Page 1
The TENS+ Company Ltd. Units C,D and E, 2nd Floor Albert Mill, Compstall Mill Estate, Andrew Street, Compstall, Stockport, SK6 5HN. Tel: 0161 427 4851 Fax: 0161 427 0215 Email: sales@thetenscompany.co.uk www.tensmachineuk.com Company registration number 08961942 Vat registration number 184 9281 69...
Page 2
Hi-Dow Wireless TENS & EMS System Instruction & User Manual Please read this user manual before using this device...
Contents GENERAL DESCRIPTION WARNINGS & PRECAUTIONS INTRODUCTION TO TENS CONTENTS & GENERAL INFORMATION INSTRUCTIONS FOR USE STEP BY STEP TREATMENT PROGRAMME CHOICE AND TREATMENT RECOMMENDATIONS 13 ELECTRODE PLACEMENT TROUBLESHOOTINGS MAINTENANCE, TRANSPORTATION AND STORAGE OF TENS DEVICE TECHNICAL SPECIFICATIONS PATIENT ACCESSORIES...
The Med-Fit Wireless TENS/EMS System is a battery operated wireless pulse generator that sends electrical impulses from a REMOTE control to RECEIVER (round) with ELECTRODE attached to them that are placed on the body to stimulate the nerves causing pain. When this happens, the nerves “FEEL” gentle electrical sensations instead of the pain.
It is recommended that proper medical advice on the use of TENS is sought from a Qualified Practitioner (Physiotherapist, Doctor or Nurse) prior to use, in order to ensure safe and effective treatment.
TENS for short. A TENS unit is a portable, pocket-sized, battery-powered device. The TENS unit uses mild, safe electrical signals to help control pain and delivers How does TENS work? the electrical signal to the body through a connection of a lead wire and self adhesive conductive electrode.
Page 7
During the TENS treatment If your muscles start to twitch. This may mean that the TENS signals are too strong or too fast. If you cannot feel any tingling at all. This may mean that the signal is too weak or too slow.
Please check carefully the contents of the Hi-Dow wireless TENS 1. Remote Control Unit CONTENTS & GENERAL INFORMATION 2. White TENS Module 3. Black TENS Module 4. AC adaptor 5. USB and AC Adaptor Charging Leads x2 6. Self Adhesive Electrode x4 7.
Page 9
Battery Charging Charging the Remote Using the AC Adaptor Please fully charge the batteries in both the remote unit and TENS modules before using this device. Connect the small end of the USB cable to the remote and the larger end to the AC adaptor (as shown in Fig 1) Plug the adaptor into any standard mains socket.
M4 (an explanation of the choice of modes is under section ???) Pressing the C button changes the display from 1,2 or 3 for example This setting would indicate the remote is set for m mode/programme 1 and TENS module 1.
Set up guide Switch on the remote unit and the white (no1) TENS module. (Green Light Indicates the unit is on). Connect either the large lumbar electrode or two pad electrodes to the module as shown Now firmly place the unit on to the painful site of your body to be treated see examples shown.
Page 12
Set up for using two TENS modules This unique TENS device allows you to treat larger areas or two different body parts at the same time see examples To use a second TENS module (Black TENS Module Number 2) simply press the M button on your remote so that the display shows.
Four programme modes for fast effective pain relief Programme / Mode 1 All modes are set with 30 minute treatment times. Simply switch the TENS module on to re-start a 30 minute treatment session Programme / Mode 2 High Frequency Pain Block Stimulation. This is the recommended programme to...
1. The REMOTE is not turning on or I can’t see anything on the screen. • Make sure the REMOTE has been fully charged. 2. The power light of RECEIVER flashes continuously. • Charge the RECEIVER soon or it will turn off automatically. 3.
6. The packed EMS device should be stored and transported under the temperature range of -20°C ~ + 60°C, relative humidity 20% ~ 95%, Atmosphere pressure 500hPa ~ 1060hPa. MAINTENANCE, TRANSPORTATION AND STORAGE OF TENS DEVICE Telephone: 0800 121 4626 www.thetenscompany.co.uk...