Advertisement
Exchange module/insert
Door station is dismantled.
Pull off connection terminal block (13) on the
video insert.
Remove the connection cables' connectors of
the module to be exchanged.
Loosen screws (20) of the module mounting at
the back (21) using a screwdriver and remove
the module mounting (Figure19).
Figure 19: Dismantling module mounting
(20) Screws
(21) Module mounting
The video insert can now be removed.
To remove the call push-button module, unlatch
the side retaining brackets (22) of the module
mounting by carefully lifting up with a screwdri-
ver (Figure 20).
(22)
Figure 20: Unlatching module
(22) Retaining brackets module mounting
Elcom Kommunikation GmbH - Gottfried-Leibniz-Str.1 - D-74172 Neckarsulm - www.hager.com -
Elcom Kommunikation GmbH - Gottfried-Leibniz-Str.1 - D-74172 Neckarsulm - www.hager.com -
After unlatching the two overlapping module
retaining brackets, the module detaches itself
from the anchoring (22).
Remove the module to be replaced and install
the new module in reverse order.
Automatic or manual addressing of the module
P
is required to operate the door station.
Appendix
Technical data
Operating voltage
Camera standby current
consumption
Camera current consumption
(operation)
Camera heating current consumption
(operation)
Current name plate lighting
per call push-button module
(21)
Menu
setting
0
1
2
3
4
5
6
7
8
9
(20)
10
Table 3: Brightness of LED backlighting
Door release contact T/T
potential-free
Door release unlocking time
Camera aperture angle horiz./vertical
Aperture angle swivelling range
horizontal/vertical
Camera resolution
Recommended camera installation height
Hexagon 1.5 mm camera
locating screw
Degree of protection
Degree of protection
(degree of impact resistance)
Relative humidity
Operating temperature
Switch on temperature camera heating
Storage/transport temperature
Connecting terminals
for conductor diameter
Dimensions:
Call push-button button small
Name plate insert small
Call push-button button medium-seize 75.8 x 32.6 mm
Name plate insert medium-sized
Width of name plate insert
Surface compensation with
fl ush-mounted installation
Dimensions video door station front (W x H x D):
with 0.5 or 1 module
with 0.5 and 1 module
with 2 modules
with 0.5 and 2 modules
with 3 modules
with 2 x 2 modules
with 3 und 2 modules or
with 2 x 3 modules
22 ... 24 V=
approx. 8 mA
max. 240 mA
100 mA
45 mA
Backlighting On
Backlighting Off
Permanent Off
≈ 750 lx
≈ 1600 lx
.
.
.
.
.
.
.
.
.
.
.
.
.
.
≈ 60 lx
≈ 110 lx
Permanent On
max. 24 V/1 A
1 ... 10 s
82°/58°
42.5°
500 x 582 px
1.5 m
M2 x 10 mm
IP 44
0 ... 65% (no condensation)
-20°C ... +55°C
ca. 20°C
-30°C ... +80°C
0.5 ... 0.8 mm
75.8 x 14.5 mm
72.1 x 12 mm
72.1 x 30.1 mm
max. 0.5 mm
max. 17 mm
133.5 x 242 x 2 mm
133.5 x 295.8 x 2 mm
133.5 x 332 x 2 mm
133.5 x 385.8 x 2 mm
133.5 x 422 x 2 mm
225.5 x 332 x 2 mm
225.5 x 422 x 2 mm
Accessories (extract)
Flush-mounted housing for door station:
with 0.5 or 1 module
with 0.5 and 1 module
with 2 modules
with 0.5 and 2 modules
with 3 modules
with 2 x 2 modules
with 3 and 2 modules or
with 2 x 3 modules
Surface-mounted housing for door station:
with 0.5 module or 1 module
with 0.5 module and 1 module
with 2 modules
with 0.5 and 2 modules
with 3 modules
with 2 x 2 modules
with 3 and 2 modules or
with 2 x 3 modules
IK07
REW111X
REW112X
REW113X
REW114X
REW115X
REW126X
REW127X
REW211X
REW212X
REW213X
REW214X
REW215X
REW226X
REW227X
08/2015 - 6LE000719A
08/2015 - 6LE000719A
Advertisement
