Table of Contents
Advertisement
Quick Links
Getting started with the X-NUCLEO-USBPDM1 USB Type-C™ Power Delivery
Sink expansion board based on TCPP01-M12 for STM32 Nucleo
Introduction
The
X-NUCLEO-USBPDM1
any
STM32 Nucleo
development board equipped with a USB Type-C peripheral.
The
X-NUCLEO-USBPDM1
USB-IF certified (Test ID certification: 3036).
It provides a straightforward means for evaluating USB Type-C Power Delivery in Sink mode based on TCPP01-M12.
The USB Type-C connector can supply the
UM2668 - Rev 2 - May 2020
For further information contact your local STMicroelectronics sales office.
is an expansion board for the
is compliant with USB Type-C Rev 1.2 and Power Delivery 3.0 with 100 W PPS support, as well as
STM32 Nucleo
Figure 1.
X-NUCLEO-USBPDM1 expansion board
NUCLEO-G071RB
and
NUCLEO-G474RE
development board thanks to a 3.3 V LDO.
UM2668
User manual
development boards or
www.st.com
Advertisement
Table of Contents
Related Manuals for ST X-NUCLEO-USBPDM1
Summary of Contents for ST X-NUCLEO-USBPDM1
-
Page 1: Figure 1. X-Nucleo-Usbpdm1 Expansion Board
UM2668 User manual Getting started with the X-NUCLEO-USBPDM1 USB Type-C™ Power Delivery Sink expansion board based on TCPP01-M12 for STM32 Nucleo Introduction X-NUCLEO-USBPDM1 is an expansion board for the NUCLEO-G071RB NUCLEO-G474RE development boards or STM32 Nucleo development board equipped with a USB Type-C peripheral. -
Page 2: Getting Started
NUCLEO-G071RB NUCLEO-G474RE development boards hosting STM32G071RB STM32G474RE microcontrollers, respectively. The expansion board must be plugged on the matching pins of the development board connector. Figure 2. X-NUCLEO-USBPDM1 plugged on an STM32 Nucleo board UM2668 - Rev 2 page 2/19... -
Page 3: Software Requirements
UM2668 Software requirements Software requirements • All-in-one multi-OS software tool for programming STM32 products (STM32CubeProg) • ST-LINK/V2-1 USB driver • Binary files with specific use-cases (X-CUBE-USBPDM1) UM2668 - Rev 2 page 3/19... -
Page 4: Board Component Description And Configuration
Other connections among the two boards are configured by JP2 jumpers. The global jumper setup is the following: • LDO OUT – 3.3 V to connect the LDO output to 3.3 V on the X-NUCLEO-USBPDM1. The STM32 is powered by the USB Type-C connector. Note:... -
Page 5: Usb Type-C D+/D- Connections
To change the threshold to another value (6 V, 10 V, 13 V or 17 V), R0 must be removed and a solder bridge must be added on the selected OVP voltage. USB Type-C D+/D- connections On the X-NUCLEO-USBPDM1 expansion board bottom side, D+/D- lines from USB Type-C CN1 are connected to D+/D- lines of the NUCLEO-G474RE development board thanks to R8 and R9 zero Ohm resistors. -
Page 6: Programming And Debugging
UM2668 Programming and debugging Programming and debugging For programming and debugging, the X-NUCLEO-USBPDM1 expansion board must be powered by the STM32 Nucleo development board. JP2 LDO OUT – 3.3 V and 3.3 V – NRST pins must be removed. TCPP01-M12 can be powered by one of the following options: •... -
Page 7: Usb Type-C Powered Mode
Once STM32 is programmed, it is possible to power the STM32 using USB Type-C V voltage through a source device connected to the Type-C connector (CN1). The X-NUCLEO-USBPDM1 on-board LDO (U2) generates 3.3 V to supply the system. In this case, 5 V is not available yet on the... -
Page 8: Nucleo-G474Re Type-C Powered Mode Sink Contract Negotiation
NUCLEO-G474RE Type-C powered mode Sink contract negotiation In this case, dead battery clamps are removed when 3.3 V jumper is connected (not in low power mode). NUCLEO-G474RE must be powered by ST-LINK micro-USB connector (JP5 5V_STLK jumper closed). Step 1. Connect the NUCLEO-G474RE micro-USB connector (CN1) to your PC. -
Page 9: Nucleo-G071Rb Type-C Powered Mode Sink Contract Negotiation
NUCLEO-G071RB Type-C powered mode Sink contract negotiation In this case, dead battery clamps are managed by STM32G071RB in low power mode. NUCLEO-071RB must be powered by ST-LINK micro-USB connector (JP2 STLK jumper closed). Step 1. Connect the NUCLEO-071RB micro-USB connector (CN1) to your PC. -
Page 10: Jumper Tables
Jumper NUCLEO-G071RB selection NUCLEO-G474RE selection CC1_G0 CC2_G0 CC1_G4 CC2_G4 Table 2. JP2 connector - low power mode USB-Type-C powered Jumper ST-LINK powered USB-Type-C powered ST-LINK removed LDO OUT–3.3 V 3.3 V–NRST FLT–FLT_IN –3.3 V –V _OUT DB–3.3 V DB–DB_OUT Table 3. -
Page 11: Schematic Diagrams
Schematic diagrams Figure 3. X-NUCLEO-USBPDM1 circuit schematic (1 of 2) CC1_G4 CC1_G0 CC2_G4 PA5_G0 CN10 3.3V VCC_OUT DP_G4 1314 1314 DM_G4 FLT_IN 2324 2324 DB_OUT CC2_G0 3334 3334 NRST PA4_G0 VBUS ADC_VBUS 3.3V VBUS LDO_OUT LDO_OUT NRST 100nF 470nF FLT_IN... -
Page 12: Figure 4. X-Nucleo-Usbpdm1 Circuit Schematic (2 Of 2)
Figure 4. X-NUCLEO-USBPDM1 circuit schematic (2 of 2) VBUSc VBUS GATE SENSE Fiducial on board VBus max P max VBUS 2.7K STL11N3LLH6 3.3V VBUS 1.5K 1.1K BAT54KFILM 1.0K 100nF IN_GD GATE SOURCE 3.3V VBus 820R GREEN 620R 100W VBUS_CTRL CC1c... -
Page 13: Bill Of Materials
UM2668 Bill of materials Bill of materials Table 4. X-NUCLEO-USBPDM1 bill of materials Item Q.ty Ref. Part/Value Description Manufacturer Order code USB_TypeC_Rec Type-C Wurth 632723300011 eptacle connector Electronics Inc. Through-hole, Screw Wurth 2x1, 2.54 mm 691210910002 connector Electronics Inc. pitch Strip 19x2, 2.54... - Page 14 UM2668 Bill of materials Item Q.ty Ref. Part/Value Description Manufacturer Order code Wurth SMD 0603 Red LED 150060RS75000 Electronics Inc. Wurth SMD 0603 Green LED 150060GS75000 Electronics Inc. N-channel 30 V, 30 V, 11 A, 6 mOhm typ., 11 PowerFLAT 3.3 x STL11N3LLH6 A STripFET H6 Power MOSFET...
-
Page 15: Revision History
UM2668 Revision history Table 5. Document revision history Date Version Changes 17-Dec-2019 Initial release. 14-May-2020 Updated Introduction and Section 1.1 Overview. UM2668 - Rev 2 page 15/19... -
Page 16: Table Of Contents
UM2668 Contents Contents Getting started ..............2 Overview . - Page 17 X-NUCLEO-USBPDM1 bill of materials........
- Page 18 X-NUCLEO-USBPDM1 plugged on an STM32 Nucleo board ........
- Page 19 ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’...
Need help?
Do you have a question about the X-NUCLEO-USBPDM1 and is the answer not in the manual?
Questions and answers