Advertisement
Available languages
Available languages
WARNING
- "Risk
of Fire"
- Clothes dryer installation
must be performed
by a qualified
installer.
- Install the clothes dryer according
to the manufacturer's
instructions
and local codes.
- Do not install a clothes dryer with flexible
plastic venting materials,
if flexible
metal
(foil type) duct is installed,
it must be of a specific type identified
by the appliance
manufacturer
as suitable for use with clothes dryers.
Flexible venting materials
are
known to collapse,
be easily crushed,
and trap lint. These conditions
will obstruct
clothes dryer airflow
and increase the risk of fire.
- To reduce the risk of severe injury or death, follow
all installation
instructions.
- Save these instructions.
INSTALLATION INSTRUCTIONS
Gather the required tools and parts before starting installation. Read
and follow the instructions provided with any tools listed here.
Parts needed
for washer
{not provided):
[]
Inlet hoses
[]
Flat washers
To order:
[]
Call the dealer from whom you purchased your washer/dryer.
[]
Call the toll-free number listed on the cover of the Washer/
Dryer User instructions.
[]
Visit the website listed on the cover of the Washer/Dryer
User instructions.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Record hose installation or replacement dates for
future reference.
Tools needed:
[]
#2 Phillips and flat-blade
[]
Caulking gun and
screwdriver
compound (for installing
[]
Adjustable wrench that
new exhaust vent)
opens to 1" (25 mm) or
[]
Level
%d' open-end wrench
[]
Knife
(for adjusting washer/dryer
feet)
[]
Vent clamps
[]
1_,,nut driver or socket
[]
Pliers
wrench
[]
Scissors
[]
Tin snips (for new vent
[]
Wood block (for leveling)
installations)
[]
Ruler or measuring tape
Parts supplied:
Remove parts package from the washer basket. Check that all
parts were included.
Parts needed:
Check local codes. Check existing electrical supply and venting,
and see "Electrical Requirements" and "Venting Requirements"
before purchasing parts.
Mobile home installations require metal exhaust system hardware
available for purchase from the dealer from whom you purchased
your washer/dryer. For further information, please reference the
"Assistance
or Service" section of the Washer/Dryer User
Instructions.
Your installation may require additional parts. For information on
ordering, please refer to the toll free phone numbers on the front
page of the Washer/Dryer
User Instructions.
if You Have
You Will Need to Buy
Laundry tub or
Sump pump system (if not already
standpipe taller than
available)
96" (2.4 m)
1" (25 mm) diameter
standpipe
2" (51 mm) diameter to 1" (25 mm)
diameter standpipe adapter, Part
Number 3363920
Overhead sewer
Standard 20 gal. (76 L) 34" (864 mm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain
Siphon break, Part Number 285320,
additional drain hose, Part Number
285702 and connector kit,
Part Number 285442
Drain hose too short
Drain hose, Part Number 285664 and
connector kit, Part Number 285442
Lint clogged drain
Drain protector, Part Number 367031
Water faucets
2 longer water fill hoses:
beyond reach of fill
6 ft (1.8 m) Part Number 76314,
hoses
10 ft (3.0 m) Part Number 350008
A
B
C
D
E
A. Rear leveling legs (2)
D. Plastic strap
B. Front leveling legs (2)
E. Silver double-wire hose clamp
C. Drain hose
2
Advertisement
