Programming; Operating - White Rodgers 1F97-1277 Installation And Operating Instructions Manual

OPERATING YOUR THERMOSTAT OPERATING YOUR THERMOSTAT
OPERATING YOUR THERMOSTAT OPERATING YOUR THERMOSTAT OPERATING YOUR THERMOSTAT
Choose the Fan Setting (Auto or On or Prog) Choose the Fan Setting (Auto or On or Prog) Choose the Fan Setting (Auto or On or Prog) Choose the Fan Setting (Auto or On or Prog) Choose the Fan Setting (Auto or On or Prog)
Fan A A A A A uto uto uto is the most commonly selected setting and runs uto uto
the fan only when the heating or cooling system is on.
Fan On On On On On selection runs the fan continuously for increased air
circulation or to allow additional air cleaning.
Fan Pr Pr Pr Pro o o o o g g g g g will cycle the fan for -10 minutes on and 20 Pr
minutes off – if the thermostat has not called for heat or cool
during the past 60 minutes.
Choose the System Setting Choose the System Setting Choose the System Setting
Choose the System Setting Choose the System Setting
(Cool, Off, Heat, Auto) (Cool, Off, Heat, Auto)
(Cool, Off, Heat, Auto) (Cool, Off, Heat, Auto) (Cool, Off, Heat, Auto)
Press the SYSTEM button to select:
Hea Hea Hea Heat t t t t : Thermostat controls only the heating system. Hea
Of Of Off f f f f : Heating and Cooling systems are off. Of Of
Cool Cool Cool: Thermostat controls only the cooling system. Cool Cool
A A A A A uto uto uto
uto uto: Auto Changeover is used in areas where both heating
and cooling may be required on the same day. A A A A A UT
the thermostat to automatically select heating or cooling
depending on the indoor temperature and the selected heat
and cool temperatures. When using A A A A A UT
Cooling temperatures more than 1° Fahrenheit higher than
the heating temperature.
Manual Operation for Manual Operation for
Manual Operation for Manual Operation for Manual Operation for
Non-Programmable Thermostats Non-Programmable Thermostats Non-Programmable Thermostats Non-Programmable Thermostats Non-Programmable Thermostats
Pr Pr Pr ess ess
Press Pr ess ess the SYSTEM button to select Heat or Cool and use
the or buttons to adjust the temperature to your
desired setting. After selecting your desired settings you can
also press the SYSTEM button to select AUTO
the thermostat to automatically change between Heat and
Cool.

PROGRAMMING

PROGRAMMING PROGRAMMING
PROGRAMMING PROGRAMMING
Set Current Time and Day Set Current Time and Day Set Current Time and Day Set Current Time and Day Set Current Time and Day
1) Press Menu key to enter installer menu. Then press
Set Time once to indicate hour & A or P designation in
clock display.
2) Press and hold either the
reach the correct hour and A or P designation.
3) Press Set Time again to display minutes only in clock
display.
4) Press and hold either the
reach the correct minutes.
5) Press Set Time once again to display year.
6) Press and hold either the
reach the correct year.
7) Press Set Time once again to display month.
8) Press and hold either the
reach the correct month.
9) Press Set Time once again to display date of the month
along with day of the week at top row (which is auto-
matic).
10) Press and hold either the
reach the correct day of the month and day of the week
is automatically calculated and displayed at the top row.
11) Press Run Schedule once; now the display will show the
correct time and room temperature.
8
UT UT UT UTO O O O O allows
UT UT UTO O O O O , be sure to set the UT
AUTO AUTO AUTO to allow AUTO
or touch key until you
or touch keys until you
or touch key until you
or touch key until you
or touch key until you
IMPORTANT! IMPORTANT!
IMPORTANT! IMPORTANT! IMPORTANT!
Manual Operation (Bypassing the Program) Manual Operation (Bypassing the Program)
Manual Operation (Bypassing the Program) Manual Operation (Bypassing the Program) Manual Operation (Bypassing the Program)
Programmable Thermostats Programmable Thermostats Programmable Thermostats Programmable Thermostats Programmable Thermostats
Press or and the HOLD button and adjust the tempera-
ture wherever you like. This will override the program. The
HOLD HOLD
HOLD feature bypasses the program and allows you to HOLD HOLD
adjust the temperature manually, as needed. Whatever
temperature you set in HOLD HOLD will be maintained 24 hours a HOLD HOLD HOLD
day, until you manually change the temperature or press R R R R R un
Sc Sc Schedule hedule to cancel HOLD hedule hedule HOLD HOLD and resume the programmed HOLD
Sc Sc hedule HOLD
schedule.
Program Override (Temporary Override) Program Override (Temporary Override) Program Override (Temporary Override) Program Override (Temporary Override) Program Override (Temporary Override)
Press or buttons to adjust the temperature. This will
override the temperature setting for a (default) four hour
override period. The override period can be shortened by
pressing or lengthened by pressing
period can range from 15 minutes to 7 days.
Example Example: If you turn up the heat during the morning pro- Example
Example Example
gram, it will be automatically lowered later, when the tempo-
rary hold period ends. To cancel the temporary setting at any
time and return to the program, press R R R R R un Sc
If the SYSTEM button is pressed to select AUTO
thermostat will change to Heat or Cool, whichever ran last. If
it switches to heat but you want cool, or it changes to cool
but you want heat, press both
neously to change to the other mode.
Automatic Daylight Saving Calculation Automatic Daylight Saving Calculation Automatic Daylight Saving Calculation Automatic Daylight Saving Calculation Automatic Daylight Saving Calculation
The Real Time Clock will adjust automatically for daylight
savings time, in the following manner:
Increment one hour at 2 AM on the second Sunday of March
and decrement one hour at 2 AM on the first Sunday of
November. (New DST effective 2007).
The daylight saving feature can be enabled or disabled in
installer configuration mode. Default is dS ON
After entering installer configuration mode, momentarily
press or touch key until the display indicates dS
actual temperature digits) and on (default – in clock digits).
and keys will toggle display and operation from on to
OFF .
Programming Tip: Copy Button Programming Tip: Copy Button Programming Tip: Copy Button Programming Tip: Copy Button Programming Tip: Copy Button
You may copy any daily program to another day or group of
days by pressing the Copy button. In 7 day programming
mode when the Copy button is pressed, the other 6 days of
the week will flash. To copy the current program into the
remaining six days, simply press the Copy button again. To
copy the current program to another day of the week, press
Advance Day to select the day and press Copy to paste the
program. In 5/1/1 day programming mode the copy function
is similar. The weekday (Mon-Fri) program can be copied to
Sat and Sun (both flashing) or use Advance Day to choose
Sat or Sun and press the Copy button to paste the program.
un un un un
. Program Override
un Schedule un Sc un Sc un Sc hedule hedule hedule. hedule
AUTO AUTO AUTO the AUTO
or or or or or
buttons simulta-
dS ON (enabled). dS ON dS ON
dS ON
dS (in dS dS dS