Advertisement

BM 58
EN Blood pressure monitor
Instructions for use

Advertisement

Table of Contents
loading

Summary of Contents for Beurer BM 58

  • Page 1 BM 58 EN Blood pressure monitor Instructions for use...
  • Page 2: Table Of Contents

    USB cable 4 x LR6 AA batteries Best regards, Storage bag Your Beurer Team Instructions for use 1. Getting to know your instrument Check that the device packaging has not been tampered Dear Customer, with and make sure that all contents are present.
  • Page 3: Important Information

    contact your retailer or the specified Customer Services Observe the instructions for use address. The upper arm blood pressure monitor is used for non-inva- sive measurement and monitoring of adults’ arterial blood Application part, type BF pressure. You can use it to measure your blood pressure quickly and easily, storing the results and displaying the progression of readings together with the average.
  • Page 4 in a car, ambulance or helicopter, or whilst undertaking Serial number physical activity such as playing sport) can influence the measurement accuracy and cause incorrect measure- The CE labelling certifies that the prod- ments. uct complies with the essential require- •...
  • Page 5 • During the blood pressure measurement, blood circula- • The device is only intended for the purpose described in tion must not be stopped for an unnecessarily long time. these instructions for use. The manufacturer is not liable If the device malfunctions, remove the cuff from the arm. for damage resulting from improper or careless use.
  • Page 6 We can no longer guarantee perfect functioning if you do. • Observe the plus (+) and minus (-) polarity signs. • Repairs may only be performed by Beurer Customer Ser- • If a battery has leaked, put on protective gloves and clean vice or authorized dealers.
  • Page 7: Unit Description

    3. Unit description Notes on electromagnetic compatibility • The device is suitable for use in all environments listed in these instructions for use, including domestic environ- ments. • The use of the device may be limited in the presence of electromagnetic disturbances.
  • Page 8: Prepare Measurement

    For this, you will need a standard USB cable (included in in use. To operate the device, move the touch screen activa- delivery) and the "beurer HealthManager" computer soft- tion switch to ON. When the touch screen display is touched ware.
  • Page 9 To set the date and time, proceed as follows: If the battery change is continuously illuminated, • Move the touch screen activation switch to the ON posi- measurement is no longer possible and you must replace all tion. the batteries. Once batteries have been removed from the •...
  • Page 10: Measuring Blood Pressure

    monitor. The mains part must only be connected to the Now tighten the free end of the mains voltage that is specified on the type plate. cuff, but make sure that it is not • Then insert the mains plug of the mains part into the too tight around the arm and close mains socket.
  • Page 11 If the values between the two arms are significantly differ- • To carry out a blood pressure measurement, make sure ent, please consult your doctor to determine which arm you are sitting comfortably with your arms and back lean- should be used for the measurement. ing on something.
  • Page 12: Evaluating Results

    • Heart rate, systolic and diastolic blood pressure are dis- slow or excessively fast heart rate) may be caused, among played. other things, by heart disease, age, physical predisposition, excessive use of stimulants, stress or lack of sleep. Arrhyth- • You can cancel the measurement at any time by press- mia can only be ascertained through examination by your ing the START/STOP button or by pushing the touch...
  • Page 13: Saving, Retrieving And Deleting Results

    diastole in the Normal category), the graphical classifica- measured data, the earliest items of data measured are tion on the device always shows the higher category; for the lost. example given this would be High normal. • Move the touch screen activation switch to the ON posi- tion.
  • Page 14: Transferring Measurements

    • pumping up takes longer than 160 seconds PC is shown on the display. Begin the data transfer appears on the display) in the "beurer HealthManager" PC software. • there is a system or device error During the data transfer, an animation is shown appears on the display) on the display.
  • Page 15: Cleaning And Storing The Device And Cuff

    800 –1050 hPa ambient pres- sure 11. Specifications Power supply AA batteries 4 x 1,5 V Model no. BM 58 Battery life For approx. 500 measurements, Measurement Oscillometric, non-invasive blood pres- depending on the blood pressure level method sure measurement on the upper arm...
  • Page 16: Mains Part

    100 – 240 V, 50 – 60 Hz, 0.5 A max IEC 61000-4-6, IEC 61000-4-8, IEC 61000-4-11) and is Output 6 V DC, 600 mA, only in connection with beurer subject to particular precautions with regard to electro- blood pressure monitor.
  • Page 17: Replacement Parts And Wearing Parts

    During the warranty period, should this product prove to be 14. Warranty / service incomplete or defective in functionality in accordance with the following provisions, Beurer shall carry out a repair or Beurer GmbH, Söflinger Straße 218, 89077 Ulm, Germany a replacement delivery free of charge, in accordance with (hereinafter referred to as “Beurer”) provides a warranty for...
  • Page 18 A warranty claim shall only be considered if the buyer can Repairs or an exchange in full do not extend the warranty provide Beurer, or an authorised Beurer partner, with period under any circumstances. – a copy of the invoice/purchase receipt, and –...
  • Page 20 Beurer GmbH Söflinger Straße 218 89077 Ulm, Germany www.beurer.com www.beurer-gesundheitsratgeber.com www.beurer-healthguide.com • www.beurer-blutdruck.de...

Table of Contents