H3C S12500 Series Quick Installation Manual
Routing switch
Hide thumbs
Also See for S12500 Series:
- Installation manual (170 pages) ,
- Installation instructions manual (126 pages) ,
- Configuration manual (59 pages)
Subscribe to Our Youtube Channel
Related Manuals for H3C S12500 Series
Summary of Contents for H3C S12500 Series
- Page 1 H3C S12500 Routing Switch Series Quick Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: APW201-20131030...
- Page 2 Copyright © 2013, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd.
-
Page 3: Table Of Contents
Contents Quick installation guide ··············································································································································· 1 Preparing for installation ·················································································································································· 1 ESD prevention ························································································································································· 1 Examining the installation site ································································································································· 2 Installation tools and accessories ··························································································································· 2 Installing the switch ··························································································································································· 2 Removing the power frame mounting bracket ······································································································ 3 ... -
Page 4: Quick Installation Guide
Quick installation guide This quick installation guide provides basic instructions for installing an S12500 routing switch. For more detailed installation procedures, see H3C S12500 Routing Switch Series Installation Guide. Preparing for installation ESD prevention To prevent the electronic components from being damaged by the electrostatic discharge (ESD), always wear an ESD wrist strap when you touch the switch, cards, or ICs, and make sure the wrist strap is correctly grounded. -
Page 5: Examining The Installation Site
Examining the installation site The H3C S12500 Routing Switch Series can only be used indoors. To make sure the switch operates correctly and to prolong its service lifetime, the installation site must meet the load-bearing, temperature, humidity, cleanness, EMI, grounding, power module, and space requirements. For more information, see... -
Page 6: Removing The Power Frame Mounting Bracket
Removing the power frame mounting bracket Before you mount the switch in a rack, remove the power frame mounting bracket with a Phillips screwdriver. Figure 3 Removing the power frame mounting bracket Installing the switch in a rack Check before installation Before installation, make sure the bottom edge of the slide rails or rack shelf aligns with the middle of the narrower metal area between holes. - Page 7 on the mounting bracket (each installation hole on the mounting bracket corresponds to one cage nut). Insert one edge of a cage nut into the hole. Compress the other edge of the cage nut to push the cage nut fully into the hole. Repeat steps 2 and 3 to install cage nuts to all the marked positions on the right rack post.
-
Page 8: Grounding The Switch
Grounding the switch Remove the two grounding screws from the switch chassis. Use the grounding screws to attach one end of the grounding cable to the chassis. Connect the other end of the grounding cable to the grounding strip of the rack in the same way. Figure 7 Connecting the grounding cable Installing the power modules AC and DC power modules are installed in the same way. -
Page 9: Installing A Fan Tray
Figure 8 Installing a power module (on an S12508) Install other power modules by repeating steps 1 to 4, and close the power frame panel. Figure 9 Closing the power frame panel (on an S12508) Installing a fan tray Each of the S12508 and the S12518 has two fan trays. They are installed in the same way. To install a fan tray: Remove the blank panel from the slot to be used. -
Page 10: Installing A Card
Fasten the captive screws on the front panel of the fan tray. Figure 11 Installing a fan tray (for the S12508) Installing a card Slot requirements Install MPUs, LPUs, and switching fabric modules into appropriate slots as shown in Figure NOTE: On an S12508 or S12518 switch, install at least one MPU, one interface card, and seven switching fabric modules. - Page 11 Figure 12 Slot requirements (for the S12508) (1) MPU slots (with red edges) (2) LPU slots (with blue edges) (3) Switching fabric module slots (with grey edges) Installing a card This section describes how to install an MPU as an example. To install an MPU: Remove the protective cover before installing an MPU: Put on an ESD wrist strap and then loosen the captive screws that fix the MPU to the protective...
- Page 12 Figure 13 Removing the protective cover NOTE: Protective cover appearance varies with models. You can remove a protective cover of any model by using the same way illustrated in this document. Move the ejector levers on the front panel of the MPU outwards, hold up the MPU by one hand without touching any electronic components on the MPU, and hold the front panel by the other hand to push the MPU into the slot along the slide rails slowly.
-
Page 13: Connecting Power Cords
16 A power cord (AC), so you need to use a 16 A busbar, and make sure the AC power supply system can H3C S12500 provide enough power. For 16 A AC power cords used in different countries or regions, see... - Page 14 Figure 15 Installing the power cable bracket Insert the AC power cord into the power receptacle. Use a cable tie to secure the power cord to the tie-wrap tab on the power cable bracket. Repeat steps 2 and 3 to secure other AC power cords to the power cable bracket. Connect the other end of the AC power cord to the power source.
-
Page 15: Verifying The Installation
Connect one end of the black DC power cord to the RTN(+) terminal on the power strip, and fasten the screw. Figure 17 Connecting the DC power cord to the grounding strip Connect the other end of the DC power cord to the power source: Connect the other end of the blue DC power cord to the –48 VDC power source. -
Page 16: Logging In To The Switch
Table 1 Installation checklist Result Item Remarks The grounding cable is correctly grounded. Fan trays are correctly installed and make close contact with the backplane. Power modules are correctly installed and have close contact with the frames. The power switch is off (the power switch is at the OFF position). -
Page 17: Powering On The Switch
Figure 19 Connecting the console cable Powering on the switch Verify that the power cord is connected to the power source, power on the switch, and verify that the LEDs on the switch are normal. Table 2 LED description when the switch is operating correctly Module Status SFC (red/green) -
Page 18: Obtaining Documentation
H3C S12500 Routing Switch Series Installation Guide For more information about the LEDs, see Obtaining documentation Take the following steps to get related documents from the H3C website at www.h3c.com. Go to http://www.h3c.com/portal/Technical_Documents. Choose the desired product category and model. -
Page 19: Index
Removing the power frame mounting bracket,3 Grounding the switch,5 Verifying the installation,12 Installation tools and accessories,2 Installing a card,7 Copyright © 2013, Hangzhou H3C Technologies Co., Ltd. For more information about the product and installation procedures, log in to www.h3c.com...
Need help?
Do you have a question about the S12500 Series and is the answer not in the manual?
Questions and answers