Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mark FBA
Summary of Contents for Mark FBA
- Page 1 Technical manual...
-
Page 3: Table Of Contents
Specifications condensate pump Electrical connection condensate pump Mounting Commissioning Maintenance Maintenance Warranty Motor Heat exchanger Air filter Decommissioning - Disassembly 10.1 Decommissioning 10.2 Disassembly Tanner FBA 10.3 Disassembly Tanner FBA Ultra 10.4 Disassembly Tanner FBA-K Ultra 10.5 Removal and destruction... -
Page 4: Intended Use
Consultation with or consent of the manufacturer is necessary for differents type of use. Tanner FBA devices that are used for transporting flammable or explosive gasses, vapors, mists or dusts must be specifically designed. Standard Tanner FBA devices may not be used in hazardous... -
Page 5: Safety
Before assembly, commissioning and/or maintenance we refer to this technical manual. Failure to comply with the technical manual can cause personal harm and malfunction of the device. Note: The Tanner FBA device may only be maintained when: • The isolation switch is connected;... -
Page 6: Receiving Of The Goods
Please note that the packaging may not be contaminated and must be seperated into groups. Mounting 4.1 Ceiling mounting Fastening the FBA device to the ceiling must be done with officially approved fasteners. In the dimensioning of the fastening the following gear weights should be taken into account. Type A (mm) -
Page 7: Mounting Suction Accessories
4.2 Mounting suction accessories On the FBA device acessories can be mounted on the suction side. For this, an intermediate frame is required. Connection of each component: On a frame profile a sealing strip of 8x3mm has to be adhered per connection flange. -
Page 8: Connection Cables
4.5 Connecting cables Do not turn the connector (This will destroy the heat exchanger. No warranty.) Attach the heating supply lines to the supply & return of the heat exchanger with a suitable tool. Make use of a gate valve for the heat exchanger so you can easily reach this during later maintenance work. -
Page 9: Electrical Connection
Electrical connection Parallel connection of FBA devices Switching unit 670 - 671 Switching unit 685/52-54 E 9-wire 5-wire 9-wire 9-wire 5-wire 5-wire Fan engine 1 TK=Thermocontact Fan engine 2 o. X TK=Thermocontact Fan engine 1 TK=Thermocontact Fan engine 2 o. X... -
Page 10: Switchgear
Maximum number of FBA devices on a switching device Switchgear FBA 601 FBA 701 FBA 801 FBA 603 FBA 703 FBA 803 685 / 52E 685 / 53E 685 / 54E 685 / 55D 685 / 56D 685 / 57D... - Page 11 5-speed switching device, 5 speeds 400V (Engine 001) 5-wire Location supply fuses FS=Frost protection thermostat RT=Room thermostat TK=Thermocontact 5-speed switching device, 5 speeds 230V (Engine 003) 685/52-53E 250 V AC 250 V AC max. 2A max. 1A RT=Room thermostat 3-wire TK=Thermocontact Location supply...
- Page 12 Switchgear with servomotor 515 Switchgear with actuator on/off 517 Switching unit Position “0“ Position “0“ Servomotor Servomotor Position „Closed“ Position „Closed“ Switchgear with control unit 707 Switchgear with room thermostat and actuator on/off 517 685 / 52-53 E 14 12 230 V / 50 Hz 685 / 54 E 14 12...
-
Page 13: Commissioning
Commissioning The nominal power is indicated on the nameplate. AC motors that have been designed for a nominal power of 400V can be used in the range of 400V + 6 / -10% in accordance with DIN/IEC 38. Also in accordance with this, single-phase motors can be used in the range of 230V 6+/-10%. Connection EVA ethylene vinyl acetate 4 GJ1 according to VDE 0208 / 3.69. - Page 14 Electrical work may only be done by a qualified installer. • An isolator switch must be installed on every device in order to shut off the engine. • Only turn on the engines when the outlet and protective louvres have been opened. •...
-
Page 15: Cooling
Cooling 8.1 Air heaters for heating and cooling Units FBA-K Ultra 630, 730 and 830 are suitable for cooling also. In this case a unit is equipped with an additional drip tray [1] and a condensate pump [2]. The units are fully connected with hoses and electrical wiring. -
Page 16: Electrical Connection Condensate Pump
Pump running time (standard) Pump float switch (special) 8.4 Mounting The FBA Ultra must be installed absolutely horizontal or with a slight slope of 1mm for the condensate pump. 8.5 Commissioning Free the condensate tray of dust and other contaminants. Before commissioning the operation of the condensate pump must be checked. -
Page 17: Motor
In addition, regular maintenace is required for: • VDI 6022 - Hygienic standards for ventilation and air-conditioning • VDI 3801 - Exploitation of air conditioning systems • VDMA 24186 - Performance program for maintenance of air conditioning and other technical equipment in buildings, air handling units and equipment •... -
Page 18: Disassembly Tanner Fba
9. Pull the heat exchanger from the unit. 10. Move both halves by moving vertically. 10.3 Disassembly Tanner FBA Ultra 1. Turn off the main switch and lock it. 2. Remove the power supply and electrical connection in the junction box “K”. -
Page 19: Disassembly Tanner Fba-K Ultra
In the handling of dust-sensitive components (filters) and parts of mineral wool it is wise to wear appropriate respiratory protection. Destruction In our FBA devices, the following material is used: Housing and attachments: • Galvanized steel •... - Page 20 FAX +31 (0)598 624584 TELEFAX +49 (0)2822 97728-10 info@mark.nl info@mark.de www.mark.nl www.mark.de MARK EIRE BV MARK POLSKA Sp. z o.o COOLEA, MACROOM UL. KAWIA 4/16 CO. CORK (IRELAND) 42-200 CZE ˛STOCHOWA (POLSKA) PHONE +353 (0)26 45334 PHONE +48 34 3683443...
Need help?
Do you have a question about the FBA and is the answer not in the manual?
Questions and answers