Table of Contents
Advertisement
Quick Links
Operation Manual
ARTICLE 51707
40" Lawn Aerator
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH
Seite 16
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Advertisement
Table of Contents
Related Manuals for WilTec 51707
Summary of Contents for WilTec 51707
- Page 1 Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 16 http://www.WilTec.de http://www.aoyue.eu...
- Page 2 The information contained in this document is subject to change without prior notice. No part of this document can be copied or duplicated in another form without the prior written consent of WilTec Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram.
-
Page 3: Notes On Safe Operation
Do not drive too close to a stream or ditch. 11. Do not tow this unit on a highway or other public road. 12. Follow the maintenance instructions as described in this manual. © by WilTec Wildanger Technik GmbH Seite 18 http://www.WilTec.de http://www.aoyue.eu... -
Page 4: Scope Of Delivery
SCOPE OF DELIVERY Description Plate Central Support Side Plate (x2) Handle Coupling Rod Axis Clutch Wheel (x2) Wheel Holder (x3) Double Coil (x2) Single Coil (x2) CONTENT ASSEMBLY PACKAGE © by WilTec Wildanger Technik GmbH Seite 19 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... -
Page 5: Assembly Instruction
(Smaller hole) Attach the 5/16" Hex Lock Nut to the bolt. Do not tighten screws. Step 2: Mount the short side of the axle shaft. © by WilTec Wildanger Technik GmbH Seite 20 http://www.WilTec.de http://www.aoyue.eu... - Page 6 1. Start with a 0.79" spacer 2. Ø20 Washer 3. Central support 4. Ø20 Washer 5. 1,61” Spacer 6. Double coil (knives point inwards) 7. Single coil 8. 2,76” Spacer 9. Ø20 Washer © by WilTec Wildanger Technik GmbH Seite 21 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 7 Make sure that the wheels are turn freely after as- sembly. 1. Wheel mounting 2. Hexagon head screw 1/2” x 4-7/16” 3. Hexagon nut 1/2” 4. Locking nut 1/2” © by WilTec Wildanger Technik GmbH Seite 22 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 8 1/4" spacers per bolt, and the 5/16" hex lock nut. Tighten all connections. 1. Hexagon head screw 5/16x1-3/16” 2. Hexagon nut 5/16” x 1” 3. Locking nut 5/16” 4. 1/4” Spacer © by WilTec Wildanger Technik GmbH Seite 23 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 9 5/16" x 1-3 / 16" hexagonal bolt, spacer and 5/16" hexagonal lock nut. Tighten the connections firmly. 1. Hexagon head screw 5/16” x 1-3/16” 2. Locking nut 5/16” 3. Spacer © by WilTec Wildanger Technik GmbH Seite 24 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 10 The locking device is designed to help prevent the handle from slipping out when the lawn aerator is in use. But if you feel that this part does not fit correctly, simply remove the pin. © by WilTec Wildanger Technik GmbH Seite 25 http://www.WilTec.de...
-
Page 11: Operation
11. Small stones and pebbles that come to the surface through ventilation should then be collected so that other equipment, such as lawn mowers are not damaged. ATTENTION: TO AVOID INJURY, DISCONNECT THE AERATOR FROM THE TRACTOR WHEN LIFTING OR LOWERING THE FAN BLADES. © by WilTec Wildanger Technik GmbH Seite 26 http://www.WilTec.de http://www.aoyue.eu... -
Page 12: Maintenance
2. Before storage, clean the aerator and lightly oil exposed metal parts to prevent rusting. LUBRICATION 1. Oil the coil units and the shaft as required. 2. Oil the wheel as required. EXPLOSION DRAWING © by WilTec Wildanger Technik GmbH Seite 27 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... -
Page 13: Parts List
Hexagon bolt 5/16” x 1” 1.61” Spacer 2.36” Spacer 1/4” pacers Point of a knife Grip cap Carriage screw 5/16” x 7/8” Washer Ø20 Hexagon lock nut 5/16” 2.76” Spacer Spacers © by WilTec Wildanger Technik GmbH Seite 28 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 14 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.