ISS 5, SECTION 503-603-I01
• Line key (635BT5), 6-button
key.
Hold with
Note:
Write
date
of installation
on label
five line pickup buttons
which are convertible
provided
on battery.
to nonlocking.
An
additional
momentary
contact
(logic
reset
switch)
is attached
to
3.03
Install
the 95B1 power
unit within
150 feet
the Hold side of the key to reset
the
logic
(24 gauge
conductors)
of the
telephone
set
circuit
anytime
a key button
is depressed,
and plug into an ac outlet not controlled
by a switch
(continuous
ac power
is required).
A retaining
• 32-button
array
of low
force,
low
travel
clamp (841050818) will be shipped
with the 95B-type
nonlocking
memory buttons
arranged
in three
power
unit
and
should
be
mounted
to
the
ac
columns.
Left and right columns
have eleven
receptacle
to hold power
unit securely
and prevent
buttons,
center
column
has ten buttons,
accidental
loss of power.
The power
unit may be
located
at the equipment
end of the cable or run
• LAST NUMBER
DIALED
button
located
in
directly
into
the
telephone
set
by
conductors
lower
right
corner
of memory
array,
when
separate
from the mounting
cord and connected
to
momentarily
depressed,
automaticallyredials
PSB
terminals
30 and
31.
Refer
to applicable
the last
number
manually
dialed,
tables
and Fig. 8 for particular
type of installation.
When separate
power conductors
are used, disconnect,
• RECORD button (nonlocking), when momentarily
insulate,
and store the (BL-V) and (V-BL) mounting
depressed,
lights
the
RECORD
lamp
and
cord leads
from
PSB terminals
30 and 31.
enables the memory circuits
to store telephone
numbers.
Danger:
Securely
attach
retaining
eIamp
to
ae
outIet
using
outlet
cover
• RECORD
OFF
button
(nonlocking),
when
screw
BEFORE
attempting
to
instaIl
momentarily
depressed
extinguishes
the
95B1
power
unit.
OThe
power
unit
RECORD
lamp, indicating
that the dialer
is
and
any
other
cord
plugged
into
the
switched
out of the record
mode.
ae
outlet
should
always
be
unplugged
completely4
from
the
outlet
BEFORE
• WAIT button(nonlocking),whenmomentarily
attempting
to
attach
or
remove
the
depressed
during
recording
operation,
enters
retaining
clamp.
This
will
prevent
a code
into
memory
to initiate
a halt
in
the
possibiIity
of
a loosened
retainer
the automatic
dialing
sequence
[used where
clamp
or metallic
outlet
cover
making
access
digit(s)
required],
contact
with
the
ae
prongs
of
the
power
unit
when
partially
withdrawn
from
outlet.
Do
not
use
retaining
3.
INSTALLATION
clamps
on
outlets
where
the
cover
mounting
screw
holds
the
duplex
outlet
STANDARD INSTALLATION
in
the
box.
3.01
Make all wiring
changes
and telephone
set
SWarning:
Care
should
be
taken
to
modifications
(Table
A)
before
external
trim
and
dress
leads
connecting
to
connections
are made
to the set (paragraph
4.01).
low
voltage
output
terminals
of
95B1
power
unit
to
assure
that
inadvertent
Warning:
Do not plug
in either
battery
connection
to
conducting
surfaces
or
or
power
unit
until
all
connections
other
power
source
does
not
occur.
and
modifications
are
completed.
Take
If
more
than
one
power
unit
is
extreme
care
not
to
damage
the
plugged
into
a
multiple
receptacle
exposed
components,
circuit,
etc.
when
power
strip,
there
must
be
at
least
the
set
is opened,
one
inch
separation
between
power
units.
Only
UL
listed
receptacle
3.02
The
set is shipped
from
the
factory
with
power
strips
with
adequate
power
the
battery
disconnected.
After
all wiring
rating
shall
be
used.
Use
of
a
changes
and
modifications
have
been
completed,
continuous
terminal
power
strip
that
connect
the battery
(Fig.
7) by tilting
the
set up,
allows
the
secondary
output
terminals
and inserting
the battery
plug into the mating
jack.
of
the
power
unit
to
be
in
close
Page 7
Need help?
Do you have a question about the TOUCH-A-MATIC 2872A1M and is the answer not in the manual?