Pentair ChemCheck Installation And Service Manual page 3

INHALATION: Inhalation of vapors can cause
coughing, inflammation of the nose, throat
and upper respiratory tract and death. In case
of inhalation, move to an area with fresh air
immediately.
INGESTION: Swallowing can be fatal. Contact local poison control
center or physician immediately. Give large amounts of water or milk.
Allow person to vomit. If vomiting occurs, keep head lower than hips to
avoid aspiration. If person is unconscious, turn their head to the side.
Seek immediate medical attention.
STORAGE: Install and store container and acid in a dry, ventilated
place protected from excess heat and direct sunlight. Should be stored
at a temperature below 80°F (27°C). Be sure drainage is located away
from building and equipment.
SKIN CONTACT: Wash skin with soap and water for at least 20
minutes and remove contaminated clothing and shoes. Contaminated
clothes should be thoroughly cleaned before re-use.
EYE CONTACT: Flush eyes immediately with water for at least 20
minutes. Seek immediate medical attention.
PERSONAL PROTECTION
VENTILATION: Use container outside and in a well-ventilated area.
EYE PROTECTION: Use splash-resistant safety goggles.
CLOTHING: Wear chemical-resistant clothing when handling or
working with acid and chlorine.
GLOVES: Wear chemical-resistant gloves when handling or working
with acid and chlorine.
DISPOSAL: Because of its corrosive nature, muriatic acid is a
hazardous waste when spilled or discarded. Dispose of used acid at
an approved hazardous waste facility or at your municipal household
hazardous waste collection facility. Small spills of acid may be
neutralized using baking soda. Carefully pour the baking soda onto
the spilled material until the fizzing stops, then mop or scoop up the
residue. Leave cleanup of large spills to the experts; call your local fire
department or hazardous materials spill team.
IMPORTANT SAFETY INSTRUCTIONS
FCC Standard - 47 CFR Part 15, Subpart C (Section
15.247). This version is limited to chapter 1 to chapter 11
by specified firmware controlled in the U.S.A.
Instruction to user - This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Note: In order to maintain compliance with FCC regulations,
shielded cables must be used with this equipment. Operation with
non-approved equipment or unshielded cables is likely to result
in interference to radio and TV reception. The user is cautioned
that changes and modifications made to the equipment without
the approval of the manufacturer could void the user's authority to
operate this equipment.
Canada - Industry Canada (IC) Regulatory Notice: - This
device complies with RSS210 of Industry Canada. (1999).
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful
communication. This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may
cause undesired operation of the device.
Conformément à la réglementation d'Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir
le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire
à l'établissement d'une communication satisfaisante. Le présent
appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
CHEMCHECK™ Water Quality Monitor Install and Service Guide
iii