This is a MODBUS and CANBUS networked system. following standards: The STIIC PLC is designed to work with unit controllers, U .S .A . not to replace them. While the STIIC PLC allows you to monitor and perform basic actions for the devices –...
General Information STIIC Controller 2 .1 STIIC PLC LCD Display The STIIC PLC has an integrated LCD display with six buttons for moving through the menus. This section describes the LCD display buttons. e e e 2 Touchscreen Display 1 LCD Display Buttons...
2 .3 Inputs and Outputs The STIIC PLC allows you to connect different Dometic devices and has outputs to display the information received by the devices. Figure 3 illustrates the STIIC PLC I/O layout. 3 STIIC PLC I/O Layout PLC Input Table 2 .3 .1 PLC Inputs...
STIIC PLC. Units on Device Add STIIC If a temperature sensor is defective or not connected, 1 (Master PLC) the STIIC PLC generates an alarm for that sensor. Platinum Chillers 2 (Slave PLC) PLC Output Table VARC Chiller XTC Seawater...
4 Specifications PLC Technical Specifications Physical This section describes the display, electrical, environmental, and physical specifications for the STIIC Dimensions (H x W x D) 4.4 in. x 8.96 in. x 2.4 in. (110 mm x 227.5 mm x 60 mm) PLC components: Touchscreen display, LCD display, and electric box.
Installation and Setup STIIC Controller 6 Installation and Setup Connection Port Table This STIIC PLC is set up with basic factory defaults, so the Dometic Devices Connection to STIIC PLC control requires configuration to match the constraints of Platinum Chiller MODBUS Communication the devices that are installed in the vessel.
STIIC Controller Installation and Setup 6 .3 Configuring the STIIC PLC Configuring the STIIC PLC is a several step process. To give the STIIC PLC recognition of the devices available for control, you must enable the devices installed on the vessel and disable the devices that are absent from the vessel.
Page 12
16 Device Naming - Room Controls Screen control display. 4. Tap the configuration icon to return to the STIIC Configuration screen. 5. Tap KRA Naming. 6. Use the KRA drop-down menu to select a KRA name.
Page 13
VNC Viewer app. up the Remote Support VNC Viewer 6. To end remote access, select Stop on the Control The remote support screen allows you to set up the STIIC tab. PLC to be accessed by Dometic technical support.
Page 14
(0=disabled, 1=enabled). 6 .3 .7 Using the LCD Display to Assign IP Addresses The STIIC PLC can be setup to have a static IP address for network configurations. 1. Press and hold Alarm and Enter for five seconds or 24 Device Enabled Screen until the screen goes to the PLC menu.
32 Update Configuration Screen 7 Operation This section describes the features available for control of the devices tied to the STIIC PLC. 7 .1 Accessing a Device Type 34 Air Conditioning Main Screen From the Main screen, select the icon of the type of The Chiller Menu displays.
Page 16
Operation STIIC Controller 35 Chiller Main Menu 37 Air Conditioning Main Screen This is the main screen for room controls. Tap the specific Live Supply and Mode of Operation room to view details or use Global Control to set the...
STIIC Controller Operation – Off – Auto – Setpoint (manual adjustment) To manually adjust the setpoint: a. Tap the SETPOINT value box (the initial value reads 0 °F). A keypad appears. 41 KRA Main Menu Screen The main KRA menu appears listing the enabled condensing units.
ESKIMO ICE. 43 Keypad 2. Enter the desired setpoint value. 3. Tap OK. The STIIC PLC records a log of the temperature inside each KRA box. Select the Trend icon to open the trend graph. 45 Eskimo Ice Main Screen The main Eskimo Ice screen appears listing the available Eskimo Ice machines.
To access the SeaXchange control from the Main screen, technician to modify the parameters of the system. These tap REVERSE OSMOSIS and tap Sea X Change. options require a password to access. Only Dometic approved technicians can access these options.
Page 20
• View the amount of water produced. 52 XZ Series Main Screen 7 .6 .2 Using the ZTC SpotZero The combination XZ system from the STIIC PLC is a To access the SpotZero controls from the Main screen, combination of the XTC watermaker and the ZTC tap REVERSE OSMOSIS and tap Spot Zero.
Alarms 8 Alarms The Historical Alarms screen displays all recorded alarms. The STIIC PLC provides an alert if any device connected to it has a fault. 8 .1 Using the Touchscreen to View Alarms The touchscreen program uses the flashing bell icon to represent that there is a fault.
3. Scroll through the alarms to identify the faulted COM/WARRANTY. device. IF YOU HAVE QUESTIONS, OR TO OBTAIN A COPY – AL on STIIC is a global alarm indicating that at OF THE LIMITED WARRANTY FREE OF CHARGE, least one system device has a fault. CONTACT: –...
Page 24
YOUR LOCAL YOUR LOCAL DEALER SUPPORT SALES OFFICE dometic .com/dealer dometic .com/contact dometic .com/sales-offices A complete list of Dometic companies, which comprise the Dometic Group, can be found in the public filings of: DOMETIC GROUP AB Hemvärnsgatan 15 SE-17154 Solna Sweden...