HIKVISION iDS-7200AHQHI-M Series User Manual

HIKVISION iDS-7200AHQHI-M Series User Manual

Atm
Table of Contents

Advertisement

Quick Links

ATM Digital Video Recorder
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iDS-7200AHQHI-M Series and is the answer not in the manual?

Questions and answers

Summary of Contents for HIKVISION iDS-7200AHQHI-M Series

  • Page 1 ATM Digital Video Recorder User Manual...
  • Page 2 ATM Digital Video Recorder User Manual Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
  • Page 3 ATM Digital Video Recorder User Manual TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
  • Page 4 ATM Digital Video Recorder User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
  • Page 5 ATM Digital Video Recorder User Manual Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
  • Page 6 ATM Digital Video Recorder User Manual Applicable Model This manual is applicable to the following model. Series Model iDS-7200AHQHI-M iDS-7204AHQHI-M1...
  • Page 7 ATM Digital Video Recorder User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could Caution result in equipment damage, data loss, performance degradation, or...
  • Page 8 ATM Digital Video Recorder User Manual Safety Instruction • Proper configuration of all passwords and other security settings is the responsibility of the installer and/or user. • In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
  • Page 9 ATM Digital Video Recorder User Manual Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • Ensure recorder is installed in a well-ventilated, dust-free environment. • Recorder is designed for indoor use only. •...
  • Page 10: Table Of Contents

    ATM Digital Video Recorder User Manual Contents Chapter 1 Basic Operation ......................1 1.1 Activate Your Device ......................1 1.1.1 Default User and IP Address ..................1 1.1.2 Activate via Local Menu ....................1 1.1.3 Activate via SADP ......................2 1.1.4 Activate via Client Software ..................
  • Page 11 ATM Digital Video Recorder User Manual 2.3.7 Call a Pattern ....................... 18 2.3.8 Set Linear Scan Limit ....................18 2.3.9 One-Touch Park ......................19 Chapter 3 Recording and Playback .................... 20 3.1 Recording ..........................20 3.1.1 Configure Recording Parameters ................20 3.1.2 Enable the H.265 Stream Access .................
  • Page 12 ATM Digital Video Recorder User Manual 4.2.1 Panel Mode ......................... 32 4.2.2 Human Face Mode ...................... 34 4.3 VCA Event Alarm ........................36 4.3.1 Facial Detection ......................36 4.3.2 Vehicle Detection ......................37 4.3.3 Line Crossing Detection ....................38 4.3.4 Intrusion Detection ..................... 40 4.3.5 Region Entrance Detection ..................
  • Page 13 ATM Digital Video Recorder User Manual 6.1 Manage Local HDD ....................... 55 6.1.1 Configure HDD Group ....................55 6.1.2 Configure the HDD Property ..................56 6.1.3 Configure the HDD Quota ................... 57 6.2 Add a Network Disk ......................57 Chapter 7 Network Settings ...................... 59 7.1 Configure TCP/IP Settings .....................
  • Page 14 ATM Digital Video Recorder User Manual 10.1 Manage User Accounts ...................... 74 10.1.1 Add a User ......................... 74 10.1.2 Edit the Admin User ....................75 10.1.3 Edit an Operator/Guest User ..................76 10.2 Manage User Permissions ....................76 10.2.1 Set User Permissions ....................76 10.2.2 Set Live View Permission on Lock Screen ..............
  • Page 15 ATM Digital Video Recorder User Manual 11.4.2 Repair Database ......................90 11.5 Upgrade System ......................... 90 11.5.1 Upgrade Device ......................90 11.5.2 Upgrade Analog Cameras ..................92 11.5.3 Upgrade IP Cameras ....................92 11.6 Import/Export Device Configuration Files ................93 11.7 Search &...
  • Page 16: Chapter 1 Basic Operation

    ATM Digital Video Recorder User Manual Chapter 1 Basic Operation 1.1 Activate Your Device 1.1.1 Default User and IP Address • Default administrator account: admin. • Default IPv4 address: 192.168.1.64. 1.1.2 Activate via Local Menu For the first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation.
  • Page 17: Activate Via Sadp

    ATM Digital Video Recorder User Manual And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 2. Enter the password to activate the IP cameras. 3.
  • Page 18: Activate Via Client Software

    ATM Digital Video Recorder User Manual Figure 1-2 Activate via SADP 4. Create and input the new password in the password field, and confirm the password. Note We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 19 ATM Digital Video Recorder User Manual Figure 1-3 Control Panel 2. Click Device Management to enter the Device Management interface, as shown below. Figure 1-4 Device Management Interface 3. Check the recorder status from the device list, and select an inactive recorder. 4.
  • Page 20 ATM Digital Video Recorder User Manual Note We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
  • Page 21: Activate Via Web Browser

    ATM Digital Video Recorder User Manual 1.1.5 Activate via Web Browser You can get access to the recorder via web browser. You may use one of the following listed web browsers: Internet Explorer 6.0 and above, Apple Safari, Mozilla Firefox, and Google Chrome. The supported resolutions include 1024*768 and above.
  • Page 22: Add Network Camera

    ATM Digital Video Recorder User Manual Figure 1-8 TCP/IP Settings 2. Configure network parameters as needed. Note • Check Enable DHCP to obtain IP settings automatically if a DHCP server is available on the network. • Valid MTU value range is 500 to 9676. 3.
  • Page 23: Add Automatically Searched Online Network Camera

    ATM Digital Video Recorder User Manual Figure 1-9 Signal Input Type 2. Select signal input type as HD/CVBS or IP for each channel. HD/CVBS Four types of analog signal inputs including Turbo HD, AHD, HDCVI, and CVBS can be connected randomly for the channel. Network camera can be connected for the channel.
  • Page 24 SDK service, the default port value is 8000. For enhanced SDK service, the default value is 8443. Note The function is only available when you use HIKVISION protocol. 6. Optional: Check Verify Certificate to verify the camera with certificate. The certificate is a form of identification for the camera that provides more secure camera authentication.
  • Page 25: Platform Access

    ATM Digital Video Recorder User Manual 1.4 Platform Access 1.4.1 Configure Guarding Vision Guarding Vision enables the mobile phone application and the service platform page (dev.guardingvision.com) to access and manage your connected NVR, providing a convenient remote access to the surveillance system. Steps 1.
  • Page 26: Chapter 2 Live View

    ATM Digital Video Recorder User Manual Chapter 2 Live View Live view displays the video image getting from each camera in real time. 2.1 Start Live View Click on the main menu bar to enter the Live View. • Select a window and double click a camera from the list to play the video from the camera in the selected window.
  • Page 27: Configure Live View Mode

    ATM Digital Video Recorder User Manual Volume Adjust the Live View volume, playback and two-way audio for the selected output interface. Event Output Select the output to show event video. Full Screen Monitoring Dwell Time Set the time in seconds to show alarm event screen. 3.
  • Page 28: Ptz Control

    ATM Digital Video Recorder User Manual Figure 2-2 Digital Zoom 2.3 PTZ Control 2.3.1 Configure PTZ Parameters Follow these procedures to set the PTZ parameters. The PTZ parameters configuration must be done before you can control the PTZ camera. Steps 1.
  • Page 29: Set A Preset

    ATM Digital Video Recorder User Manual 3. Edit the PTZ parameters. Note All the parameters should be exactly match the PTZ camera parameters. 4. Click OK to save the settings. 2.3.2 Set a Preset Presets record the PTZ position and the status of zoom, focus, iris, etc.You can call a preset to quickly move the camera to the predefined position.
  • Page 30: Set A Patrol

    ATM Digital Video Recorder User Manual Figure 2-6 Call Preset (1) Figure 2-7 Call Preset (2) 2.3.4 Set a Patrol Patrols can be set to move the PTZ to key points and have it stay there for a set duration before moving on to the next key point.
  • Page 31 ATM Digital Video Recorder User Manual Figure 2-9 Patrol Settings 5. Click to add a key point to the patrol. Figure 2-10 Key Point Configuration 1) Configure key point parameters. Preset Determines the order the PTZ will follow while cycling through the patrol. Speed Defines the speed the PTZ will move from one key point to the next.
  • Page 32: Call A Patrol

    ATM Digital Video Recorder User Manual Operation Description Operation Description Select a key Edit the added point to delete. key point. Adjust the key Adjust the key point order point order 7. Click Apply to save the patrol settings. 2.3.5 Call a Patrol Calling a patrol makes the PTZ move according to the predefined patrol path.
  • Page 33: Call A Pattern

    ATM Digital Video Recorder User Manual Figure 2-12 Pattern Configuration 3. Select the pattern No. 4. Set the pattern. 1) Click Record to start recording. 2) Click corresponding buttons on the control panel to move the PTZ camera. 3) Click Stop to stop recording. The PTZ movement is recorded as the pattern. 2.3.7 Call a Pattern Follow the procedure to move the PTZ camera according to the predefined patterns.
  • Page 34: One-Touch Park

    (park time). Before You Start Before operating this function, make sure the connected camera supports linear scan and is in HIKVISION protocol. Steps 1. Click on the quick settings toolbar of the PTZ camera's live view.
  • Page 35: Chapter 3 Recording And Playback

    ATM Digital Video Recorder User Manual Chapter 3 Recording and Playback 3.1 Recording 3.1.1 Configure Recording Parameters Go to Camera → Video Parameters . Main Stream Main stream refers to the primary stream that affects data recorded to the hard disk drive and will directly determine your recording quality and image size.
  • Page 36: Enable The H.265 Stream Access

    ATM Digital Video Recorder User Manual Sub-Stream Sub-stream is a second codec that runs alongside the main stream. It allows you to reduce the outgoing internet bandwidth without sacrificing your direct recording quality. Sub-stream is often exclusively used by apps to view live video. Users with limited internet speeds may benefit most from this setting.
  • Page 37 ATM Digital Video Recorder User Manual Steps 1. Go to Storage → Schedule → Record . 2. Select a camera. 3. Check Enable Schedule. 4. Select a recording type. Continuous Scheduled recording. Event Recording triggered by all event triggered alarm. Motion Recording triggered by motion detection.
  • Page 38: Configure Holiday Recording

    ATM Digital Video Recorder User Manual Figure 3-1 Record Schedule Note • You can repeat the above steps to set schedule recording or capture for each day in the week. • Continuous recording is applied to each day by default. 6.
  • Page 39: Configure 1080P Lite Mode

    ATM Digital Video Recorder User Manual Figure 3-2 Edit Holiday Settings 5. Set Holiday Name, Mode, Start Date, and End Date. 6. Click OK. 7. Set the schedule for holiday recording. Refer to Configure Plan Recording for details. 3.1.6 Configure 1080p Lite Mode When 1080P Lite Mode is enabled, the encoding resolution at 1080P Lite (real-time) is supported.
  • Page 40: Play Normal Video

    ATM Digital Video Recorder User Manual Figure 3-3 Playback Interface 3.2.2 Play Normal Video Go to Playback, select date and camera(s), and use the toolbar at the bottom to perform playback operations. Refer to Playback Operations . You can click camera(s) to execute simultaneous playback of multiple camera(s).
  • Page 41: Play Custom Searched Files

    ATM Digital Video Recorder User Manual 3.2.3 Play Custom Searched Files You can play video by customized search conditions. Steps 1. Go to Playback. 2. Select camera(s) from the list. 3. Click Custom Search on the left bottom. 4. Enter search conditions, including Time, File Status, Event Type, etc. Figure 3-5 Custom Search 5.
  • Page 42 ATM Digital Video Recorder User Manual Add Tag Files Steps 1. Go to Playback. 2. Search and play back the video file(s). 3. Click to add the tag. 4. Edit the tag information. 5. Click OK. Note Max. 64 tags can be added to a single video file. Play Tag Files Steps 1.
  • Page 43: Play By Sub-Periods

    ATM Digital Video Recorder User Manual Figure 3-8 Searched Tag Files 5. Select a tag file, and play the video on the search results interface. 3.2.5 Play by Sub-periods The video files can be played in multiple sub-periods simultaneously on the screen. Steps 1.
  • Page 44: Playback Operations

    ATM Digital Video Recorder User Manual 3.3 Playback Operations 3.3.1 Edit Video Clips You can cut and export video clips during playback. Steps 1. Go to Playback 2. Click at the bottom toolbar. 3. Set the start time and end time. You can click to set the time period, or set a time segment on time bar.
  • Page 45: Chapter 4 Event

    ATM Digital Video Recorder User Manual Chapter 4 Event 4.1 Normal Event Alarm 4.1.1 Configure Motion Detection Alarms Motion detection enables the device to detect the moving objects in the monitored area and trigger alarms. Steps 1. Go to System → Event → Normal Event → Motion Detection . 2.
  • Page 46: Configure Sensor Alarms

    ATM Digital Video Recorder User Manual 2. Select a camera. 3. Check Enable. 4. Set the video tampering area. Drag on the preview screen to draw the customized video tampering area. 5. Set Sensitivity (0-2). 3 levels are available. The sensitivity calibrates how readily movement triggers the alarm.
  • Page 47: Smart Atm Event Alarm

    ATM Digital Video Recorder User Manual Figure 4-1 Event Hint Settings 3. Select an exception type. Figure 4-2 Exceptions Handling 4. Set the linkage actions. Refer to Configure Linkage Actions . 4.2 Smart ATM Event Alarm Two smart ATM modes are supported: panel mode, and human face mode. You can only enable one mode for the same analog camera.
  • Page 48 ATM Digital Video Recorder User Manual Figure 4-3 Panel Mode 2. Check Enable. 3. Select an analog camera. 4. Select Panel Mode. 5. Set Scene Description. Mounting Location The camera mounting location. Mounting Type The camera mounting type. Standing Region Contained in Scene Whether the scene contains the human standing region.
  • Page 49: Human Face Mode

    ATM Digital Video Recorder User Manual It will alarm if the selected rule type continues for the configured duration. For Operation Timeout, it ranges from 4 to 6000 seconds. For Sticking Scrip and Installing Scanner, it ranges from 4 to 60 seconds. Alarm Duration Alarm duration after the selected type is triggered.
  • Page 50 ATM Digital Video Recorder User Manual Figure 4-4 Human Face Mode 2. Check Enable. 3. Select an analog camera. 4. Select Human Face Mode. 5. Set Smart ATM Capture parameters for captured image. 6. Set Rule Configuration. 1) Check Enable of the selected rule. 2) Double click the rule, or click 3) Set Name, Type, Alarm Duration.
  • Page 51: Vca Event Alarm

    ATM Digital Video Recorder User Manual 1) Select a shield region in Select Shield Region. 2) Click Draw Shield Region. 3) Click on the live view image to draw points of the region. You can click Clear Prev. Point to clear the point that was previously drawn.
  • Page 52: Vehicle Detection

    ATM Digital Video Recorder User Manual Figure 4-5 Facial Detection 3. Select a camera to configure. 4. Check Enable Face Detection. 5. Optional: Check Save VCA Picture to save the captured pictures of face detection. 6. Set the detection sensitivity. Sensitivity range: [1-5]. The higher the value is, the more easily the face will be detected.
  • Page 53: Line Crossing Detection

    ATM Digital Video Recorder User Manual Figure 4-6 Vehicle Detection 4. Check Enable Vehicle Detection. 5. Optional: Check Save VCA Picture to save the captured vehicle detection pictures. 6. Set the arming schedule.Refer to Configure Arming Schedule 7. Set the linkage actions. Refer to Configure Linkage Actions 8.
  • Page 54 ATM Digital Video Recorder User Manual Figure 4-7 Line Crossing Detection 3. Select a camera. 4. Check Enable Line Crossing Detection. 5. Optional: Check Save VCA Picture to save the captured pictures of line crossing detection. 6. Set the line crossing detection rules and detection areas. 1) Select an arming area.
  • Page 55: Intrusion Detection

    ATM Digital Video Recorder User Manual 4.3.4 Intrusion Detection The Intrusion detection function detects people, vehicles or other objects that enter and loiter in a pre-defined virtual region. Specific actions can be taken when an alarm is triggered. Steps 1. Go to System → Event → Smart Event . 2.
  • Page 56: Region Entrance Detection

    ATM Digital Video Recorder User Manual 7. Set the arming schedule. Refer to Configure Arming Schedule . 8. Set linkage actions. Refer to Configure Linkage Actions . 9. Click Apply. 4.3.5 Region Entrance Detection Region entrance detection detects objects that enter a predefined virtual region. Steps 1.
  • Page 57: Region Exiting Detection

    ATM Digital Video Recorder User Manual 4.3.6 Region Exiting Detection Region exiting detection detects objects that exit from a predefined virtual region. Steps 1. Go to System → Event → Smart Event . 2. Click Region Exiting. Figure 4-10 Region Exiting Detection 3.
  • Page 58: Object Removal Detection

    ATM Digital Video Recorder User Manual Figure 4-11 Defocus Detection 3. Select a camera to configure. 4. Check Enable. 5. Optional: Check Save VCA Picture to save the captured defocus detection pictures. 6. Drag the Sensitivity slider to set the detection sensitivity. Note Sensitivity range: [1-100].
  • Page 59: Audio Exception Detection

    ATM Digital Video Recorder User Manual Figure 4-12 Object Removal Detection 3. Select a camera to configure. 4. Check Enable Object Removable Detection. 5. Optional: Check Save VCA Picture to save the captured object removable detection pictures. 6. Follow these steps to set the detection rules and detection areas. 1) Select Arming Region.
  • Page 60 ATM Digital Video Recorder User Manual Figure 4-13 Audio Exception Detection 3. Select a camera to configure. 4. Optional: Check Save VCA Picture to save the captured audio exception detection pictures. 5. Set the detection rules: 1) Select Exception Detection. 2) Check Audio Loss Exception,Sudden Increase of Sound Intensity Detection,and/or Sudden Decrease of Sound Intensity Detection.
  • Page 61: Sudden Scene Change Detection

    ATM Digital Video Recorder User Manual 4.3.10 Sudden Scene Change Detection Scene change detection detects the change of the surveillance environment affected by external factors, such as the intentional rotation of the camera. Steps 1. Go to System → Event → Smart Event . 2.
  • Page 62: Unattended Baggage Detection

    ATM Digital Video Recorder User Manual 4.3.11 Unattended Baggage Detection Unattended baggage detection detects the objects left over in a predefined region such as the baggage, purses, dangerous materials, etc., and a series of actions can be taken when the alarm is triggered.
  • Page 63: Pir Alarm

    ATM Digital Video Recorder User Manual 4.3.12 PIR Alarm A PIR (Passive Infrared) alarm is triggered when an intruder moves within the detector vision field. The heat energy dissipated by a person or any other warm blooded creature such as dogs, cats, etc., can be detected.
  • Page 64: Configure Arming Schedule

    ATM Digital Video Recorder User Manual 2. Select different detection types: smart detection ( ), vehicle detection ( ), face detection ), and human body detection ( 3. Select the historical analysis ( ) or real-time analysis ( ) to obtain the results. Note The smart analysis results of the detection are displayed in the list.
  • Page 65: Configure Linkage Actions

    ATM Digital Video Recorder User Manual 4.5 Configure Linkage Actions Alarm linkage actions will be activated when an alarm or exception occurs, including Event Hint Display, Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Trigger Alarm Output, and Send Email. 4.5.1 Configure Auto-Switch Full Screen Monitoring When an alarm is triggered, the local monitor displays in full screen the video image from the alarming channel configured for full screen monitoring.
  • Page 66: Notify Surveillance Center

    ATM Digital Video Recorder User Manual 4.5.3 Notify Surveillance Center The device can send an exception or alarm signal to the remote alarm host when an event occurs. The alarm host refers to the PC installed with client software (e.g., iVMS-4200, iVMS-5200). Steps 1.
  • Page 67: Chapter 5 Camera Settings

    ATM Digital Video Recorder User Manual Chapter 5 Camera Settings 5.1 Configure Image Parameters You can customize image parameters, including day/night switch, backlight, contrast, and saturation in Camera → Display . Image Settings Customize the image parameters including brightness, contrast, and saturation. Exposure Set the camera exposure time (1/10000 to 1 sec).
  • Page 68: Configure Privacy Mask

    ATM Digital Video Recorder User Manual Figure 5-1 OSD Configuration Interface 6. Drag the text frame on the preview window to adjust the OSD position. 7. Click Apply. 5.3 Configure Privacy Mask The privacy mask protects personal privacy by concealing parts of the image from kive view or recording with a masked area.
  • Page 69 ATM Digital Video Recorder User Manual Figure 5-2 Privacy Mask Settings Interface Note • Up to 4 privacy masks zones can be configured and the size of each area can be adjusted. • You can clear the configured privacy mask zones on the window by clicking the corresponding clear zone 1 to 4 icons on the right of the window, or click Clear All to clear all zones.
  • Page 70: Chapter 6 Storage

    ATM Digital Video Recorder User Manual Chapter 6 Storage 6.1 Manage Local HDD 6.1.1 Configure HDD Group Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD group through HDD settings. Steps 1.
  • Page 71: Configure The Hdd Property

    ATM Digital Video Recorder User Manual Figure 6-2 Local HDD Settings 7. Select a group number for the HDD. 8. Click OK. Note Regroup the cameras for HDD if the HDD group number is changed. 9. Go to Storage → Storage Mode . 10.
  • Page 72: Configure The Hdd Quota

    ATM Digital Video Recorder User Manual HDD supports both read and write. Read-only Files in read-only HDD will not be overwritten. Redundant Save the videos and pictures not only in the R/W HDD but also in the redundant HDD. It effectively enhances the data safety and reliability.
  • Page 73 ATM Digital Video Recorder User Manual Figure 6-3 Add NetHDD 3. Select NetHDD type. 4. Enter NetHDD IP address and click Search to search the available NetHDD. 5. Select the desired NetHDD. 6. Click OK. 7. The added NetHDD will be displayed in the HDD list. Select the newly added NetHDD and click Init.
  • Page 74: Chapter 7 Network Settings

    ATM Digital Video Recorder User Manual Chapter 7 Network Settings 7.1 Configure TCP/IP Settings TCP/IP settings must be properly configured before you can operate the device over a network. Steps 1. Go to System → Network → TCP/IP . Figure 7-1 TCP/IP Settings 2.
  • Page 75: Configure Pppoe

    ATM Digital Video Recorder User Manual Before You Start You must register the DynDNS, PeanutHull, or NO-IP services with your ISP before configuring DDNS settings. Steps 1. Go to System → Network → TCP/IP → DDNS Figure 7-2 DDNS Settings 2.
  • Page 76: Configure Port

    ATM Digital Video Recorder User Manual Figure 7-3 NTP Settings 2. Check Enable. 3. Configure NTP settings as need. Interval (min) Time interval between two time synchronization with NTP server. NTP Server IP address of the NTP server. NTP Port Port of the NTP server.
  • Page 77 ATM Digital Video Recorder User Manual Figure 7-4 Port Settings 2. configure port settings as needed. Alarm Host IP/Port With a remote alarm host configured, the device will send the alarm event or exception message to the host when an alarm is triggered. The remote alarm host must have the client management system (CMS) software installed.The alarm host IP refers to the IP address of the remote PC on which the CMS software (e.g., iVMS-4200) is installed, and the alarm host port (7200 by default) must be the same as the alarm monitoring port configured in the...
  • Page 78: Configure Port Mapping (Nat)

    ATM Digital Video Recorder User Manual RTSP (Real Time Streaming Protocol) is a network control protocol designed to control streaming media servers. The port is 554 by default. Enhanced SDK Service Port The enhanced SDK service adopts TLS protocol over the SDK service that provides safer data transmission.
  • Page 79: Configure Onvif

    ATM Digital Video Recorder User Manual Note • You can use the default port No., or change it according to actual requirements. • External Port indicates the port No. for port mapping in the router. • The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of the other ports should be between 1 and 65535 and the value must be different from each other.
  • Page 80 ATM Digital Video Recorder User Manual Caution We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
  • Page 81: Chapter 8 Atm Settings

    ATM Digital Video Recorder User Manual Chapter 8 ATM Settings 8.1 Network Interception The transaction information of ATM, including transaction card No, transaction amount, transaction behaviour, etc., can be captured by monitoring the data package of the network communication. Before You Start Connect the device and the ATM (Automatic Teller Machine) to the network properly.
  • Page 82: Serial Port Protocol

    ATM Digital Video Recorder User Manual Steps 1. Go to System → ATM Settings . 2. Check Enable ATM. 3. Select Input as Network Protocol. 4. Set Interception Port. The interception port is 10000 by default. 5. Select a protocol. 6.
  • Page 83: Configure Transaction Information

    ATM Digital Video Recorder User Manual Figure 8-1 Data Package 2. Set Data Format in Data Package Start Tag. 3. Set Start Tag for the data package according to Data Format. 4. Set Data Format in Data Package End Tag. 5.
  • Page 84: Configure Trigger Channel

    ATM Digital Video Recorder User Manual Figure 8-2 Transaction Information 2. Set Major Type. 3. Set Minor Type. Note When Major Type is set as Transaction Behaviour, 8 minor types are selectable: Card In, Card Out, Overlay, Query, Withdrawal, Deposit, Change Password, and Transfer. 4.
  • Page 85: Configure Overlay Position

    ATM Digital Video Recorder User Manual Figure 8-3 Trigger Channel 2. Select analog camera(s) or IP camera(s) for the text overlay of transaction information and command triggered recording. 3. Check Enable Time Delay. 4. Set Delay Time for menu display if there is no Card In or Card Out in the transaction information.
  • Page 86 ATM Digital Video Recorder User Manual 2. Set whether to overly transaction information on the image. None It will not overlay transaction information on the image. Custom It will overlay transaction information on the image. You can drag the yellow rectangle to a desirable position.
  • Page 87: Chapter 9 File Management

    ATM Digital Video Recorder User Manual Chapter 9 File Management 9.1 Search Files Specify detailed conditions to search videos and pictures. Steps 1. Go to File Management → All Files/Human Files/Vehicle Files . 2. Specify detailed conditions, including time, camera, event type, etc. Note •...
  • Page 88 ATM Digital Video Recorder User Manual Steps 1. Search files to export. 2. Click files to select and click Export. 3. Optional: Check Backup License Plate Statistics Info to export license plate statistics information later. Note Only for vehicle files. 4.
  • Page 89: Chapter 10 User Management And Security

    ATM Digital Video Recorder User Manual Chapter 10 User Management and Security 10.1 Manage User Accounts The Administrator user name is admin and the password is set when you start the device for the first time. The Administrator has the permission to add and delete users and configure user parameters.
  • Page 90: Edit The Admin User

    ATM Digital Video Recorder User Manual 10.1.2 Edit the Admin User For the admin user account, you can modify your password and unlock pattern. Steps 1. Go to System → User . 2. Select the admin user from the list. 3.
  • Page 91: Edit An Operator/Guest User

    ATM Digital Video Recorder User Manual 9. Click OK to save the settings. 10.1.3 Edit an Operator/Guest User You can edit the user information, including user name, password, permission level, and MAC address. Steps 1. Go to System → User . 2.
  • Page 92 ATM Digital Video Recorder User Manual Figure 10-3 User Permission Settings Interface 3. Set the user's operating permissions for Local Configuration, Remote Configuration, and Camera Configuration for the user. 1) Set Local Configuration Local Log Search Searching and viewing logs and system information of device. Local Parameters Settings Configuring parameters, restoring factory default parameters, and importing/exporting configuration files.
  • Page 93 ATM Digital Video Recorder User Manual Remotely viewing logs that are saved on the device. Remote Parameters Settings Remotely configuring parameters, restoring factory default parameters, and importing/ exporting configuration files. Remote Camera Management Remote adding, deleting, and editing of the IP cameras. Remote Serial Port Control Configuring settings for RS-232 and RS-485 port settings.
  • Page 94: Set Live View Permission On Lock Screen

    ATM Digital Video Recorder User Manual Local Video Export Locally exporting recorded files of the selected camera(s). Local Live View View live video of the selected camera(s) in local. 4. Click OK to save the settings. 10.2.2 Set Live View Permission on Lock Screen The admin user can set live view permission for specific cameras in the screen lock status of device.
  • Page 95: Configure Password Security

    ATM Digital Video Recorder User Manual 4. Set the permissions.Select the camera (s) to allow live view when the current user account is in logout status. 5. Click OK. 10.3 Configure Password Security 10.3.1 Export GUID File The GUID file can help you to reset password when you forget password. Please keep it properly. Steps 1.
  • Page 96: Configure Reserved Email

    ATM Digital Video Recorder User Manual Figure 10-6 Configure Security Questions 3. Click OK. 10.3.3 Configure Reserved Email The reserved email will help you to reset password when you forget your password. Steps 1. Check Reserved E-mail when you are activating the device, or click Modify when you are editing the admin user account.
  • Page 97: Reset Password

    ATM Digital Video Recorder User Manual Figure 10-7 Configure Reserved Email 3. Click OK. 10.4 Reset Password When you forget the admin password, you can reset the password by importing the GUID file, answering security questions, or entering verification code from your reserved email. 10.4.1 Reset Password by GUID Before You Start The GUID file must be exported and saved in the local U flash disk after you have activated the...
  • Page 98: Reset Password By Security Questions

    ATM Digital Video Recorder User Manual Note If you have imported the wrong GUID file for 7 times, you will be not allowed to reset the password for 30 minutes. 4. After the GUID file is successfully imported, enter the reset password interface to set the new admin password.
  • Page 99 ATM Digital Video Recorder User Manual a. Insert a USB flash drive to your device. b. Click Export to export the QR code to USB flash drive. c. Email the QR code to pw_recovery@device-service.com as attachment. 6. Check your reserved email, and you will receive a verification code within 5 minutes. 7.
  • Page 100: Chapter 11 System Management

    ATM Digital Video Recorder User Manual Chapter 11 System Management 11.1 Configure Device Steps 1. Go to System → General . 2. Configure the following settings. Language The default language used is English. Output Standard Set the output standard to NTSC or PAL, which must be the same as the video input standard.
  • Page 101: Manual Time Synchronization

    ATM Digital Video Recorder User Manual 11.2.1 Manual Time Synchronization Steps 1. Go to System → General . 2. Configure the date and time. 3. Click Apply to save the settings. 11.2.2 NTP Synchronization Connection to a network time protocol (NTP) server can be configured on your device to ensure the system’s date and time accuracy.
  • Page 102: Network Detection

    ATM Digital Video Recorder User Manual Manually set the start time and end time of the DST period, and the DST bias. 4. Set the DST Bias. Set the time (30/60/90/120 minutes) offset from the standard time. 5. Click Apply to save the settings. 11.3 Network Detection 11.3.1 Network Traffic Monitoring Network traffic monitoring is the process of reviewing, analyzing and managing network traffic for...
  • Page 103: Export Network Packet

    ATM Digital Video Recorder User Manual 3. Enter the destination IP address in Destination Address. 4. Click Test. Figure 11-2 Test Network Delay and Packet Loss 11.3.3 Export Network Packet After the recorder accessing network, you can use USB flash drive to export network packet. Before You Start Prepare a USB flash drive to export network packet.
  • Page 104: Storage Device Maintenance

    ATM Digital Video Recorder User Manual Figure 11-4 Network Resource Statistics 2. View the bandwidth statistics, including IP Camera, Remote Live View, Remote Play, Net Total Idle, etc. 3. Optional: Click Refresh to obtain the latest data. 11.4 Storage Device Maintenance Enter a short description of your concept here (optional).
  • Page 105: Repair Database

    ATM Digital Video Recorder User Manual Note • You can pause/resume or cancel the detection. • After testing has been completed, you can click Error information to see the detailed damage information. 11.4.2 Repair Database Repairing database will rebuild all databases. It might help to improve your system speed after upgrade.
  • Page 106 ATM Digital Video Recorder User Manual Steps 1. Go to Maintenance → Upgrade . 2. Click Local Upgrade to enter the local upgrade interface. Figure 11-7 Local Upgrade Interface 3. Select the firmware update file from the storage device. 4. Click Upgrade to start upgrading. After the upgrade is completed, the device will reboot automatically to activate the new firmware.
  • Page 107: Upgrade Analog Cameras

    ATM Digital Video Recorder User Manual Upgrade by Guarding Vision After logging the device into Guarding Vision, the device would periodically check for the latest firmware from Guarding Vision. If an upgrade firmware is available, the device will notify you when you log in.
  • Page 108: Import/Export Device Configuration Files

    ATM Digital Video Recorder User Manual 4. Click Upgrade. The IP camera will reboot automatically after the upgrading completes. 11.6 Import/Export Device Configuration Files The device configuration files can be exported to a local device for backup; and the configuration files of one device can be imported to multiple devices if they are to be configured with the same parameters.
  • Page 109: Restore Default Settings

    ATM Digital Video Recorder User Manual Figure 11-10 Log Search Interface 2. Set the log search conditions, including the time, major type and minor type. 3. Click Search to start searching the log files. 4. The matched log files will be displayed on the list, as shown below. Figure 11-11 Log Search Results Note Up to 2,000 log files can be displayed each time.
  • Page 110: Security Management

    ATM Digital Video Recorder User Manual Restore Defaults Restore all parameters, except the network (including IP address, subnet mask, gateway, MTU, NIC working mode, default route, server port, etc.) and user account parameters, to the factory default settings. Factory Defaults Restore all parameters to the factory default settings.
  • Page 111: Isapi Service

    ATM Digital Video Recorder User Manual 11.9.2 ISAPI Service ISAPI (Internet Server Application Programming Interface) is an open protocol based on HTTP, which can realize the communication between the system devices (e.g., network camera, NVR, etc.). The device is as a server, the system can find and connect the device. Steps 1.
  • Page 112 UD16604N...

This manual is also suitable for:

Ids-7204ahqhi-m1

Table of Contents