Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ETAS ES1652.2
Summary of Contents for ETAS ES1652.2
- Page 1 ES1652.2 Carrier Board for Signal Conditioning Circuits User’s Guide...
- Page 2 The data in this document may not be altered or amended without special noti- fication from ETAS GmbH. ETAS GmbH undertakes no further obligation in rela- tion to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license.
-
Page 3: Table Of Contents
5 ETAS Contact Addresses ........ - Page 4 Contents ETAS ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide...
-
Page 5: Introduction
Features The ES1652.2 Carrier Board for Signal Conditioning Circuits is used to accommo- date modules for signal conditioning (example: PB1652LAMBDA.1-B Signal Con- ditioning for Lambda Sensor Simulation). Fig. 1-1 Front Panel of the ES1652.2 Carrier Board for Signal Conditioning... - Page 6 If required, this must be ensured by the customer on the relevant piggyback. Up to four DC/DC converters can be installed on the ES1652.2 Carrier Board to power the piggyback. These can be supplied with either +5 V or +12 V from the VMEbus backplane.
-
Page 7: Basic Safety Instructions
Please adhere to the safety instructions in this manuals to avoid injury to yourself and others as well as damage to the device. 1.2.1 Correct Use ETAS GmbH cannot be made liable for damage which is caused by incorrect use and not adhering to the safety instructions. 1.2.2 Labeling of Safety Instructions... -
Page 8: Ce Marking
The user is obliged to collect the old devices separately and return them to the WEEE take-back system for recycling. The WEEE Directive concerns all ETAS devices but not external cables or batteries. For more information on the ETAS GmbH Recycling Program, contact the ETAS sales and service locations (see "ETAS Contact Addresses"... -
Page 9: Hardware Description
Power Supply To power the piggybacks, up to four DC/DC converters can be accommodated on the ES1652.2 Carrier Board for Signal Conditioning Circuits for the purposes of voltage stabilization and galvanic isolation. The output voltages DC1 - DC4 of the converters are connected with the con- nector strip CO101 (see ""CO101"... -
Page 10: Configuration Of The Input Voltage Of The Dc/Dc Converters
Mapping of Supply Voltage and DC/DC Converter Supply Voltage DC/DC Converter (Type) +5 V TEN3-0522N +12 V TEN3-1222 Tab. 2-1 DC/DC Converters for the Supply Voltages +5 V and +12 V ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide... -
Page 11: Fuses
ETAS Hardware Description Fuses There are three fuses on the ES1652.2 Carrier Board that provide protection against the voltages from the VMEbus backplane. IC100 IC101 FU102 FU101 FU100 IC102 IC103 Fig. 2-3 Position of the Fuses on the ES1652.2 Carrier Board... - Page 12 Hardware Description ETAS ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide...
-
Page 13: Pin Assignment
Pin 5: "OUT 5" Pin 4: "OUT 4" Pin 3: "OUT 3" Pin 2: "OUT 2" Pin 1: "OUT 1" Tab. 3-1 Connections from "CO100" to LEDs, "IN 1..9" and "OUT 1..15" ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide... -
Page 14: Co101" Connector
Ground * Reserved Reserved Reserved Ground * Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Ground* Ground * * from the VMEbus backplane Tab. 3-2 Pin Assignment of Connector "CO101" ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide... -
Page 15: Technical Data
0 to 95% (non-condensing) Physical Dimensions Height Width 4 HP Fulfilled Standards and Norms The ES1652.2 Carrier Board for Signal Conditioning Circuits complies with the following standards and norms: Norm Test EN 61326-1 Electrical equipment for measurement, control and laboratory use – EMC requirements... - Page 16 Technical Data ETAS ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide...
-
Page 17: Etas Contact Addresses
For details of your local sales office as well as your local technical support team and product hotlines, take a look at the ETAS website: ETAS subsidiaries WWW: www.etas.com/en/contact.php ETAS technical support WWW: www.etas.com/en/hotlines.php ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide... - Page 18 ETAS Contact Addresses ETAS ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide...
-
Page 19: Index
ETAS Contact Addresses 17 Waste Electrical and Electronic Equip- ment 8 WEEE take-back system 8 Features 5 Fuses 11 LEDs on the front panel addressing 11 Pin assignment 13 Power supply 9 ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide... - Page 20 Index ETAS ES1652.2 Carrier Board for Signal Conditioning Circuits - User’s Guide...
Need help?
Do you have a question about the ES1652.2 and is the answer not in the manual?
Questions and answers