Remote Control Unit - TAD -D1DDOMK2 Owner's Manual

remote control unit

DISC PLAYER
1
TIME
2
SACD/CD
3
1
4
4
7
CLEAR
5
6
7
VOLUME
1  DISC PLAYER button
Use to set power to ON/standby mode.
2 TImE button
Press to display the disc's elapsed and remaining
playing time. Each time the button is pressed, the display
alternates as follows: [track remaining time] / [disc
remaining time] / [elapsed time].
3 SACD/CD button
Press to switch between play areas of hybrid discs. If this
button is pressed when disc play is stopped, switching
can be performed between the disc's CD area and SACD
area.
4 Number buttons
Use to designate specific tracks for playback. Press the
desired number button to select, followed by the ENTER
remote control operating range
When using the remote control unit to operate the TAD-D1000MK2, point the remote
control at the main unit's remote sensor within the ranges shown in the accompanying
illustration.
' The remote control may not operate properly if obstructions exist between the
remote control unit and the remote sensor, or if the angle between the remote
control and the remote sensor is poor.
' Malfunctions may occur if the TAD-D1000MK2 is used nearby other appliances that
emit infrared light, or if remote control units for other devices utilizing infrared light
are used nearby. Alternately, using this remote control unit near other appliances that also utilize infrared light may
cause those appliances to malfunction.
' Replace the batteries when you notice a reduction in the operating range of the remote control unit.
' The remote control may not operate correctly if strong sunlight or light from fluorescent lamps is allowed to strike the
remote sensor directly. In such cases, change the installation location, or remove the fluorescent lamps to a more
distant location.
OPEN/CLOSE
8
DISPLAY OFF
9
DAC MODE
10
2 3
5 6
8 9
0
ENTER
11
REPEAT
AMP
12
MUTE
button to confirm the selection.
5 CLEAR button
Press to cancel a currently input item. For example, this is
useful when an improper track number has been input.
6 Play operation buttons
 – Play disc.
g – Stop disc play.
e – Press to temporarily pause disc playback. Press the
button again to resume playback.
m – Press during playback to perform quick reverse.
 – Press during playback to return to the beginning of
the currently playing track.
n – Press during playback to perform fast forward.
 – Press to advance to beginning of next track.
7 REPEAT button
Each time the button is pressed the repeat play mode
alternates in the following order:
1 track repeat All track repeat
Repeat OFF
note
' Repeat mode is canceled if the disc play is stopped.
8 h OPEN/CLOSE button
Press to open and close the disc tray.
9 DISPLAY OFF button
Press to turn off display.
10 DAC mODE button
Press to switch DAC mode. Each time the button is
pressed the input mode alternates as follows:
U1 or U2 (USB input) / D1 (XLR) / D2 (coaxial) / D3
(coaxial) / D4 (optical) / CD/SACD disc playback mode
This operation can be performed when disc play is stopped.
11 ENTER button
Press to confirm settings and selections.
12 Amplifier operation buttons
These buttons can be used to operate a TAD amplifier.
 AmP – Amplifier power ON/standby
VOLUME (+/−) – Use to adjust sound volume.
mUTE – Press to temporarily mute the sound.
VOLUME (+/−) and mUTE can also be used to adjust the
line output volume of the TAD-D1000MK2. This button
is disabled if the output is fixed to the maximum value
on the unit. To enable volume adjustment by the remote
control, hold down the VOL (−) button on the unit.
Remote sensor
Remote
control unit
30°
30°
7 m (23 ft.)
13