Advertisement
Closet installation
25
n
Determine
the length
of
exhaust
duct that is needed
to-connect
the
dryer to the exhaust
hood. See "Exhaust
requirements,"
Panel B.
-
26.
n
Remove
tape from dryer
Connz
Ghaust
'
door and open dryer door. Remove
tape
across the dryer lint screen.
Check
to be sure
duct to washer/dryer
lint screen is in its proper
position.
Wipe out
and then to the
drum with a damp
cloth to remove
any dust.
exhaust
hood.
Start drver and allow it to complete
a heat
closet
door
24
sq. In. (155 sq. cm)
-IT
l
Use the straightest
path possible
to avoid
90" turns.
l
Use duct tape
to
seal
all
joints in the
exhaust
system.
l
Use caulking
compound
to seal exterior
wall opening
around
exhaust
hood.
27
n CHECK ELECTRICAL
REQUIREMENTS. BE SURE YOU HAVE CORRECT
ELECTRICAL SUPPLY AND RECOMMENDED
EARTHING METHOD.
Check
the Installation
Instructions
to see that
you have completed
each
step. Complete
any missed steps before
you continue.
cycle
t6 make sure the dryer is working
properly.
T
I'
front view
Unobstructed
air openings
are minimum
for closet
door. Louvered
door with equivalent
air openings
36
n
Finally, save all literature
and
is acceptable.
*(r'
(0
cm)
Additional
space
may
be needed
for exhaust
elbow.
'I)
1
48
sq. In.
(310
sq. cm)
T
keep with washer)dryer.
I_
1" (2.5 I
To get the most efflclent use from
your new Whlrlpool washer/dryer,
closet
door
-
24
sq. In.
(155
sq. cm)
f
4
( Congratulations! 1
Keep lnstallatlon lnstructlons nearby
~~~~
side view
Closet installation
must be exhausted
outdoors.
Recessed,
non-exhausted
installation
must use
only the rear exhaust
position
and Exhaust
Deflector
Kit No. 4500 is required.
2U.
Ir
~-
~ Check
that all parts are now
lstalled.
See parts list, Panel 8. If there is an
extra part, go back through
the steps to see
Recessed and closet
installation instructions
Product dimensions
(Shown with legs extended
1 Inch (2.5 cm)
tram bottom of washer/dryer.)
which step was skipped.
lT(30.5
cm)
r
Fire Hazard
l
It Is recommended
that the
washer/dryer
be exhausted to the
outslde.
l
It washer/dryer
Is Installed In a closet,
the dryer MUST be exhausted outslde.
Failure to do so may result In a tire.
lY'(30.5
cm
29
w-w-
H Check
that you removed
all the
TO PREVENT LARGE AMOUNTS OF LINT AND
MOISTURE FROM ACCUMULATING IN THE
RECESSED AREA, TO MAINTAIN DRYING
EFFICIENCY, AND TO PREVENT EXPOSURE TO
POSSIBLE HEALTH HAZARDS, THIS APPLIANCE
SHOULD BE EXHAUSTED OUTDOORS.
This washer/dryer
may be installed in a
recessed area or closet.
The installation
spacing
is in inches and
centimeters
and is the minimum
allowable.
Additional
spacing
should be considered
for
ease of installation,
servicing
and
compliance
with local codes and
ordinances.
If closet door is installed,
the minimum
unobstructed
air openings
in top and
bottom
are reauired.
Louvered
doors with
equivalent
air dpenings
are acceptable.
Closet installation
must be exhausted.
Other installations
must use the minimum
shipping
pieces,
including
the three shipping
straps with keys. Dispose of all materials
in
proper
manner.
It you do not remove all three shlpplng
straps, your washer/dryer
may "walk" away
from Its locatlon.
(36.2
cm)
recess
width
rear view
dimensions
indicated.
Recessed installation
I
O;(O
cm)
I
*
4-R
(r' (0 cm)
3" (7.6 cm) j
n
I
I I dryer I I
31
12"
(30.5 cm)
WTum on water faucets
and
check
for leaks. Tighten couplings
if there is
leaking.
DO NOT OVERTIGHTEN.
This could
cause damage
to faucets.
washer
sure to tighten
icrews
at each
of the
access
panel.
33
H Plug power
supply cord into
I
I
I
front view
side view
earthed
outlet.
Mlnlmum lnstallatlon spacing
27-l/('
-
(69.2 cm)
34
n
Read the Use and Care Guide
to fully understand
your new washer/dryer.
Now start the washer and allow it to
complete
the regular
cycle.
Note: If recessed
installation
is exhausted,
all
spacing
can be 0 inches
(0 cm).
Additional
clearance
for wall, door and floor
molding
may be required.
Panel E
side view
Advertisement
