Operation; Replacing The Power Cable - EINHELL TH-TS 820 Original Operating Instructions

6.4 Replacing the table insert (Fig. 4)
•
Important: Pull out the power plug!
•
Remove the 6 screws (23).
•
Take off the saw blade guard (2) (see 6.3).
•
Lift the worn table insert (6) up and out.
•
Fit the replacement table insert by following
the above in reverse.

7. Operation

7.1 Switching On and Off (Fig. 1)
•
The saw can be switched on by pressing the
green pushbutton „I".
•
The red pushbutton „0" has to be pressed to
switch off the saw.
7.2 Parallel stop
7.2.1 Stop height (Fig. 7/8)
•
The parallel stop (7) supplied with the bench-
type circular saw has two different guide
faces.
•
For thick material you must use the stop rail
(25) as shown in Fig. 7, for thin material you
must use the stop rail as shown in Fig. 8.
•
To change the height of the stop, slacken the
two locking grips (12) and pull the stop rail
(25) off the carrier rail (26).
•
Turn the stop rail (25) 180° to the left or the
right, depending on the required height of the
stop, and plug in back on the carrier rail (26).
•
Tighten the locking grips (12).
7.2.2 Cutting width (Fig. 8)
•
The parallel stop (7) has to be used when
making longitudinal cuts in wooden workpi-
eces.
•
Slide the parallel stop (7) to the right or left
side of the saw table (1).
•
The parallel stop (7) can be set to the requi-
red dimension with the help of the scale (b)
engraved on the saw table (1).
•
Tighten the two thumb screws (12) in order to
fix the parallel stop (7).
7.3 Setting the angle (Fig. 9/10)
•
Undo the locking grips (14).
•
Slide the two locking grips (14) to set the bla-
de (4) to the required angle value (see scale
(13)).
•
Retighten the locking grips (14).
Anl_TH_TS_820_SPK1.indb 22 Anl_TH_TS_820_SPK1.indb 22
GB
8. Operation
After every new adjustment we recommend
you to make a trial cut in order to check the
new settings.
After switching on the saw, wait for the blade
to reach its maximum speed of rotation befo-
re commencing with the cut.
Secure long workpieces against falling off
at the end of the cut (e.g. with a roller stand
etc.)
Take extra care when starting the cut.
8.1 Cutting narrow workpieces
(width less than 120 mm) (Fig. 11)
•
Adjust the parallel stop (7) to the width of
workpiece you require.
•
Feed in the workpiece with two hands. Always
use the push stick (3) in the area of the saw
blade (4). (A push stick is supplied with the
saw!)
•
Always push the workpiece through to the
end of the splitter (5).
•
Important! With short workpieces, use the
push stick from the beginning.
8.2 Cutting extremely narrow workpieces
(width less than 30 mm)
•
Adjust the parallel stop (7) to the width of
workpiece you require.
•
Use the push block to press the workpiece
against the stop rail (25) and push the workpi-
ece with the push block through to the end of
the splitter (5).
There is no push block supplied with the
saw!
(Available from your specialist dealer)

9. Replacing the power cable

If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 22 -
10
Alw
ting
10.
•
•
•
10.
In c
bru
Imp
lace
10.
The
req
10.
Ple
rep
•
•
•
•
For
ww
22.05.13 16:36 22.05.13 16:36