassemble the Pump Lower 1. Follow the Pressure Relief Procedure, page 6. 1. - Page 8 Repair 9. If the piston ball stop pin (110) was removed, slide 13. If the piston (128) was removed from the the piston ball stop pin (110) into the shorter set of displacement rod (107), reassemble them back holes (L) in the piston (128). together.
- Page 9 Repair Detail A: Throat Packings Detail B: Piston Packings . 4: Pump Assembly See Detail B. Lubricate. Position the lips of the v-packings face-up. See Detail A. Apply lubricant. Position the lips of the v-packings facedown. Torque to 60 ft-lb (81 N•m). 3A6845A...
-
Page 10: Parts
Parts Parts Pump Lower 3A6845A... - Page 11 Parts Ref. Part Description Qty. Ref. Part Description Qty. 136✠ 102228 COVER, oil hole 101† 100063 PIN, cotter 137✠ --- SIGHTGLASS, plastic 102† 101917 BALL, bearing, 0.875 dia. 304 ss 138✠ --- PLUG, pipe, sst, 1/8 npt 104† 164782 PACKING, o-ring, 2 1/16 x 2 1/4 139✠...
-
Page 12: Dimensions
Dimensions Dimensions Ref. Dimensions 4.75 in. (120 mm) 3.95 in. (100 mm) 16.0 in. (405 mm) 3A6845A... -
Page 13: Technical Specifications
Technical Specifications Technical Specifications Stainless Steel Pump Lower (24V671) Metric Maximum fluid working pressure 1100 psi 7.5 MPa, 75 bar Maximum ambient temperature 110°F 43°C Minimum fluid temperature 110°F 43°C Lower size 120 cc Stroke length 2.5 in. 64 mm... -
Page 14: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.