Table of Contents
Advertisement
OPERATION
OPERATION
MEAT TEMP PROBE
POWER SWITCH
"P" SETTING
"P" SETTING
The main benefit to the "P" Button is that it allows you to fine tune your Pellet Grill to compensate for ambient
The main benefit to the "P" Button is that it allows you to fine tune your Pellet Grill to compensate
temperatures, humidity, wind, environmental changes, pellet fuel type and quality. Anytime the temperature
for ambient temperatures, humidity, wind, environmental changes, pellet fuel type and quality. Anytime the
dial is first turned to SMOKE the Auger will turn continuously for 2.5 minutes and then shut off for 2 minutes,
temperature dial is first turned to SMOKE the Auger will turn continuously for 2.5 minutes and then shut off for
to allow the fire to get established. The auger then starts to cycle, delivering fuel for 16 seconds, and then
2 minutes, to allow the fire to get established. The auger then starts to cycle, delivering fuel for 16 seconds,
and then proceeds to turns off. The same goes for next cycle.
proceeds to turns off. The same goes for next cycle.
When the "P" Button is pushed, the "P" SET 4 starts flashing on the LCD screen. Regulate setting by pushing
When the "P" Button is pushed, the "P" SET 4 starts flashing on the LCD screen. Regulate setting by pushing
"+" or "-". The corresponding "P" setting is displayed on the LCD screen momentarily. There are 8 "P" settings,
ranging from P0 to P7. Note: Factory default setting is "P4". Last push the "P" SET, the flashing stops and
"+" or "-". The corresponding "P" setting is displayed on the LCD screen momentarily. There are 8 "P" settings,
setting is completed. There are 8 "P" settings in SMOKE mode, ranging from P0 to P7. P0 has the highest
ranging from P0 to P7. Note: Factory default setting is "P4". Last push the "P" SET, the flashing stops and setting
temperature; P7 is the lowest temperature.
is completed. There are 8 "P" settings in SMOKE mode, ranging from P0 to P7. P0 has the highest temperature;
Do not increase the "P" setting too high when outside temperature is low. As this could result in the
P7 is the lowest temperature.
fire going out.
Do not increase the "P" setting too high when outside temperature is low. As this could result in the fire
"P" SET MANUAL FEEDING
going out.
Press and hold "P" button for 5 seconds, the "P" button on the LCD screen will continue flashing, and the feeding
system will continuously transfer pellets to the Burn Pot. There will be more smoke if this function is used in
"P" SET MANUAL FEEDING
SMOKE mode, with more heat being produced if used before opening the lid.
Press and hold "P" button for 5 seconds, the "P" button on the LCD screen will continue flashing, and the
"M" TIMER SETTING
feeding system will continuously transfer pellets to the Burn Pot. There will be more smoke if this function is
After pushing the "M" timer button, the screen displays 01:00, when "01" continues flashing you can regulate "+" or
used in SMOKE mode, with more heat being produced if used before opening the lid.
"-" to the desired hour. Proceed to push the "M" button, so "00" flashes to regulate "+" or "-" to the desired minute.
Every time you push "+" or "-" in hour/minute mode, it increases or decreases 1 hour/5 minutes.
"M" TIMER SETTING
Please note: Do not leave grill unattended for a long duration of time. If there are any grill fires, cut
After pushing the "M" timer button, the screen displays 01:00, when "01" continues flashing you can regulate "+"
off power immediately.
or "-" to the desired hour. Proceed to push the "M" button, so "00" flashes to regulate "+" or "-" to the desired
minute. Every time you push "+" or "-" in hour/minute mode, it increases or decreases 1 hour/5 minutes.
Please note: Do not leave grill unattended for a long duration of time. If there are any grill
fires, cut off power immediately.
18
"P" / "M" Setting
SMOKE
16
STAND BY
TEMP CONTROL
Hide quick links:
Advertisement
Table of Contents
