Table of Contents
Advertisement
THERMOSTAT QUICK REFERENCE
Home Screen Description
Note: If
is displayed, the
thermostat is battery powered.
When battery power remaining
is approximately half,
be displayed. If the home is
going to be unoccupied for an
extended period (over 3 months)
and
is displayed, the batteries
should be replaced before leaving.
Programming and Confi guration Items
Displays
and "Keypad Lockout" when in keypad
1
lockout mode.
Displays
and "Temperature Limit" and "Keypad
Lockout" when limited range is activated and locked.
Displays only "Temperature Limit" when limited range
is activated.
2
Indicates period of day being programmed.
3
RUN SCHEDULE (run program) key.
SET TIME key or HOLD temperature key.
4
Displays "Change Filter"/"Change Pad"/"Change UV
5
Lamp" when the system has run for the programmed
fi lter/humidity pad/UV lamp time period as a reminder
to change or clean your fi lter/humidity pad or to replace
UV lamp.
6
COPY key or INSTALLER CONFIG key.
CLEAN DISPLAY key allows 30 seconds to wipe off
7
the display or ADVANCE DAY key for programming.
Used in programming to set time and in confi guration
8
menu to change selections.
"Hold Until" indicates the time when a temporary hold
9
period will end.
"Hours" and "Days" displays during steps in installer
10
confi guration.
The words "Hold At" are displayed when the
11
thermostat is in the HOLD mode. "Temporary Hold
At" is displayed when the thermostat is in a temporary
HOLD mode.
"Humidity" indicates that the "Set At" display is Hu-
12
midity setpoint.
"System On" indicates when heating or cooling stage
13
is energized. "+2" indicates when a second stage is
energized.
"Copy" indicates the copy program feature is being
14
used during programming.
Figure 8 – Home Screen Display
Time of Day
System
Switch
will
Fan
Switch
Indicates when
thermostat is calling
for Heat or Cool
Room
Temperature
Day of Week
Battery Level Indicator
Indicating the current power level
of the 2 "AA" batteries.
Full power remaining.
Half power remaining.
Change
The batteries should be replaced at this time.
Figure 9 – Programming & Confi guration Items
16
17
10
1
1
1
1
1
2
3
4
5
6
7
8
9
0
1
2
3
9
8
18
14
13
15
19
7
A steady "Cool Savings" display indicates the feature
15
is enabled in the installer menu. A fl ashing "Cool
Savings" display indicates the feature is active.
"Remote" indicates that the indoor remote temperature
16
sensor, is being accessed. "Outdoor Remote" indi-
cates the outdoor remote temperature sensor is being
accessed.
17
Display time, remote temperature or humidity.
"Heat Pump" displays when the system confi guration
18
is set in HP1/HP2.
"Call for Service" indicates a fault in the heating/cooling
19
systems. It does not indicate a fault in the thermostat.
Auto Schedule key for Auto Schedule function or
20
Humidity key to display current Humidity and Humidity
setpoint.
Set Temperature/Humidity
Temperature
UP/Down used for
modifying setpoint
as well as to
navigating the menus
Press to view
Humidity setpoint
Menu key for entering
different modes such as
Cleaning, Configuration, Set
Time and Set Schedule
11
12
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
5
6
4
3
9
1
2
20
3
5
Hide quick links:
Advertisement
Table of Contents
