Subscribe to Our Youtube Channel
Related Manuals for Hilti R4X12 S
Summary of Contents for Hilti R4X12 S
- Page 1 R4X12 S Operating instructions Mode d’emploi Manual de instrucciones Printed: 07.07.2013 | Doc-Nr: PUB / 5070503 / 000 / 00...
- Page 2 X-EDN19 THQ12MX HIGH SHEAR NAIL Base Material Thickness: 3/16" – 3/8" X-EDNK22 THQ12MX HIGH SHEAR NAIL Base Material Thickness: 1/8" – 1/4" X-ZF 22THS12M (temporary fastenings) Base Material Thickness: 1/8" – 1/4" Printed: 07.07.2013 | Doc-Nr: PUB / 5070503 / 000 / 00...
- Page 3 Printed: 07.07.2013 | Doc-Nr: PUB / 5070503 / 000 / 00...
-
Page 4: Table Of Contents
DO NOT use oxygen, combustible gases or high pres- sure compressed gas tanks as the air supply for the tool. ALWAYS use authentic Hilti R4X12 S fasteners and parts in your tool. SAFETY equipment such as safety glasses, hearing pro- tection and hard hat should ALWAYS be worn by the operator and bystanders when the tool is in use. -
Page 5: Technical Data For The R4X12 S
3.2 Lubricate the tool Use Hilti ATL (Air Tool Lubricant) or an equivalent light- weight acid-free, non-detergent oil (viscosity 3–4 Engler/20°C; aniline point 60°C). -
Page 6: Cold Weather (40°F Or Colder) Operation
Your Hilti air tool is precision engineered for safety and Hilti operates a nationwide network of Repair Centers, and rapid service is a hallmark of the Hilti system. If your durability. NEVER attempt to modify parts, since this tool requires service or warranty repairs, contact your... -
Page 7: R4X12 S Troubleshooting Guide
3. Check the regulator(s) for the correct air pressure and ● Flat blade screw driver that all valves to the supply line are open. ● Hilti 0-ring grease (Item no 12423) ● 0-ring Pick or Scribe 4. Check the fittings and hoses for kinks, leaks, or block- ●... -
Page 8: Instructions For Disassembly Of R4X12 S
Replace bumper Defective trigger valve body (#56) Replace trigger valve body assy 10. Instructions for disassembly of R4X12 S ward and away from magazine. Pull back grip (63) slight- (Use with Exploded View Drawings (2-4) and Parts list) ly, align grip pin (65) with detents in magazine and tilt back portion of grip up. -
Page 9: Instructions For Reassembly Of The R4X12 S
10.7) Using a replacement driver blade or an 8 mm diam- grease (Hilti #12423) prior to insertion. 11. Instructions for reassembly of the R4X12 S (Use with Exploded View Drawings (2-4) and Parts list 11.3 Piston driver blade assembly (16) (Bumper, cylinder and ring assembly already installed, NOTE: Clean all parts and check them for wear;... -
Page 10: R4X12 S Spare Parts
(8) and insert safety yoke arm in safety valve piston (54). Mount guide plate (2) and secure hex lock- nuts (3) with 10 mm fork wrench. 12. R4X12 S Spare Parts Ref # Hilti # Description Ref # Hilti #... -
Page 11: Manufacturer's Warranty - Tools
59296 Adhesive LOCTITE 270 50CCM 13. Manufacturer’s warranty – tools Hilti warrants that the tool supplied is free of defects Hilti is not obligated for direct, indirect, incidental in material and workmanship. This warranty is valid so or consequential damages, losses or expenses in... - Page 12 Fax: +423 / 234 29 65 www.hilti.com 284628 / A Hilti = registered trademark of Hilti Corp., Schaan W 3007 0604 00-Pos.1 Printed in Liechtenstein © 2004 Right of technical and programme changes reserved S. E. & O. Printed: 07.07.2013 | Doc-Nr: PUB / 5070503 / 000 / 00...
Need help?
Do you have a question about the R4X12 S and is the answer not in the manual?
Questions and answers